Burak Demir
Research Subjects
Burak Demir has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
Erhan Ayas
7 shared publications- Erkul Karacaoglu
Karamanoglu Mehmetbey University
4 shared publications Enes Ibrahim Duden
Eskisehir Tech Univ, Dept Mat Sci & Engn, TR-26555 Eskisehir, Turkiye
2 shared publicationsAnil Imak
1 shared publication- Asli Asiye Agil
Department of Materials Science and Engineering Faculty of Engineering Hakkari University Hakkari Turkey
1 shared publication Dilara Derince
1 shared publication
Latest Publications
- 1 July 2026
- Published by Bingol Universitesi in Türk Doğa ve Fen Dergisi
- Vol. 15 (2) , 154-163
Structural and Mechanical Characterization of Natural Fluoroapatite/3Y-TZP Composites Consolidated by Spark Plasma Sintering
This study investigates the structural and mechanical properties of natural fluoroapatite (FAP)/3 mol% yttria-stabilized zirconia (3YSZ) composites consolidated by spark plasma sintering (SPS). Powder mixtures containing 0–100 vol.% 3YSZ were prepared and sintered at optimized temperatures between 800 and 1300 °C under 50 MPa for 10 min. Phase composition, microstructure, density, hardness, and fracture toughness were systematically characterized using XRD, SEM-EDS, Archimedes’ method, and Vickers indentation. High relative densities (96–99%) were achieved within short sintering times. XRD results confirmed the coexistence of tetragonal YSZ and hexagonal FAP phases without detectable secondary reactions. Mechanical properties increased with increasing YSZ content. Pure YSZ exhibited the highest hardness (13.66 GPa) and fracture toughness (5.52 MPa m0.5), while the 95YSZ–5FAP composite retained relatively high mechanical performance (13.46 GPa, 4.42 MPa m0.5). Higher FAP contents led to significant reductions in toughness. The results demonstrate that SPS enables dense bioactive composites while preserving the mechanical integrity of zirconia-rich compositions.
- 1 July 2026
- Published by Bingol Universitesi in Türk Doğa ve Fen Dergisi
- Vol. 15 (2) , 154-163
Structural and Mechanical Characterization of Natural Fluoroapatite/3Y-TZP Composites Consolidated by Spark Plasma Sintering
This study investigates the structural and mechanical properties of natural fluoroapatite (FAP)/3 mol% yttria-stabilized zirconia (3YSZ) composites consolidated by spark plasma sintering (SPS). Powder mixtures containing 0–100 vol.% 3YSZ were prepared and sintered at optimized temperatures between 800 and 1300 °C under 50 MPa for 10 min. Phase composition, microstructure, density, hardness, and fracture toughness were systematically characterized using XRD, SEM-EDS, Archimedes’ method, and Vickers indentation. High relative densities (96–99%) were achieved within short sintering times. XRD results confirmed the coexistence of tetragonal YSZ and hexagonal FAP phases without detectable secondary reactions. Mechanical properties increased with increasing YSZ content. Pure YSZ exhibited the highest hardness (13.66 GPa) and fracture toughness (5.52 MPa m0.5), while the 95YSZ–5FAP composite retained relatively high mechanical performance (13.46 GPa, 4.42 MPa m0.5). Higher FAP contents led to significant reductions in toughness. The results demonstrate that SPS enables dense bioactive composites while preserving the mechanical integrity of zirconia-rich compositions.
- 24 December 2025
- Published by Elsevier in Ceramics International
- Vol. 52 (5) , 5789-5797
Enhancing the photoluminescence performance of Sm-doped fluorapatite with Dy co-doping
- 24 December 2025
- Published by Elsevier in Ceramics International
- Vol. 52 (5) , 5789-5797
Enhancing the photoluminescence performance of Sm-doped fluorapatite with Dy co-doping
- 18 December 2025
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1050
Novel MoSi2-MoB2 composites: Single-step in-situ synthesis from elemental powders via spark plasma sintering
- 18 December 2025
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1050
Novel MoSi2-MoB2 composites: Single-step in-situ synthesis from elemental powders via spark plasma sintering
- 5 September 2025
- Published by Elsevier in Solid State Sciences
- Vol. 169
Investigating mechanical properties of WAlB MAB phase synthesized via spark plasma sintering
- 5 September 2025
- Published by Elsevier in Solid State Sciences
- Vol. 169
Investigating mechanical properties of WAlB MAB phase synthesized via spark plasma sintering
- 12 October 2023
- Published by Elsevier in Ceramics International
- Vol. 50 (1) , 197-204
Mechanical properties and oxidation behavior of (Mo,W)AlB, (Mo,Cr)AlB, and (Mo,W,Cr)AlB MAB solid solutions synthesized with spark plasma sintering
- 12 October 2023
- Published by Elsevier in Ceramics International
- Vol. 50 (1) , 197-204
Mechanical properties and oxidation behavior of (Mo,W)AlB, (Mo,Cr)AlB, and (Mo,W,Cr)AlB MAB solid solutions synthesized with spark plasma sintering
- 14 April 2023
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 953
Characterization of MoAlB ceramics synthesized via spark plasma sintering with Si addition and SiC reinforcement
- 14 April 2023
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 953
Characterization of MoAlB ceramics synthesized via spark plasma sintering with Si addition and SiC reinforcement
- 1 October 2022
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 11 (10) , 106001
Synthesis and Characterization of Luminescent Er3+-Doped Natural Fluorapatite
Ca10(PO4)6F2:xEr3+ (x = 0.1, 0.3 and 0.5) was synthesized using solid-state powder process (1150 °C, 1h), conventional sintering (1150 °C, 1h), and spark plasma sintering (SPS) techniques (1150 °C, 10 min, and 50 MPa). XRD analysis revealed that all samples are generally composed of fluorapatite (FAP) containing quartz as a minor phase, and the presence of Er2O3 peaks is becoming more evident as Er-doped increases. In the SEM microstructure images, non-diffused Er2O3 particles also increase with doping in powder and pellet samples. However, the PL analysis showed that the luminescence intensity did not increase proportionally with the doping content caused by the concentration quenching effect. FAP samples doped with 0.3 mol Er have higher luminescence intensity than 0.1 and 0.5 mol Er-doped samples. In addition, powder samples have the highest luminescence intensity due to increased luminescence intensity with increasing crystallite size. The characteristic 2H11/2 to 4I15/2 emission bands of Er3+ at ∼530 nm are seen in all samples. The maximum average lifetime was obtained in 125 μs in the powder sample with 0.3 mol Er. CIE color coordinates demonstrate the standard green color under ∼ 275 nm excitation; eventually, these phosphors can be utilized as green phosphors for optical applications.
- 1 October 2022
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 11 (10) , 106001
Synthesis and Characterization of Luminescent Er3+-Doped Natural Fluorapatite
Ca10(PO4)6F2:xEr3+ (x = 0.1, 0.3 and 0.5) was synthesized using solid-state powder process (1150 °C, 1h), conventional sintering (1150 °C, 1h), and spark plasma sintering (SPS) techniques (1150 °C, 10 min, and 50 MPa). XRD analysis revealed that all samples are generally composed of fluorapatite (FAP) containing quartz as a minor phase, and the presence of Er2O3 peaks is becoming more evident as Er-doped increases. In the SEM microstructure images, non-diffused Er2O3 particles also increase with doping in powder and pellet samples. However, the PL analysis showed that the luminescence intensity did not increase proportionally with the doping content caused by the concentration quenching effect. FAP samples doped with 0.3 mol Er have higher luminescence intensity than 0.1 and 0.5 mol Er-doped samples. In addition, powder samples have the highest luminescence intensity due to increased luminescence intensity with increasing crystallite size. The characteristic 2H11/2 to 4I15/2 emission bands of Er3+ at ∼530 nm are seen in all samples. The maximum average lifetime was obtained in 125 μs in the powder sample with 0.3 mol Er. CIE color coordinates demonstrate the standard green color under ∼ 275 nm excitation; eventually, these phosphors can be utilized as green phosphors for optical applications.
- 17 April 2022
- Published by Elsevier in Materialia
- Vol. 22
Synthesis of Cr2AlB2 MAB phase via Spark Plasma Sintering: Effect of temperature, dwell time, and Al content
- 17 April 2022
- Published by Elsevier in Materialia
- Vol. 22
Synthesis of Cr2AlB2 MAB phase via Spark Plasma Sintering: Effect of temperature, dwell time, and Al content