Oleksandr Semenets
Research Subjects
Oleksandr Semenets has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Leonid Kovalchuk
Antonov Company, Kyiv, Ukraine
3 shared publications - Orest P. Ostash
Karpenko Physico-Mechanical Institute of the National Academy of Sciences of Ukraine, Lviv, Ukraine
3 shared publications - R. V. Chepil'
Karpenko Physico-Mechanical Institute of the National Academy of Sciences of Ukraine, Lviv, Ukraine
2 shared publications - Sergey Romualdovich Ignatovich
National University "Kyiv Aviation Institute
2 shared publications - A. Antonov
Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine
1 shared publication - Alyona Merkulova
Інститут проблем машинобудування ім. А. М. Підгорного НАН України
1 shared publication
Latest Publications
- Open Access
- 27 August 2025
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 4sup1,p. 132-138
Вплив варіацій пружних характеристик матеріалу на розрахункові характеристики напружено-деформованого стану конструкції
Aluminium alloys are key materials in the aerospace industry because of their combination of low density, high specific strength, and excellent corrosion resistance. Metals are generally considered isotropic materials, exhibiting uniform mechanical properties in all directions. However, plastic deformation processes, such as rolling, can induce texture formation, whereby crystallographic grains align along the direction of deformation. This leads to planar anisotropy, which significantly affects the mechanical behavior of the material under service loads. This study investigates how variations in elastic properties – Young's modulus E and Poisson's ratio μ – affect the stress–strain state (SSS) of a 1163 ATB aluminium alloy sheet structure. A literature review was conducted on analyze the effect of anisotropy on the mechanical properties of specimens cut at various angles to the rolling direction. This confirmed the dependence of the elastic parameters on the orientation. This study presents laboratory test results for Poisson’s ratio in the longitudinal and transverse directions. The experimental data obtained were implemented in finite element modelling to assess the influence of anisotropy on the stress and strain distribution in typical thin-walled structural elements. Modelling was performed using a simplified geometry – a rectangular plate with boundary conditions that simulate real service loads. Nine combinations of elastic parameters were considered to evaluate the sensitivity of the calculated results to variation in these parameters. The analysis revealed that slight changes in the elastic properties can result in significant deviations in SSS, especially in the stress concentration zones. Such deviations considerably impact the assessment of the structural components’ residual strength and durability. Therefore, accounting for anisotropic behavior is critical for improving the accuracy of engineering calculations, particularly in strength and life assessment tasks. Therefore, accounting for anisotropic behavior is critically important to improve the accuracy of engineering calculations, particularly in tasks involving strength and life assessment. The obtained results are recommended for use in modelling, designing, and verifying aerospace components.
- 27 August 2025
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 4sup1,p. 132-138
Open AccessВплив варіацій пружних характеристик матеріалу на розрахункові характеристики напружено-деформованого стану конструкції
Aluminium alloys are key materials in the aerospace industry because of their combination of low density, high specific strength, and excellent corrosion resistance. Metals are generally considered isotropic materials, exhibiting uniform mechanical properties in all directions. However, plastic deformation processes, such as rolling, can induce texture formation, whereby crystallographic grains align along the direction of deformation. This leads to planar anisotropy, which significantly affects the mechanical behavior of the material under service loads. This study investigates how variations in elastic properties – Young's modulus E and Poisson's ratio μ – affect the stress–strain state (SSS) of a 1163 ATB aluminium alloy sheet structure. A literature review was conducted on analyze the effect of anisotropy on the mechanical properties of specimens cut at various angles to the rolling direction. This confirmed the dependence of the elastic parameters on the orientation. This study presents laboratory test results for Poisson’s ratio in the longitudinal and transverse directions. The experimental data obtained were implemented in finite element modelling to assess the influence of anisotropy on the stress and strain distribution in typical thin-walled structural elements. Modelling was performed using a simplified geometry – a rectangular plate with boundary conditions that simulate real service loads. Nine combinations of elastic parameters were considered to evaluate the sensitivity of the calculated results to variation in these parameters. The analysis revealed that slight changes in the elastic properties can result in significant deviations in SSS, especially in the stress concentration zones. Such deviations considerably impact the assessment of the structural components’ residual strength and durability. Therefore, accounting for anisotropic behavior is critical for improving the accuracy of engineering calculations, particularly in strength and life assessment tasks. Therefore, accounting for anisotropic behavior is critically important to improve the accuracy of engineering calculations, particularly in tasks involving strength and life assessment. The obtained results are recommended for use in modelling, designing, and verifying aerospace components.
- 1 July 2024
- Published by Springer Nature in Materials Science
- Vol. 60 (1) , 7-12
Assessment of 1161at aluminum alloy susceptibility to operational degradation
- 1 July 2024
- Published by Springer Nature in Materials Science
- Vol. 60 (1) , 7-12
Assessment of 1161at aluminum alloy susceptibility to operational degradation
- 27 February 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Physicochemical Mechanics of Materials
- Vol. 60 (1) , 12-17
Assessment of 1161АТ aluminum alloy susceptibility to operational degradation
Structure, physicоmechanical characteristics, and fracture micromechanisms under static and cyclic loading of samples cut from clad 2 mm thick sheet made of 1161АT alloy of the Al-Cu-Mg-Mn-Zr system with a reduced content of Si and Fe (up to 0.1 wt% of each) were studied. This alloy in the initial state (quenching and natural aging) and after the influence of termomechanical factor in laboratory conditions which simulate the effects of operational ones were investigated. The 1161AT alloy shows practically the same service characteristics in the initial state and after model degradation, contrary to similar alloys with an increased content of Si and Fe impurities (up to 0.5 wt% of each).
- 27 February 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Physicochemical Mechanics of Materials
- Vol. 60 (1) , 12-17
Assessment of 1161АТ aluminum alloy susceptibility to operational degradation
Structure, physicоmechanical characteristics, and fracture micromechanisms under static and cyclic loading of samples cut from clad 2 mm thick sheet made of 1161АT alloy of the Al-Cu-Mg-Mn-Zr system with a reduced content of Si and Fe (up to 0.1 wt% of each) were studied. This alloy in the initial state (quenching and natural aging) and after the influence of termomechanical factor in laboratory conditions which simulate the effects of operational ones were investigated. The 1161AT alloy shows practically the same service characteristics in the initial state and after model degradation, contrary to similar alloys with an increased content of Si and Fe impurities (up to 0.5 wt% of each).
- 29 November 2022
- Published by Springer Nature
- p. 456-465
Two-Stage Optimization of Laminated Composite Elements with Minimal Mass
- 29 November 2022
- Published by Springer Nature
- p. 456-465
Two-Stage Optimization of Laminated Composite Elements with Minimal Mass
- 27 August 2021
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 4sup2,p. 62-70
Влияние антикоррозионных пленкообразующих составов на усталость авиационных конструкций. Обзор исследований
Corrosion of aircraft structures is one of the main factors limiting the duration of their operation, affecting on the economic efficiency and safety of air transport. Corrosion protection is performed at the stage of manufacturing aircraft structures, during their repair and operation. One of the additional measures of anti-corrosion protection is the use of film-forming coatings, which displace moisture from the gaps of structural joints, form a protective film, and also slow down the corrosion process. The protective properties of film-forming coatings are investigated by standard corrosion tests. At the same time, the specifics of aircraft structures and the possible side effects of the use of anti-corrosion compounds require special studies. The article presents an analysis of works in which the effect of film-forming anticorrosive compounds on the fatigue of elements of aircraft structures is considered.The main type of joints in the structure of modern aircraft are riveted joints. The high penetrating ability of film-forming materials ensures their penetration into the gaps of riveted joints, which, in some cases, can affect the frictional forces between the connected elements, which ensure the integrity of the joints. In some experimental investigations, the influence of film-forming compositions on the kinetics of fatigue crack growth is noted as a side effect. A number of possible mechanisms of deceleration and acceleration of the rate of crack propagation are considered. Experimental data concerning the effect of anticorrosive compounds on the fatigue of riveted joints and the process of propagation of fatigue cracks in structural materials, indicate the need to develop a universal methodology for the selection and use of film-forming compositions for the protection of aircraft structures from corrosion, taking into account the minimization or prevention of negative side effects on the service life of aircraft.
- 27 August 2021
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 4sup2,p. 62-70
Влияние антикоррозионных пленкообразующих составов на усталость авиационных конструкций. Обзор исследований
Corrosion of aircraft structures is one of the main factors limiting the duration of their operation, affecting on the economic efficiency and safety of air transport. Corrosion protection is performed at the stage of manufacturing aircraft structures, during their repair and operation. One of the additional measures of anti-corrosion protection is the use of film-forming coatings, which displace moisture from the gaps of structural joints, form a protective film, and also slow down the corrosion process. The protective properties of film-forming coatings are investigated by standard corrosion tests. At the same time, the specifics of aircraft structures and the possible side effects of the use of anti-corrosion compounds require special studies. The article presents an analysis of works in which the effect of film-forming anticorrosive compounds on the fatigue of elements of aircraft structures is considered.The main type of joints in the structure of modern aircraft are riveted joints. The high penetrating ability of film-forming materials ensures their penetration into the gaps of riveted joints, which, in some cases, can affect the frictional forces between the connected elements, which ensure the integrity of the joints. In some experimental investigations, the influence of film-forming compositions on the kinetics of fatigue crack growth is noted as a side effect. A number of possible mechanisms of deceleration and acceleration of the rate of crack propagation are considered. Experimental data concerning the effect of anticorrosive compounds on the fatigue of riveted joints and the process of propagation of fatigue cracks in structural materials, indicate the need to develop a universal methodology for the selection and use of film-forming compositions for the protection of aircraft structures from corrosion, taking into account the minimization or prevention of negative side effects on the service life of aircraft.
- Open Access
- 1 January 2020
- Published by Ternopil Ivan Puluj National Technical University in Scientific journal of the Ternopil national technical university
- Vol. 99 (3) , 5-16
Fatigue crack growth in aluminum alloy from cold expanded hole with preexisting crack
The fatigue life of aircraft structure elements with operational damage in the vicinity of the hole was investigated. The plates 60 mm wide and 6 mm thick made of D16chT aluminum alloy with a central hole were taken for the study. Fatigue damage was examined with an corner quarter-elliptical fatigue crack with a length of 1,25 mm, which was initiated from an edge notch of 0,5 x 0,5 mm. The fatigue crack growth rate on the surface of the plate after mandrel hole with cold expansion degree i = 2,7% increases up to15 times and residual lifetime in three times compared to the virgin plate.
- 1 January 2020
- Published by Ternopil Ivan Puluj National Technical University in Scientific journal of the Ternopil national technical university
- Vol. 99 (3) , 5-16
Open AccessFatigue crack growth in aluminum alloy from cold expanded hole with preexisting crack
The fatigue life of aircraft structure elements with operational damage in the vicinity of the hole was investigated. The plates 60 mm wide and 6 mm thick made of D16chT aluminum alloy with a central hole were taken for the study. Fatigue damage was examined with an corner quarter-elliptical fatigue crack with a length of 1,25 mm, which was initiated from an edge notch of 0,5 x 0,5 mm. The fatigue crack growth rate on the surface of the plate after mandrel hole with cold expansion degree i = 2,7% increases up to15 times and residual lifetime in three times compared to the virgin plate.
- 7 March 2017
- Published by Taylor & Francis in Research in Nondestructive Evaluation
- Vol. 29 (3) , 156-166
Evaluation of Aluminium Alloys Degradation in Aging Aircraft
- 7 March 2017
- Published by Taylor & Francis in Research in Nondestructive Evaluation
- Vol. 29 (3) , 156-166
Evaluation of Aluminium Alloys Degradation in Aging Aircraft