YKYutaka Kaneko

Yutaka Kaneko

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Yutaka Kaneko has a total of 33 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • In Situ Synthesis of Poly(3,4‐Ethylenedioxythiophene) Analog Using Plasma Inside a Bubble

    by Yutaka Kaneko, Satoru Kawai, Kosuke Ishibashi, Hiroshi Yabu, Hidemasa Takana

    Poly(3,4‐ethylenedioxythiophene) (PEDOT) is one of the most successful conductive polymers. This study proposes a novel in situ synthesis method for water‐dispersible and conductive oligomeric PEDOT analogs (a‐PEDOT) utilizing plasma generated inside a bubble in an EDOT emulsion. Highly oxidative species generated by the plasma initiate polymerization, introducing hydrophilic groups and inducing hole doping. These reactions were found to progress continuously over a 7‐day period due to the presence of long‐lived oxidants such as H 2 O 2 dissolved in the emulsion. The introduction of O 2 into the plasma‐forming gas significantly promoted polymerization and the formation of polaronic oligomeric a‐PEDOT, resulting in enhanced film conductivity. However, under a constant applied voltage, an excessive O 2 supply led to a decrease in conductivity.

  • Modeling and simulation of time dependent ion migration process and bending of ion-doped rubber films using a minimal set of physically estimated parameters

    by Yutaka Kaneko, Gildas Coativy, Joël Courbon, Gaël Sebald, Hidemasa Takana, Jean-Yves Cavaillé

    Films of soft polymers, i.e. above their glass transition temperature, when doped with ionic electric charges, exhibit mechanical deformations such as bending when subjected to an electric field. Previous studies have shown the drift of positive and negative ions, generating a current in the film, is responsible for such deformations due to differences in their diffusion coefficients. In this study, a numerical model is developed to reproduce both the current density and bending behavior of electroactive polymers and to clarify the underlying mechanism. The proposed model consists of two steps. First, the Poisson–Nernst–Planck equations are solved to obtain ion concentration distributions caused by drift and diffusion. From these, the electrostatic energy density distribution is calculated, which induces Maxwell stress within the film. Second, the resulting bending deformation is calculated based on this stress. The simulation results show good agreement with experimental data for both current density and bending behavior. Upon field application, ions migrate in opposite directions, forming electric double layers (EDLs) near the electrodes and ion depletion layers (IDLs) adjacent to the EDLs. The bending behavior is governed by the imbalance in electrostatic energy density around IDLs between the left- and right-hand side originating from differences in ion diffusion coefficients. Furthermore, simulations of specific electric field sequences reveal that incomplete ion diffusion during electric field interruptions cause a ‘memory effect’, wherein current density and bending profiles resume from the point where the electric field was interrupted.

  • Open Access

    Spatiotemporal surface potential mapping and principal-component modes in surface dielectric barrier discharges: towards data-driven reconstruction of induced wall jets

    by Atsushi Komuro, Takuma Uemura, Yutaka Kaneko, Hiroyuki Nishida

    Surface dielectric barrier discharge actuators are widely studied for aerodynamic flow control; however, the quantitative link between surface charge dynamics and induced flow remains unclear. This study combines time-resolved Pockels-effect imaging of the surface potential with particle image velocimetry of the wall jet to clarify the flow induction mechanism in O 2 , air, and N 2 at 1 kHz and 8 kVpp. Principal component analysis decomposes the measured potential field into a voltage-synchronous (deterministic) component and a discharge-driven, cycle-to-cycle fluctuating component; the variance of the fluctuating component is largest in air (≈6.9%), followed by N 2 (≈5.9%) and O 2 (≈4.4%). Wall-normal electric-field metrics derived from the Pockels data reveal two characteristic electrical footprints: a near-wall spike linked to the discharge-driven fluctuations and a mid-layer plateau corresponding to the cycle-mean field, interpreted as a ‘near-wall impulse’ and a ‘quasi-steady drive’, respectively. These electrical footprints explain the observed gas trends: air sustains the strongest and widest wall jet, whereas O 2 and N 2 are broadly comparable, with O 2 occasionally exceeding N 2 in the outer shear layer. A Suzen-type reconstruction using the measured potential as boundary data captures the near-wall localisation and footprint width of the body-force distribution, while highlighting that absolute force levels require volumetric charge transport information beyond surface-field metrics. This framework provides an optically derived, gas-resolved diagnostic for actuator body force estimation, advancing data-driven plasma actuator design and control.

  • Open Access

    Enhanced CO2 selective absorption by opposing ionic liquid electrospray

    by Yutaka Kaneko, Yusuke Onodera, Takashi Makino, Mitsuhiro Kanakubo, Hidemasa Takana


  • The Combination of Rear Flaps and Plasma Actuators for the Drag Reduction of a Square-Back Bluff Body

    by Yutaka Kaneko, Shūji Ōtomo, Taisuke Torin, Yusuke Kakuya, Takafumi Saito, Tatsuhiko Hanai, Takashi Matsuno, Hiroyuki Nishida

    There is a significant need to reduce the aerodynamic drag of ground vehicles. As a result, the active and passive methods of flow control around bluff bodies have been extensively studied to improve aerodynamic performance. In this study, the drag reduction by combining rear flaps and plasma actuators (PAs) is experimentally investigated. PAs are modern active flow control devices that leverage nonthermal plasma, whereas flaps are traditional passive flow control devices. Flaps and PAs are mounted on the square back of the truck model, and the effect of the flap mounting locations (top or side of the model), flap angle, and flap length are investigated at ReH=1.58×105. For both top and side flaps, the longer flaps result in greater drag reduction compared to shorter flaps in the absence of PA actuation. However, additional drag reduction with PA actuation is minimal for the longer flaps, and the flap angle at which drag reaches a local minimum remained unchanged. This is attributed to an increase in pressure drag on the flap as the flap angle increases when the flow is attached to the flap surface. In contrast, PA actuation with shorter flaps demonstrates drag reduction, due to the smaller surface area of the flaps. These results suggest that optimizing the flap angle and length is a promising strategy to maximize the aerodynamic benefits of PA actuation and reduce the drag on bluff bodies.


  • Phased Demonstrations of MBSE in Small Demonstration Satellite Series: Development of System Model and Environment for Full Application of MBSE

    by Atsushi Wada, Yutaka Komatsu, Daiki Tate, Haruhi Katsumata, Yoji Shirasawa, Keiichiro Fujimoto, Yuya Kakehashi, Kengo Nakamura, Yutaka Kaneko, Shinichi Suzuki, et al.

    The Japan Aerospace Exploration Agency (JAXA) has been implementing phased and progressive demonstrations of the Model‐Based Systems Engineering (MBSE) applications, using small demonstration satellite series, so called the Rapid Innovative Payload Demonstration Satellite (RAISE), as a demonstration pre‐cursor. The purpose of the activity is to establish a practical methodology of the MBSE application to satellite projects, to promote its practices, and to infuse MBSE to the Japanese space community. These RAISE satellites are 100kg‐class flagships in the Innovative Satellite Technology Demonstration Program, which provides on‐orbit demonstration opportunities for new technologies and key‐components. This paper presents the phased demonstration strategy, an overall approach, and the technology development of a system model being built for the full application of MBSE to RAISE‐4. For the technology development, the paper covers framework, modeling scope, system model building, system model collaboration with analysis/simulation tool, introduction of design rationale and concerns, information sharing through OpenMBEE, for our full application of MBSE.


  • Open Access

    Comparison between Density and Velocity Fields in Burst Modulation of a Dielectric-Barrier-Discharge Plasma Actuator

    by Kenta Emori, Yutaka Kaneko, Hiroyuki Nishida

    The flow field produced by a dielectric-barrier-discharge plasma actuator using burst modulation was experimentally investigated in quiescent air from two viewpoints: density and vorticity fields. A wide range of burst signal parameters were evaluated using particle-image velocimetry and background-oriented schlieren measurements. Four types of flow-field patterns were found: Type 1 was a wall jet, similar to continuous operation; Type 2 was a periodical, independent vortex moving along the wall surface; Types 3 and 4 demonstrated a feature wherein the periodic shedding of the vortex pair (primary and secondary vortices) occurred while moving over the surface. While Types 3 and 4 demonstrated a shared feature, they had different density and vorticity structures. The change of the flow-field pattern from Type 1 to Type 4 was triggered by a lower burst frequency and ratio, as well as a higher base frequency. In addition, the vorticity strength and density were strongly negatively correlated and depended on the rate of power consumption to generate one vortex.


  • Classification of flow-field patterns in burst-mode actuation of a dielectric-barrier-discharge plasma actuator

    by Kenta Emori, Yutaka Kaneko, Hiroyuki Nishida

    This study investigates the characteristics of flow-field patterns generated by burst-mode actuation of a dielectric-barrier-discharge plasma actuator in quiescent air. Particle-image velocimetry and background-oriented schlieren measurements conducted over a wide range of burst-signal parameters show that there are three types of flow-field patterns. Type 1 is the wall-surface jet seen in continuous mode actuation; type 2 features periodical independent vortices traveling along the wall surface; type 3 features such vortices moving away from the surface. The vortex sizes in types 2 and 3 are proportional to the energy consumed in generating one vortex. When the time-averaged jet velocity estimated by the power consumption is used as the characteristic velocity in the nondimensional scaling law, the time profiles of the vortex location in the type 3 flow-field pattern collapse into a single line, independently of the burst frequency and ratio. However, in the initial phase, the nondimensional vortex-core motion is better described using the jet velocity in continuous-mode actuation as the characteristic velocity. The transitions of the flow-field pattern from type 1 to type 3 result from interference between cyclically generated vortices and depend on the inter-vortex distances and the energy consumed in generating one vortex.


  • Open Access

    Visualization of the Electrohydrodynamic and Thermal Effects of AC-DBD Plasma Actuators of Plate- and Wire-Exposed Electrodes

    by Yutaka Kaneko, Hiroyuki Nishida, Yoshiyuki Tagawa

    The dielectric barrier discharge plasma actuator is a promising flow control device that uses surface discharge. The actuator generates an electrohydrodynamic force and Joule heating that contribute to the flow control. Thus, it is important to investigate the electrohydrodynamic and thermal effects on the air flow. To this end, the flow velocity field, density field, and surface temperature distribution induced by an alternating current dielectric barrier discharge plasma actuator were experimentally examined, adopting particle image velocimetry, the background oriented schlieren technique, and an infrared camera. These experiments were conducted for plate- and wire-exposed electrode plasma actuators to investigate the effect of the shape of the exposed electrode. It was confirmed that the topology of the discharge is different between the two types of plasma actuators. This results in a difference in the spatial distributions of the velocity and density fields between the two actuators. In particular, we clarified that there is an obvious difference in the peak position of the density and temperature distribution between the two actuators. We also confirmed that the difference in the spatial distribution of the vertical velocity makes the above difference.