Kenta Emori
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Kenta Emori has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Hiroyuki Nishida
Department of Mechanical Systems Engineering, Tokyo University of Agriculture and Technology, Tokyo 184-8588, Japan
4 shared publications - Asami Hatamoto
Department of Mechanical Systems Engineering, Tokyo University of Agriculture and Technology, Koganei, Tokyo 184-8588, Japan
2 shared publications - Yutaka Kaneko
Institute of Fluid Science Tohoku University Sendai Japan
2 shared publications
Latest Publications
- 3 August 2023
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 56 (44) , 449501
Corrigendum: Surface temperature characterization of dielectric barrier discharge plasma actuator in quiescent air (2023 J. Phys. D: Appl. Phys. 56 155203)
- 3 August 2023
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 56 (44) , 449501
Corrigendum: Surface temperature characterization of dielectric barrier discharge plasma actuator in quiescent air (2023 J. Phys. D: Appl. Phys. 56 155203)
- 13 March 2023
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 56 (15) , 155203
Surface temperature characterization of dielectric barrier discharge plasma actuator in quiescent air
Dielectric barrier discharge plasma actuators (DBDPAs) have been investigated for active flow control. The discharge induces ionic wind, which can be utilized for flow control; however, it simultaneously heats the flow and the dielectric surface. The thermal characteristics of the DBDPA must be clarified for applications in thermo-fluid engineering, such as forced convective cooling. In this study, we constructed a similarity law for the time variation of the surface temperature, assuming that the induced flow was heated by the discharge and that the dielectric was heated by the airflow. The similarity law was derived from the one-dimensional heat conduction equation in the dielectric, and the spatially averaged normalized temperature was then formulated as a function of the Biot and Fourier numbers. To experimentally validate the similarity law, the surface temperature, thrust, and power consumption were measured. The induced flow temperature and heat transfer coefficient were estimated based on the thrust and power consumption. The measured results verified that the similarity law was valid, regardless of the dielectric material, thickness, or applied voltage. This result supports the hypothesis regarding the heating mechanism in which the airflow is heated by Joule heating and the dielectric is heated by forced convection.
- 13 March 2023
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 56 (15) , 155203
Surface temperature characterization of dielectric barrier discharge plasma actuator in quiescent air
Dielectric barrier discharge plasma actuators (DBDPAs) have been investigated for active flow control. The discharge induces ionic wind, which can be utilized for flow control; however, it simultaneously heats the flow and the dielectric surface. The thermal characteristics of the DBDPA must be clarified for applications in thermo-fluid engineering, such as forced convective cooling. In this study, we constructed a similarity law for the time variation of the surface temperature, assuming that the induced flow was heated by the discharge and that the dielectric was heated by the airflow. The similarity law was derived from the one-dimensional heat conduction equation in the dielectric, and the spatially averaged normalized temperature was then formulated as a function of the Biot and Fourier numbers. To experimentally validate the similarity law, the surface temperature, thrust, and power consumption were measured. The induced flow temperature and heat transfer coefficient were estimated based on the thrust and power consumption. The measured results verified that the similarity law was valid, regardless of the dielectric material, thickness, or applied voltage. This result supports the hypothesis regarding the heating mechanism in which the airflow is heated by Joule heating and the dielectric is heated by forced convection.
- Open Access
Comparison between Density and Velocity Fields in Burst Modulation of a Dielectric-Barrier-Discharge Plasma Actuator
The flow field produced by a dielectric-barrier-discharge plasma actuator using burst modulation was experimentally investigated in quiescent air from two viewpoints: density and vorticity fields. A wide range of burst signal parameters were evaluated using particle-image velocimetry and background-oriented schlieren measurements. Four types of flow-field patterns were found: Type 1 was a wall jet, similar to continuous operation; Type 2 was a periodical, independent vortex moving along the wall surface; Types 3 and 4 demonstrated a feature wherein the periodic shedding of the vortex pair (primary and secondary vortices) occurred while moving over the surface. While Types 3 and 4 demonstrated a shared feature, they had different density and vorticity structures. The change of the flow-field pattern from Type 1 to Type 4 was triggered by a lower burst frequency and ratio, as well as a higher base frequency. In addition, the vorticity strength and density were strongly negatively correlated and depended on the rate of power consumption to generate one vortex.
Open AccessComparison between Density and Velocity Fields in Burst Modulation of a Dielectric-Barrier-Discharge Plasma Actuator
The flow field produced by a dielectric-barrier-discharge plasma actuator using burst modulation was experimentally investigated in quiescent air from two viewpoints: density and vorticity fields. A wide range of burst signal parameters were evaluated using particle-image velocimetry and background-oriented schlieren measurements. Four types of flow-field patterns were found: Type 1 was a wall jet, similar to continuous operation; Type 2 was a periodical, independent vortex moving along the wall surface; Types 3 and 4 demonstrated a feature wherein the periodic shedding of the vortex pair (primary and secondary vortices) occurred while moving over the surface. While Types 3 and 4 demonstrated a shared feature, they had different density and vorticity structures. The change of the flow-field pattern from Type 1 to Type 4 was triggered by a lower burst frequency and ratio, as well as a higher base frequency. In addition, the vorticity strength and density were strongly negatively correlated and depended on the rate of power consumption to generate one vortex.
- 1 February 2022
- Published by AIP Publishing in Physics of Fluids
- Vol. 34 (2) , 023601
Classification of flow-field patterns in burst-mode actuation of a dielectric-barrier-discharge plasma actuator
This study investigates the characteristics of flow-field patterns generated by burst-mode actuation of a dielectric-barrier-discharge plasma actuator in quiescent air. Particle-image velocimetry and background-oriented schlieren measurements conducted over a wide range of burst-signal parameters show that there are three types of flow-field patterns. Type 1 is the wall-surface jet seen in continuous mode actuation; type 2 features periodical independent vortices traveling along the wall surface; type 3 features such vortices moving away from the surface. The vortex sizes in types 2 and 3 are proportional to the energy consumed in generating one vortex. When the time-averaged jet velocity estimated by the power consumption is used as the characteristic velocity in the nondimensional scaling law, the time profiles of the vortex location in the type 3 flow-field pattern collapse into a single line, independently of the burst frequency and ratio. However, in the initial phase, the nondimensional vortex-core motion is better described using the jet velocity in continuous-mode actuation as the characteristic velocity. The transitions of the flow-field pattern from type 1 to type 3 result from interference between cyclically generated vortices and depend on the inter-vortex distances and the energy consumed in generating one vortex.
- 1 February 2022
- Published by AIP Publishing in Physics of Fluids
- Vol. 34 (2) , 023601
Classification of flow-field patterns in burst-mode actuation of a dielectric-barrier-discharge plasma actuator
This study investigates the characteristics of flow-field patterns generated by burst-mode actuation of a dielectric-barrier-discharge plasma actuator in quiescent air. Particle-image velocimetry and background-oriented schlieren measurements conducted over a wide range of burst-signal parameters show that there are three types of flow-field patterns. Type 1 is the wall-surface jet seen in continuous mode actuation; type 2 features periodical independent vortices traveling along the wall surface; type 3 features such vortices moving away from the surface. The vortex sizes in types 2 and 3 are proportional to the energy consumed in generating one vortex. When the time-averaged jet velocity estimated by the power consumption is used as the characteristic velocity in the nondimensional scaling law, the time profiles of the vortex location in the type 3 flow-field pattern collapse into a single line, independently of the burst frequency and ratio. However, in the initial phase, the nondimensional vortex-core motion is better described using the jet velocity in continuous-mode actuation as the characteristic velocity. The transitions of the flow-field pattern from type 1 to type 3 result from interference between cyclically generated vortices and depend on the inter-vortex distances and the energy consumed in generating one vortex.