M. Mohsin Raza
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
M. Mohsin Raza has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Yu-Lung Lo
Department of Mechanical Engineering, National Cheng Kung University, Tainan, Taiwan
3 shared publications - Amir Reza Ansari Dezfoli
Department of Mechanical Engineering, National Cheng Kung University, Tainan 701401, Taiwan
2 shared publications Yu-Lung Lo
Department of Mechanical Engineering, National Cheng Kung University, No.1 Daxue Rd., East Dist., Tainan City 701, Taiwan
2 shared publicationsAmir Reza Ansari Dezfoli
Department of Mechanical Engineering, National Cheng Kung University, No.1 Daxue Rd., East Dist., Tainan City 701, Taiwan
1 shared publication- Chia-Hung Hung
National Cheng Kung University Department of Mechanical Engineering Tainan
1 shared publication Yi-Cheng Lin
National Cheng Kung University Department of Mechanical Engineering Tainan
1 shared publication
Latest Publications
- 18 November 2024
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 147 (3) , 1-28
Optimizing 3D Laser Foil Printing Parameters for AA 6061: Numerical and Experimental Analysis
This study utilizes a technology known as 3D laser foil printing (LFP) to create precise structures by layering metal foils using birutoto welding. Metal foils have the advantages of rapid cooling and efficient heat conduction, allowing for the formation of fine-grained structures. However, when dealing with materials like aluminum alloys in laser processes, defects can arise as a result of their high reflectivity. To address this challenge, laser circular oscillation welding (LCOW) is applied to the LFP process. LCOW's circular motions with higher scanning frequencies widen the keyholes and reduce some defects such as spattering, bubble formation, and microcracks. Simulation predictions with an error margin of approximately 10% in comparison to experimental results demonstrate the reliability of the model. Furthermore, the study integrates circular packing design with artificial neural networks to create comprehensive processing maps tailored to different criteria for extracting optimal welding parameters. As a result, for the optimized processing parameters screened using the above systematic process, no cracks were observed on the upper surface of the 3D LFP parts produced with a laser power of 800 W and a scanning speed of 550 mm/s, and only 0.12% porosity was observed from the cross section of the sample. Future research will focus on incorporating simulation results to model microstructures more precisely and continually refining LCOW parameters as new materials and technologies emerge, ensuring the ongoing enhancement of weld quality in the 3D LFP process.
- 18 November 2024
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 147 (3) , 1-28
Optimizing 3D Laser Foil Printing Parameters for AA 6061: Numerical and Experimental Analysis
This study utilizes a technology known as 3D laser foil printing (LFP) to create precise structures by layering metal foils using birutoto welding. Metal foils have the advantages of rapid cooling and efficient heat conduction, allowing for the formation of fine-grained structures. However, when dealing with materials like aluminum alloys in laser processes, defects can arise as a result of their high reflectivity. To address this challenge, laser circular oscillation welding (LCOW) is applied to the LFP process. LCOW's circular motions with higher scanning frequencies widen the keyholes and reduce some defects such as spattering, bubble formation, and microcracks. Simulation predictions with an error margin of approximately 10% in comparison to experimental results demonstrate the reliability of the model. Furthermore, the study integrates circular packing design with artificial neural networks to create comprehensive processing maps tailored to different criteria for extracting optimal welding parameters. As a result, for the optimized processing parameters screened using the above systematic process, no cracks were observed on the upper surface of the 3D LFP parts produced with a laser power of 800 W and a scanning speed of 550 mm/s, and only 0.12% porosity was observed from the cross section of the sample. Future research will focus on incorporating simulation results to model microstructures more precisely and continually refining LCOW parameters as new materials and technologies emerge, ensuring the ongoing enhancement of weld quality in the 3D LFP process.
- Open Access
3D Multi-Track and Multi-Layer Epitaxy Grain Growth Simulations of Selective Laser Melting
An integrated simulation framework consisting of the 3D finite element method and 3D cellular automaton method is presented for simulating the multi-track and multi-layer selective laser melting (SLM) process. The framework takes account of all the major multi-physics phenomena in the SLM process, including the initial grain structure, the growth kinetics, the laser scanning strategy, the laser–powder and laser–matter interactions, the melt flow, and the powder-to-liquid-to-solid transformations. The feasibility of the proposed framework is demonstrated by simulating the evolution of the epitaxy grain structure of Inconel 718 (IN718) during a 15-layer SLM process performed using a bi-directional 67° rotation scanning strategy and various SLM process parameters. The simulation results are found to be in good agreement with the experimental observations obtained in the present study and in the literature. In particular, a strong (001) texture is observed in the final component, which indicates that the grains with a preferred orientation win the competitive epitaxy grain growth process. In addition, the size and shape of the IN718 grains are governed primarily by the cooling rate, where the cooling rate is determined in turn by the SLM parameters and the build height. Overall, the results show that the proposed framework provides an accurate approach for predicting the final microstructures of SLM components, and therefore, it can play an important role in optimizing the SLM processing parameters in such a way as to produce components with the desired mechanical properties.
Open Access3D Multi-Track and Multi-Layer Epitaxy Grain Growth Simulations of Selective Laser Melting
An integrated simulation framework consisting of the 3D finite element method and 3D cellular automaton method is presented for simulating the multi-track and multi-layer selective laser melting (SLM) process. The framework takes account of all the major multi-physics phenomena in the SLM process, including the initial grain structure, the growth kinetics, the laser scanning strategy, the laser–powder and laser–matter interactions, the melt flow, and the powder-to-liquid-to-solid transformations. The feasibility of the proposed framework is demonstrated by simulating the evolution of the epitaxy grain structure of Inconel 718 (IN718) during a 15-layer SLM process performed using a bi-directional 67° rotation scanning strategy and various SLM process parameters. The simulation results are found to be in good agreement with the experimental observations obtained in the present study and in the literature. In particular, a strong (001) texture is observed in the final component, which indicates that the grains with a preferred orientation win the competitive epitaxy grain growth process. In addition, the size and shape of the IN718 grains are governed primarily by the cooling rate, where the cooling rate is determined in turn by the SLM parameters and the build height. Overall, the results show that the proposed framework provides an accurate approach for predicting the final microstructures of SLM components, and therefore, it can play an important role in optimizing the SLM processing parameters in such a way as to produce components with the desired mechanical properties.
- Open Access
Prediction of Epitaxial Grain Growth in Single-Track Laser Melting of IN718 Using Integrated Finite Element and Cellular Automaton Approach
The mechanical properties of selective laser melting (SLM) components are fundamentally dependent on their microstructure. Accordingly, the present study proposes an integrated simulation framework consisting of a three-dimensional (3D) finite element model and a cellular automaton model for predicting the epitaxial grain growth mode in the single-track SLM processing of IN718. The laser beam scattering effect, melt surface evolution, powder volume shrinkage, bulk heterogeneous nucleation, epitaxial growth, and initial microstructure of the substrate are considered. The simulation results show that during single-track SLM processing, coarse epitaxial grains are formed at the melt–substrate interface, while fine grains grow at the melt–powder interface with a density determined by the intensity of the heat input. During the solidification stage, the epitaxial grains and bulk nucleated grains grow toward the top surface of the melt pool along the temperature gradient vectors. The rate of the epitaxial grain growth varies as a function of the orientation and size of the partially melted grains at the melt–substrate boundary, the melt pool size, and the temperature gradient. This is observed that by increasing heat input from 250 J/m to 500 J/m, the average grain size increases by ~20%. In addition, the average grain size reduces by 17% when the initial substrate grain size decreases by 50%. In general, the results show that the microstructure of the processed IN718 alloy can be controlled by adjusting the heat input, preheating conditions, and initial substrate grain size.
Open AccessPrediction of Epitaxial Grain Growth in Single-Track Laser Melting of IN718 Using Integrated Finite Element and Cellular Automaton Approach
The mechanical properties of selective laser melting (SLM) components are fundamentally dependent on their microstructure. Accordingly, the present study proposes an integrated simulation framework consisting of a three-dimensional (3D) finite element model and a cellular automaton model for predicting the epitaxial grain growth mode in the single-track SLM processing of IN718. The laser beam scattering effect, melt surface evolution, powder volume shrinkage, bulk heterogeneous nucleation, epitaxial growth, and initial microstructure of the substrate are considered. The simulation results show that during single-track SLM processing, coarse epitaxial grains are formed at the melt–substrate interface, while fine grains grow at the melt–powder interface with a density determined by the intensity of the heat input. During the solidification stage, the epitaxial grains and bulk nucleated grains grow toward the top surface of the melt pool along the temperature gradient vectors. The rate of the epitaxial grain growth varies as a function of the orientation and size of the partially melted grains at the melt–substrate boundary, the melt pool size, and the temperature gradient. This is observed that by increasing heat input from 250 J/m to 500 J/m, the average grain size increases by ~20%. In addition, the average grain size reduces by 17% when the initial substrate grain size decreases by 50%. In general, the results show that the microstructure of the processed IN718 alloy can be controlled by adjusting the heat input, preheating conditions, and initial substrate grain size.
- Open Access
Microstructure and Elements Concentration of Inconel 713LC during Laser Powder Bed Fusion through a Modified Cellular Automaton Model
In this study, a hybrid finite element (FE) and cellular automaton (CA) model is developed to explore crystallization behavior and alloying of Inconel713LC during Laser powder bed fusion. A cellular automaton model is considering the surface nucleation, equiaxed bulk nucleation, and grain growth kinetics. In addition, the equation for solute diffusion is coupled with a cellular automaton model to simulate the IN713LC elements segregation. During the phase change, the non-equilibrium segregation model is applied to insert the effect of ultra-fast solidification happening during LPBF. It is found that, during LPBF processing of IN713LC, the micro segregation of Nb, Ti, and C is accrued at the grain boundaries. It is further shown that the micro segregation intensity depends on the solidification speed, which is determined in turn by the laser heat input. In particular, a lower laser heat input increases the solidification speed and results in a more uniform solid phase, thereby reducing the risk of crack formation. Finally, using a comparison between simulation results and experimental observation, it was shown that the proposed model successfully predicts the bulk element concentration of IN713LC after laser melting.
Open AccessMicrostructure and Elements Concentration of Inconel 713LC during Laser Powder Bed Fusion through a Modified Cellular Automaton Model
In this study, a hybrid finite element (FE) and cellular automaton (CA) model is developed to explore crystallization behavior and alloying of Inconel713LC during Laser powder bed fusion. A cellular automaton model is considering the surface nucleation, equiaxed bulk nucleation, and grain growth kinetics. In addition, the equation for solute diffusion is coupled with a cellular automaton model to simulate the IN713LC elements segregation. During the phase change, the non-equilibrium segregation model is applied to insert the effect of ultra-fast solidification happening during LPBF. It is found that, during LPBF processing of IN713LC, the micro segregation of Nb, Ti, and C is accrued at the grain boundaries. It is further shown that the micro segregation intensity depends on the solidification speed, which is determined in turn by the laser heat input. In particular, a lower laser heat input increases the solidification speed and results in a more uniform solid phase, thereby reducing the risk of crack formation. Finally, using a comparison between simulation results and experimental observation, it was shown that the proposed model successfully predicts the bulk element concentration of IN713LC after laser melting.
- Open Access
- 1 July 2021
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 819
Experimental investigation into microstructure, mechanical properties, and cracking mechanism of IN713LC processed by laser powder bed fusion
- 1 July 2021
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 819
Open AccessExperimental investigation into microstructure, mechanical properties, and cracking mechanism of IN713LC processed by laser powder bed fusion