Alfirano Alfirano
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Alfirano Alfirano has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Galih Senopati
National Research and Innovation Agency
2 shared publications - Albertus Deny Setyawan
Research Center for Metallurgy, National Research and Innovation Agency (BRIN), KST B.J. Habibie, Tangerang Selatan, Banten 15314, Indonesia
1 shared publication Bachtiar Zuhdi Alfarizi
Sultan Ageng Tirtayasa University
1 shared publication- Bambang Hermanto
Research Center for Energy Materials, National Research and Innovation Agency (BRIN), Tangerang Selatan, Indonesia
1 shared publication - Dedi
Research Center for Electronics, National Research and Innovation Agency, Jl. Sangkuriang, Bandung 40135, Indonesia
1 shared publication Djoko Muljono
PT. Krakatau Steel
1 shared publication
Latest Publications
- 31 July 2026
- Published by IOP Publishing in Physica Scripta
- Vol. 101 (31) , 315901
Effect of annealing temperature on the microstructure and thermoelectric properties of TiNiSn 0.9 Al 0.1 half-Heusler alloys
The growing demand for efficient energy-conversion technologies has intensified research into thermoelectric materials capable of harvesting waste heat. This study investigates the effect of annealing temperature on the microstructure and thermoelectric performance of aluminum-doped TiNiSn half-Heusler alloys. TiNiSn 0.9 Al 0.1 samples were synthesized via vacuum arc remelting and annealed at 700 °C, 800 °C, and 900 °C for 168 h. Structural analysis reveals improved phase homogeneity and grain growth with increasing annealing temperature, with near single-phase formation at 800 °C. Transport measurements indicate n-type conduction for all samples, with semiconducting behavior observed at higher annealing temperatures. The sample annealed at 700 °C exhibits the highest Seebeck coefficient and the highest power factor among all investigated samples. Consequently, the highest thermoelectric performance is achieved at 700 °C, with a ZT value of ∼0.27 at 650 K. The present work provides an effective annealing strategy for enhancing the thermoelectric performance of TiNiSn-based materials for medium-temperature energy harvesting applications.
- 31 July 2026
- Published by IOP Publishing in Physica Scripta
- Vol. 101 (31) , 315901
Effect of annealing temperature on the microstructure and thermoelectric properties of TiNiSn 0.9 Al 0.1 half-Heusler alloys
The growing demand for efficient energy-conversion technologies has intensified research into thermoelectric materials capable of harvesting waste heat. This study investigates the effect of annealing temperature on the microstructure and thermoelectric performance of aluminum-doped TiNiSn half-Heusler alloys. TiNiSn 0.9 Al 0.1 samples were synthesized via vacuum arc remelting and annealed at 700 °C, 800 °C, and 900 °C for 168 h. Structural analysis reveals improved phase homogeneity and grain growth with increasing annealing temperature, with near single-phase formation at 800 °C. Transport measurements indicate n-type conduction for all samples, with semiconducting behavior observed at higher annealing temperatures. The sample annealed at 700 °C exhibits the highest Seebeck coefficient and the highest power factor among all investigated samples. Consequently, the highest thermoelectric performance is achieved at 700 °C, with a ZT value of ∼0.27 at 650 K. The present work provides an effective annealing strategy for enhancing the thermoelectric performance of TiNiSn-based materials for medium-temperature energy harvesting applications.
- Open Access
- 15 December 2023
- Published by Brawijaya University in Jurnal Rekayasa Mesin
- Vol. 14 (3) , 1013-1022
UPAYA PERBAIKAN SIFAT MEKANIK BAJA PLAT JOIN G 3131 SPHC MELALUI SIMULASI PROSES INTERCRITICAL ANNEALING DI INDUSTRI KONSTRUKSI BAJA
Improvement of the mechanical properties of G3131 SPHC equivalent to JIS G 3101 SS330 plate joint steel through intercritical annealing simulations has been carried out. The JIS G 3131 grade SPHC steel was gradually heated by intercritical annealing at temperatures of 750–850 oC for holding times of 1–15 minutes. After intercritical annealing treatment, the tensile strength and yield strength of steel increased compared to non-treatment samples. The average tensile strength obtained was 573 MPa with an increase of 76.85% compared to the tensile strength before the intercritical annealing process. Meanwhile, the yield strength of steel increased by 60% to 421 MPa. Increasing the annealing temperature and holding time will promote the formation of the martensite phase, as well as enlarge the austenite and ferrite grains. Optimal heating variable obtained at a temperature of 750 ℃ with a holding time of 15 minutes. Using these variables produced a tensile strength of 625 MPa and a yield strength of 434 MPa with an elongation of 23% which is standardly included in JIS G 3101 SS400.At the optimal value, the grain growth kinetic of K and n values were 0.280466778 and 0.6905, respectively, with an activation energy (Q) of 12.4268517 J/mol.
- 15 December 2023
- Published by Brawijaya University in Jurnal Rekayasa Mesin
- Vol. 14 (3) , 1013-1022
Open AccessUPAYA PERBAIKAN SIFAT MEKANIK BAJA PLAT JOIN G 3131 SPHC MELALUI SIMULASI PROSES INTERCRITICAL ANNEALING DI INDUSTRI KONSTRUKSI BAJA
Improvement of the mechanical properties of G3131 SPHC equivalent to JIS G 3101 SS330 plate joint steel through intercritical annealing simulations has been carried out. The JIS G 3131 grade SPHC steel was gradually heated by intercritical annealing at temperatures of 750–850 oC for holding times of 1–15 minutes. After intercritical annealing treatment, the tensile strength and yield strength of steel increased compared to non-treatment samples. The average tensile strength obtained was 573 MPa with an increase of 76.85% compared to the tensile strength before the intercritical annealing process. Meanwhile, the yield strength of steel increased by 60% to 421 MPa. Increasing the annealing temperature and holding time will promote the formation of the martensite phase, as well as enlarge the austenite and ferrite grains. Optimal heating variable obtained at a temperature of 750 ℃ with a holding time of 15 minutes. Using these variables produced a tensile strength of 625 MPa and a yield strength of 434 MPa with an elongation of 23% which is standardly included in JIS G 3101 SS400.At the optimal value, the grain growth kinetic of K and n values were 0.280466778 and 0.6905, respectively, with an activation energy (Q) of 12.4268517 J/mol.
- Open Access
- 26 August 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (12(112)) , 25-32
The effect of cold rolling and high-temperature gas nitriding on austenite phase formation in AISI 430 SS
Austenitic stainless steel is the most commonly used material in the production of orthopedic prostheses. In this study, AISI 430 SS (0.12 wt. % C; 1 wt. % Si; 1 wt. % Mn; 18 wt. % Cr; 0.04 wt. % P and 0.03 wt. % S) will be modified by creating austenite and removing its ferromagnetic properties via the high-temperature gas nitriding process. Cold rolling with various percentage reduction (30, 50, and 70 %) was followed by gas nitriding at a temperature of 1200 °C with holding times of 5, 7, and 9 hours, then quenching in water was carried out on as-annealed AISI 430 SS. The formation of the austenite phase was examined by XRD (x-ray diffraction). The microstructure and element dispersion were observed using SEM-EDS (scanning electron microscope-energy dispersive spectrometry), whereas the mechanical properties after gas nitriding and water quenching were determined by Vickers microhardness testing. At all stages of the gas nitriding process, the FCC iron indicated the austenite phase was visible on the alloy's surface, although the ferrite phase is still present. The intensity of austenite formation is produced by cold rolling 70 % reduction with a 5-hour gas nitriding time. Furthermore, the nitrogen layer was formed with a maximum thickness layer of approximately 3.14 µm after a 50 % reduction in cold rolling and 9 hours of gas nitriding process followed by water quenching. The hardness reached 600 HVN in this condition. This is due to the distribution of carbon that is concentrated on the surface. As the percent reduction in the cold rolling process increases, the strength of AISI 430 SS after gas nitriding can increase, causing an increase in the number of dislocations. The highest tensile strength and hardness of AISI 430 SS of 669 MPa and 271.83 HVN were obtained with a reduction of 70 %.
- 26 August 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (12(112)) , 25-32
Open AccessThe effect of cold rolling and high-temperature gas nitriding on austenite phase formation in AISI 430 SS
Austenitic stainless steel is the most commonly used material in the production of orthopedic prostheses. In this study, AISI 430 SS (0.12 wt. % C; 1 wt. % Si; 1 wt. % Mn; 18 wt. % Cr; 0.04 wt. % P and 0.03 wt. % S) will be modified by creating austenite and removing its ferromagnetic properties via the high-temperature gas nitriding process. Cold rolling with various percentage reduction (30, 50, and 70 %) was followed by gas nitriding at a temperature of 1200 °C with holding times of 5, 7, and 9 hours, then quenching in water was carried out on as-annealed AISI 430 SS. The formation of the austenite phase was examined by XRD (x-ray diffraction). The microstructure and element dispersion were observed using SEM-EDS (scanning electron microscope-energy dispersive spectrometry), whereas the mechanical properties after gas nitriding and water quenching were determined by Vickers microhardness testing. At all stages of the gas nitriding process, the FCC iron indicated the austenite phase was visible on the alloy's surface, although the ferrite phase is still present. The intensity of austenite formation is produced by cold rolling 70 % reduction with a 5-hour gas nitriding time. Furthermore, the nitrogen layer was formed with a maximum thickness layer of approximately 3.14 µm after a 50 % reduction in cold rolling and 9 hours of gas nitriding process followed by water quenching. The hardness reached 600 HVN in this condition. This is due to the distribution of carbon that is concentrated on the surface. As the percent reduction in the cold rolling process increases, the strength of AISI 430 SS after gas nitriding can increase, causing an increase in the number of dislocations. The highest tensile strength and hardness of AISI 430 SS of 669 MPa and 271.83 HVN were obtained with a reduction of 70 %.
- 30 June 2010
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 654-656, 2176-2179
Phase and Morphology of Carbides in ASTM F75 Co-Cr-Mo-C Alloys Formed at 1473 to 1623 K
The phase and morphology of precipitates in heat-treated Co-28Cr-6Mo-xC (x = 0.12, 0.15, 0.25, and 0.35mass%) alloys were investigated. The as-cast alloys were solution-treated in the temperature range of 1473 to 1623 K for 0 to 43.2 ks. Complete precipitate dissolution was observed in all four alloys, each of which had different carbon contents. The holding time for complete dissolution was greater for alloys with greater carbon content. The curve representing the boundary between the complete- and incomplete-dissolution conditions for each alloy is C shaped. Under the incomplete precipitate dissolution conditions of the Co-28Cr-6Mo-0.25C alloy, an M23C6 type carbide and a π-phase (M2T3X type carbide with β-Mn structure) were observed at 1548 to 1623 K, and starlike precipitates with a stripe pattern and with a dense appearance were both observed; the former comprised the M23C6 type carbide + γ-phase, and the latter was the π-phase. In contrast, only a blocky-dense M23C6 type carbide was observed at 1473 to 1523 K.
- 30 June 2010
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 654-656, 2176-2179
Phase and Morphology of Carbides in ASTM F75 Co-Cr-Mo-C Alloys Formed at 1473 to 1623 K
The phase and morphology of precipitates in heat-treated Co-28Cr-6Mo-xC (x = 0.12, 0.15, 0.25, and 0.35mass%) alloys were investigated. The as-cast alloys were solution-treated in the temperature range of 1473 to 1623 K for 0 to 43.2 ks. Complete precipitate dissolution was observed in all four alloys, each of which had different carbon contents. The holding time for complete dissolution was greater for alloys with greater carbon content. The curve representing the boundary between the complete- and incomplete-dissolution conditions for each alloy is C shaped. Under the incomplete precipitate dissolution conditions of the Co-28Cr-6Mo-0.25C alloy, an M23C6 type carbide and a π-phase (M2T3X type carbide with β-Mn structure) were observed at 1548 to 1623 K, and starlike precipitates with a stripe pattern and with a dense appearance were both observed; the former comprised the M23C6 type carbide + γ-phase, and the latter was the π-phase. In contrast, only a blocky-dense M23C6 type carbide was observed at 1473 to 1523 K.