Fudhail Abdul Munir
Research Subjects
Research Interests
Fudhail Abdul Munir has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Herman Saputro
Universitas Sebelas Maret
2 shared publications - Mohd Juzaila Abd Latif
Universiti Teknikal Malaysia Melaka
2 shared publications - Mohd Shukri Yob
Universiti Teknikal Malaysia Melaka
2 shared publications - Ojo Kurdi
Diponegoro University
2 shared publications - Abdul Rafeq Saleman
Faculty of Mechanical Engineering, Universiti Teknikal Malaysia Melaka, Durian Tunggal, Melaka, Malaysia
1 shared publication Abduljalil Ali Al-Abidi
1 shared publication
Latest Publications
- Open Access
- 29 July 2026
- Published by Elsevier in SSRN Electronic Journal
Impact of Recycled Dehumidified Air via Silica Gel on the performance of a Solar Drying System
Solar drying systems are a promising renewable energy technology that can be used to dry products using solar radiation, and with a lower energy use. One problem, however, is the high humidity of recirculated air that slows water removal and reduces drying efficiency. The use of desiccant materials, especially silica gel, can be an effective solution for desiccant performance and moisture reduction. A hybrid solar drying system comprising of air recirculation pathway and silica gel bed was designed and experimentally tested in this study. To ensure the best moisture adsorption performance, the silica gel was deliberately protected from direct solar radiation and thermal degradation of adsorption performance during operation. The performance of the system was monitored continuously using an Internet of Things (IoT) based monitoring system comprising temperature, relative humidity, airflow, solar irradiance and moisture content sensor. The performance of the drying process was examined in terms of humidity reduction, the distribution of temperature during drying, drying efficiency and the moisture content of the dried product under the solar irradiance range of 400-900 W/m2. The experimental results showed that the shaded silica gel was able to lower the relative humidity of recirculated air up to 9.4%, which resulted in good drying efficiency of 6.28% and 5.76% in the first and second chamber, respectively. The moisture content of noodles in the first and second chambers was, therefore, 0.17 and 0.19, respectively. The results show that keeping the silica gel at a lower operating temperature maintains its moisture absorption ability, increases dehumidification efficiency and performance of the hybrid solar drying system
- 29 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessImpact of Recycled Dehumidified Air via Silica Gel on the performance of a Solar Drying System
Solar drying systems are a promising renewable energy technology that can be used to dry products using solar radiation, and with a lower energy use. One problem, however, is the high humidity of recirculated air that slows water removal and reduces drying efficiency. The use of desiccant materials, especially silica gel, can be an effective solution for desiccant performance and moisture reduction. A hybrid solar drying system comprising of air recirculation pathway and silica gel bed was designed and experimentally tested in this study. To ensure the best moisture adsorption performance, the silica gel was deliberately protected from direct solar radiation and thermal degradation of adsorption performance during operation. The performance of the system was monitored continuously using an Internet of Things (IoT) based monitoring system comprising temperature, relative humidity, airflow, solar irradiance and moisture content sensor. The performance of the drying process was examined in terms of humidity reduction, the distribution of temperature during drying, drying efficiency and the moisture content of the dried product under the solar irradiance range of 400-900 W/m2. The experimental results showed that the shaded silica gel was able to lower the relative humidity of recirculated air up to 9.4%, which resulted in good drying efficiency of 6.28% and 5.76% in the first and second chamber, respectively. The moisture content of noodles in the first and second chambers was, therefore, 0.17 and 0.19, respectively. The results show that keeping the silica gel at a lower operating temperature maintains its moisture absorption ability, increases dehumidification efficiency and performance of the hybrid solar drying system
- 16 February 2026
- Published by Springer Nature
- p. 187-196
Optimization of Penetration Rate for Polycrystalline Diamond Compact Drill Bit Design using Discrete Element Modelling
- 16 February 2026
- Published by Springer Nature
- p. 187-196
Optimization of Penetration Rate for Polycrystalline Diamond Compact Drill Bit Design using Discrete Element Modelling
- Open Access
- 1 December 2025
- Published by Institute of Advanced Engineering and Science in International Journal of Advances in Applied Sciences
- Vol. 14 (4) , 1402-1410
Design and analysis of a portal frame test rig for vertical load testing of goalpost pipeline support
Pipe support is a crucial infrastructure in the oil and gas industry, requiring robust designs to withstand various loads and maintain operational stability. While numerical analysis is commonly used to assess the interaction between pipelines and supports, experimental testing remains essential for validation. However, field testing is often costly and difficult due to safety constraints. To overcome this, a reliable test rig with minimal deflection is needed to ensure accurate experimental results. This study uses finite element analysis (FEA) to evaluate both a goalpost pipeline support and a newly developed portal frame test rig. The test rig was analyzed under two conditions: the failure load of the goalpost support and an amplified load with a factor of 2.5 to simulate unexpected scenarios. Results show the test rig can safely withstand loads up to 40 kN, meeting the EN 1990 safety factor requirement of 1.5. Furthermore, critical components remained within the deflection limit specified by the British Constructional Steelwork Association (BCSA), which is under L/1,000 of the beam length. These results confirm the structural integrity and suitability of the portal frame test rig for accurate testing of the goalpost pipeline support structure.
- 1 December 2025
- Published by Institute of Advanced Engineering and Science in International Journal of Advances in Applied Sciences
- Vol. 14 (4) , 1402-1410
Open AccessDesign and analysis of a portal frame test rig for vertical load testing of goalpost pipeline support
Pipe support is a crucial infrastructure in the oil and gas industry, requiring robust designs to withstand various loads and maintain operational stability. While numerical analysis is commonly used to assess the interaction between pipelines and supports, experimental testing remains essential for validation. However, field testing is often costly and difficult due to safety constraints. To overcome this, a reliable test rig with minimal deflection is needed to ensure accurate experimental results. This study uses finite element analysis (FEA) to evaluate both a goalpost pipeline support and a newly developed portal frame test rig. The test rig was analyzed under two conditions: the failure load of the goalpost support and an amplified load with a factor of 2.5 to simulate unexpected scenarios. Results show the test rig can safely withstand loads up to 40 kN, meeting the EN 1990 safety factor requirement of 1.5. Furthermore, critical components remained within the deflection limit specified by the British Constructional Steelwork Association (BCSA), which is under L/1,000 of the beam length. These results confirm the structural integrity and suitability of the portal frame test rig for accurate testing of the goalpost pipeline support structure.
- Open Access
- 1 September 2025
- Published by Institute of Advanced Engineering and Science in International Journal of Advances in Applied Sciences
- Vol. 14 (3) , 886-893
Test rig development for load test of pipe saddle support
Pipe saddle support is a structure commonly used to support horizontal steel pipe. It prevents direct contact between the pipe and the support. Pipe saddle support can experience displacement due to pipe movement and insufficient stress analysis. Given these concerns, conducting a load test is essential to determine the stress on pipe saddle supports. However, a universal testing machine (UTM) is not suitable for this purpose due to the size limitation. Therefore, this study proposed a test rig setup for the pipe saddle support load test. The test rig consists of a portal frame secured by an underground locking system featuring a strong floor. Additionally, an actual pipe is utilized to replicate actual loading conditions on the pipe saddle support. The applied load is measured using a load cell, with a custom-designed bracket to ensure precise load transfer. Finally, the pipe saddle support specimen is bolted to a base support to maintain stability during the load test. Stress analysis using finite element analysis (FEA) demonstrated that the test rig is suitable for conducting load tests on the specimens with a maximum force of 80 kN. FEA confirmed that the test rig operates within a safety factor of 1.3.
- 1 September 2025
- Published by Institute of Advanced Engineering and Science in International Journal of Advances in Applied Sciences
- Vol. 14 (3) , 886-893
Open AccessTest rig development for load test of pipe saddle support
Pipe saddle support is a structure commonly used to support horizontal steel pipe. It prevents direct contact between the pipe and the support. Pipe saddle support can experience displacement due to pipe movement and insufficient stress analysis. Given these concerns, conducting a load test is essential to determine the stress on pipe saddle supports. However, a universal testing machine (UTM) is not suitable for this purpose due to the size limitation. Therefore, this study proposed a test rig setup for the pipe saddle support load test. The test rig consists of a portal frame secured by an underground locking system featuring a strong floor. Additionally, an actual pipe is utilized to replicate actual loading conditions on the pipe saddle support. The applied load is measured using a load cell, with a custom-designed bracket to ensure precise load transfer. Finally, the pipe saddle support specimen is bolted to a base support to maintain stability during the load test. Stress analysis using finite element analysis (FEA) demonstrated that the test rig is suitable for conducting load tests on the specimens with a maximum force of 80 kN. FEA confirmed that the test rig operates within a safety factor of 1.3.
- Open Access
- 15 August 2025
- Published by Universitas Muhammadiyah Magelang in Automotive Experiences
- Vol. 8 (2) , 281-295
Enhancing Stoichiometric Methane-Air Flames: The Role of N2O Replacement
The oxidizer is used in aviation propellants for its relatively high impulse density and non-toxic nature. At elevated temperatures, nitrous oxide (N₂O) decomposes into approximately 33% oxygen (O₂) and 67% nitrogen (N₂), providing a higher oxygen content than ambient air. This decomposition enables N₂O to produce higher flame temperatures than air. Previous studies have shown that N₂O addition improves flame stability in methane combustion systems. This study examined the substitution of O₂ with N₂O in stoichiometric methane–air premixed flames, using both numerical and experimental methods. One-dimensional and two-dimensional simulations with CHEMKIN PRO revealed that replacing air with N₂O increases flame temperature but reduces laminar flame speed, mainly due to lower local oxygen concentrations in the reaction zone. The simulations also showed that nitrogen oxides (NOₓ) emissions increase significantly in the post-reaction zone, while carbon monoxide (CO) and carbon dioxide (CO₂) emissions decrease. Experimental results confirmed that controlled N₂O addition enhances flame stability, but excessive concentrations can trigger combustion instabilities. Overall, the findings indicate that introducing up to 20% N₂O can increase flame temperature and reduce CO emissions in methane flames.
- 15 August 2025
- Published by Universitas Muhammadiyah Magelang in Automotive Experiences
- Vol. 8 (2) , 281-295
Open AccessEnhancing Stoichiometric Methane-Air Flames: The Role of N2O Replacement
The oxidizer is used in aviation propellants for its relatively high impulse density and non-toxic nature. At elevated temperatures, nitrous oxide (N₂O) decomposes into approximately 33% oxygen (O₂) and 67% nitrogen (N₂), providing a higher oxygen content than ambient air. This decomposition enables N₂O to produce higher flame temperatures than air. Previous studies have shown that N₂O addition improves flame stability in methane combustion systems. This study examined the substitution of O₂ with N₂O in stoichiometric methane–air premixed flames, using both numerical and experimental methods. One-dimensional and two-dimensional simulations with CHEMKIN PRO revealed that replacing air with N₂O increases flame temperature but reduces laminar flame speed, mainly due to lower local oxygen concentrations in the reaction zone. The simulations also showed that nitrogen oxides (NOₓ) emissions increase significantly in the post-reaction zone, while carbon monoxide (CO) and carbon dioxide (CO₂) emissions decrease. Experimental results confirmed that controlled N₂O addition enhances flame stability, but excessive concentrations can trigger combustion instabilities. Overall, the findings indicate that introducing up to 20% N₂O can increase flame temperature and reduce CO emissions in methane flames.
- 30 August 2024
- Published by Elsevier in Ceramics International
- Vol. 50 (22) , 45891-45900
Surface characteristics and machining rate of SS 316L coating developed using hydroxyapatite-mixed EDM process
- 30 August 2024
- Published by Elsevier in Ceramics International
- Vol. 50 (22) , 45891-45900
Surface characteristics and machining rate of SS 316L coating developed using hydroxyapatite-mixed EDM process
- 1 August 2021
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 83 (5) , 119-127
MECHANICAL AND PHYSICAL PROPERTIES OF THERMOPLASTIC CORN STARCH
The awareness to produce biodegradable composite has increased rapidly because of non-toxic and reachable. However, fully biodegradable composite production still low due to the matrix used in the composite is not biodegradable. Thus, this paper presents the study on mechanical and physical properties for the mixtures of corn starch (CS) with different weight percentages of glycerol as thermoplastics corn starch (TPCS) matrix. The selected glycerol contents were at 30, 35 and 40 wt%. The mixtures of CS and different weight percentages of glycerol were made using hot compression moulding at 165°C for 15 minutes to produce the TPCS samples. The mechanical and physical properties were done: the tensile test, hardness test, water absorption test, moisture content test and microstructure analysis under the Scanning Electron Microscopes (SEM). Incorporating 30 wt% loadings of glycerol has increased the tensile strength and hardness. The results show that the addition of higher than 30 wt% loadings of glycerol has decreased the tensile strength and hardness of the TPCS. The physical test results for 30 wt% loadings of glycerol for water absorption test and moisture content show the lowest value than other TPCS samples. However, the density value for all wt% loadings of glycerol does not offer much difference. It reveals that 30 wt% loadings of glycerol in the mixture of CS have shown a good interaction in the TPCS mechanical properties. Based on this finding, the TPCS has huge potential to be used as a matrix to develop a fully biodegradable composite.
- 1 August 2021
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 83 (5) , 119-127
MECHANICAL AND PHYSICAL PROPERTIES OF THERMOPLASTIC CORN STARCH
The awareness to produce biodegradable composite has increased rapidly because of non-toxic and reachable. However, fully biodegradable composite production still low due to the matrix used in the composite is not biodegradable. Thus, this paper presents the study on mechanical and physical properties for the mixtures of corn starch (CS) with different weight percentages of glycerol as thermoplastics corn starch (TPCS) matrix. The selected glycerol contents were at 30, 35 and 40 wt%. The mixtures of CS and different weight percentages of glycerol were made using hot compression moulding at 165°C for 15 minutes to produce the TPCS samples. The mechanical and physical properties were done: the tensile test, hardness test, water absorption test, moisture content test and microstructure analysis under the Scanning Electron Microscopes (SEM). Incorporating 30 wt% loadings of glycerol has increased the tensile strength and hardness. The results show that the addition of higher than 30 wt% loadings of glycerol has decreased the tensile strength and hardness of the TPCS. The physical test results for 30 wt% loadings of glycerol for water absorption test and moisture content show the lowest value than other TPCS samples. However, the density value for all wt% loadings of glycerol does not offer much difference. It reveals that 30 wt% loadings of glycerol in the mixture of CS have shown a good interaction in the TPCS mechanical properties. Based on this finding, the TPCS has huge potential to be used as a matrix to develop a fully biodegradable composite.
- Open Access
- 14 April 2021
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 82 (1) , 105-112
Preliminary Investigation of Using DBD Plasma for Application in Micro Combustors
Dielectric-Barrier-Discharge (DBD) plasma actuators are one of the recent research topics that has caught worldwide attention. Plasma actuators are typically used in the aerospace field of study for their flow control and wide usage of different types of plasma actuators. DBD plasma actuator is an immobile actuator that able to be utilized for its flexibility and light weight parts. Due to the wide usage of DBD plasma, it is also able to be useful in the field of combustion in terms of air flow control. In this research, the DBD plasma actuator is tested on its ability to be applied in micro combustors based on the air flow controlling aspect, the temperature of plasma and effects of vibration of plasma. Experiments were performed in the wind tunnel with smoke generator to show the flow separation by DBD plasma actuator while infrared camera and accelerometer were used to sense the temperature and vibration respectively to investigate the effects of DBD plasma actuator on these aspects. Results shows that the plasma generated has minimal effects of the flow characteristics whereas the temperature of plasma has a maximum of 90?celcius when it is generated continuously. The vibration results indicate that generating plasma produces a small amount of vibration.
- 14 April 2021
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 82 (1) , 105-112
Open AccessPreliminary Investigation of Using DBD Plasma for Application in Micro Combustors
Dielectric-Barrier-Discharge (DBD) plasma actuators are one of the recent research topics that has caught worldwide attention. Plasma actuators are typically used in the aerospace field of study for their flow control and wide usage of different types of plasma actuators. DBD plasma actuator is an immobile actuator that able to be utilized for its flexibility and light weight parts. Due to the wide usage of DBD plasma, it is also able to be useful in the field of combustion in terms of air flow control. In this research, the DBD plasma actuator is tested on its ability to be applied in micro combustors based on the air flow controlling aspect, the temperature of plasma and effects of vibration of plasma. Experiments were performed in the wind tunnel with smoke generator to show the flow separation by DBD plasma actuator while infrared camera and accelerometer were used to sense the temperature and vibration respectively to investigate the effects of DBD plasma actuator on these aspects. Results shows that the plasma generated has minimal effects of the flow characteristics whereas the temperature of plasma has a maximum of 90?celcius when it is generated continuously. The vibration results indicate that generating plasma produces a small amount of vibration.