Ahissan Donatien Ehouman
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ahissan Donatien Ehouman has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- Adjoumani Rodrigue Kouakou
Laboratoire de Thermodynamique et de Physico-Chimie du Milieu (LTPCM), UFR Sciences Fondamentales Appliquées, Université Nangui Abrogoua, 02 BP 801 Abidjan 02, Côte d’Ivoire
4 shared publications Bamba Amara
Laboratoire de Constitution et Réaction de la Matière, UFR SSMT, Université Félix Houphouët-Boigny, Abidjan Cocody, 22 BP 582 Abidjan 22, Côte-d’Ivoire
2 shared publications- Konan Remis Gbangbo
Laboratory of Geographical Sciences, Civil Engineering and Geosciences (LASCIG3) of the JointResearch and Innovation Unit for Engineering Sciences and Techniques (UMRI-STI) of the Institute National Polytechnique Félix HOUPHOUËT-BOIGNY (INP-HB), Yamoussoukro, Côte d'Ivoire
2 shared publications Kouakou Adjoumani Rodrigue
Laboratoire de Thermodynamique et Physico-Chimie du Milieu, UFR SFA, Université Nangui Abrogoua, 02 BP 801 Abidjan 02, Côte-d’Ivoire
2 shared publicationsMariko Kalifa
Laboratoire de Réaction et Constitution de la Matière, Université Félix Houphouët Boigny, 22 BP 582 Abidjan 22, Côte d’Ivoire
2 shared publications- Paulin Marius Niamien
Université Félix Houphouët-Boigny, BP Abidjan-Cocody, Abidjan, Côte D’ivoire
2 shared publications
Latest Publications
- Open Access
- 28 February 2026
- Published by Oriental Scientific Publishing Company in Oriental Journal of Chemistry
- Vol. 1 (42) , 285-290
Microporous Development in Cashew Branch Activated Carbon: Comparative Effects of Sodium and Potassium Hydroxides
Chemical activation of lignocellulosic biomass is a cost‑effective route to tailor microporosity in activated carbons (ACs) for adsorption and gas purification. This study evaluates the comparative effects of sodium hydroxide (NaOH) and potassium hydroxide (KOH) on the development of microporosity in activated carbon derived from cashew (Anacardium occidentale) branch biomass. The precursor was size‑reduced, sieved (pass at 8 mm; retain at 4 mm), impregnated for 24 h in alkaline solutions (typically 500 ppm), oven‑dried (24 h), carbonized in lidded porcelain containers at 500 °C for 3h10 (NaOH) or 3 h 00 (KOH), and subsequently washed to near‑neutral pH and re‑dried. Yield was quantified by mass balance. Microporosity was assessed using the iodine number test (0.1 N I₂, titration with 0.1 N Na₂S₂O₃, starch indicator), a well‑established proxy for the presence of small pores in ACs. Under the stated conditions, average production yields were ~35%. The iodine numbers obtained were ~533 mg·g⁻¹ for NaOH‑activated samples and ~571 mg·g⁻¹ for KOH‑activated samples at 500 °C, indicating a modest advantage of KOH in creating/expanding micropores in this feedstock. Overall, activation agent, impregnation ratio, and thermal schedule critically determine micropore development; KOH shows slightly higher efficacy than NaOH in the present cashew branch system. The results support the viability of cashew branch biomass as a local, sustainable precursor for microporous AC production.
- 28 February 2026
- Published by Oriental Scientific Publishing Company in Oriental Journal of Chemistry
- Vol. 1 (42) , 285-290
Open AccessMicroporous Development in Cashew Branch Activated Carbon: Comparative Effects of Sodium and Potassium Hydroxides
Chemical activation of lignocellulosic biomass is a cost‑effective route to tailor microporosity in activated carbons (ACs) for adsorption and gas purification. This study evaluates the comparative effects of sodium hydroxide (NaOH) and potassium hydroxide (KOH) on the development of microporosity in activated carbon derived from cashew (Anacardium occidentale) branch biomass. The precursor was size‑reduced, sieved (pass at 8 mm; retain at 4 mm), impregnated for 24 h in alkaline solutions (typically 500 ppm), oven‑dried (24 h), carbonized in lidded porcelain containers at 500 °C for 3h10 (NaOH) or 3 h 00 (KOH), and subsequently washed to near‑neutral pH and re‑dried. Yield was quantified by mass balance. Microporosity was assessed using the iodine number test (0.1 N I₂, titration with 0.1 N Na₂S₂O₃, starch indicator), a well‑established proxy for the presence of small pores in ACs. Under the stated conditions, average production yields were ~35%. The iodine numbers obtained were ~533 mg·g⁻¹ for NaOH‑activated samples and ~571 mg·g⁻¹ for KOH‑activated samples at 500 °C, indicating a modest advantage of KOH in creating/expanding micropores in this feedstock. Overall, activation agent, impregnation ratio, and thermal schedule critically determine micropore development; KOH shows slightly higher efficacy than NaOH in the present cashew branch system. The results support the viability of cashew branch biomass as a local, sustainable precursor for microporous AC production.
- Open Access
- 27 June 2024
- Published by Oriental Scientific Publishing Company in Oriental Journal of Chemistry
- Vol. 40 (3) , 666-672
Mitigating Corrosion in Activated Carbon Purified Biogas: A Case Study of Copper and Aluminum Metals
The objective of this study is to investigate the potential reduction in corrosion of aluminum and copper metals when exposed to biogas purified by activated carbon derived from cashew branches. Both aluminum and copper metals were subjected to raw and purified biogas, and their corrosion rates were analyzed using the gravimetric method. The results revealed that the corrosion rate of both metals increased over time when exposed to unfiltered biogas. However, a notable reduction in corrosion rate was observed when the metals were exposed to biogas filtered with activated carbon. This suggests that activated carbon derived from cashew branches could effectively mitigate the corrosive effects of hydrogen sulfide in biogas. Additionally, the study found that aluminum exhibited greater resistance to corrosion compared to copper when exposed to filtered biogas. This research on green inhibitors introduces novel approaches, particularly in utilizing activated carbon from cashew branches for biogas purification, offering a promising strategy to mitigate its corrosive nature. Furthermore, the evaluation of this filtration method's efficacy in protecting aluminum and copper metals underscores its potential significance in corrosion prevention within biogas systems.
- 27 June 2024
- Published by Oriental Scientific Publishing Company in Oriental Journal of Chemistry
- Vol. 40 (3) , 666-672
Open AccessMitigating Corrosion in Activated Carbon Purified Biogas: A Case Study of Copper and Aluminum Metals
The objective of this study is to investigate the potential reduction in corrosion of aluminum and copper metals when exposed to biogas purified by activated carbon derived from cashew branches. Both aluminum and copper metals were subjected to raw and purified biogas, and their corrosion rates were analyzed using the gravimetric method. The results revealed that the corrosion rate of both metals increased over time when exposed to unfiltered biogas. However, a notable reduction in corrosion rate was observed when the metals were exposed to biogas filtered with activated carbon. This suggests that activated carbon derived from cashew branches could effectively mitigate the corrosive effects of hydrogen sulfide in biogas. Additionally, the study found that aluminum exhibited greater resistance to corrosion compared to copper when exposed to filtered biogas. This research on green inhibitors introduces novel approaches, particularly in utilizing activated carbon from cashew branches for biogas purification, offering a promising strategy to mitigate its corrosive nature. Furthermore, the evaluation of this filtration method's efficacy in protecting aluminum and copper metals underscores its potential significance in corrosion prevention within biogas systems.
- Open Access
- 5 September 2023
- Published by Earthline Publishers in Earthline Journal of Chemical Sciences
- Vol. 10 (2) , 267-283
Study of the Thermodynamic Quantities of Adsorption and Activation of Piroxicam in Copper Corrosion in a Nitric Acid Environment
The objective of this work is to assess the inhibitory efficacy of the piroxicam molecule on copper corrosion in a 1M nitric acid medium using the mass loss technique (gravimetry). The inhibition efficiency, represented as IE (%), increases with higher concentrations and temperatures. Various adsorption isotherm models (Langmuir, El-Awady, Freundlich, and Temkin) were employed to describe the interactions between the molecule and metallic copper. The Dubinin-Radushkevich isotherm, along with the Adejo-Ekwenchi isotherm, was utilized to identify the types of adsorption. Additionally, the thermodynamic adsorption and activation functions were determined and analyzed.
- 5 September 2023
- Published by Earthline Publishers in Earthline Journal of Chemical Sciences
- Vol. 10 (2) , 267-283
Open AccessStudy of the Thermodynamic Quantities of Adsorption and Activation of Piroxicam in Copper Corrosion in a Nitric Acid Environment
The objective of this work is to assess the inhibitory efficacy of the piroxicam molecule on copper corrosion in a 1M nitric acid medium using the mass loss technique (gravimetry). The inhibition efficiency, represented as IE (%), increases with higher concentrations and temperatures. Various adsorption isotherm models (Langmuir, El-Awady, Freundlich, and Temkin) were employed to describe the interactions between the molecule and metallic copper. The Dubinin-Radushkevich isotherm, along with the Adejo-Ekwenchi isotherm, was utilized to identify the types of adsorption. Additionally, the thermodynamic adsorption and activation functions were determined and analyzed.
- Open Access
- 3 September 2023
- Published by African Journals Online (AJOL) in Journal of Applied Sciences and Environmental Management
- Vol. 27 (8) , 1627-1632
Evaluation of Metal Contamination of Sediments around an Industrial Gold Mine in Côte d’Ivoire: The Example of Arsenic
The Tongon gold mine produces millions of tons of waste rock and tailings which are stored in dumps around the mine. This mine waste is contaminated with arsenic. Arsenic has acutely toxic effects on aquatic life within polluted areas. The potential for contamination of the area’s aquatic environment is apparent. Therefore the objective of this paper was to evaluate the arsenic contamination of the sediments around the industrial gold mine in Côte d'Ivoire using inductively coupled plasma mass spectroscopy (NexION 2000 ICP-MS, USA) after aqua regia acid digestion. In addition, the metal contamination indices were used to evaluate the degree of arsenic contamination in the sediments. The obtained results indicated that the sediments in the industrial area of the Tongon gold mine have high arsenic concentrations in the proximity of pits and dumps. The geoaccumulation index (-0.09 < Igeo < 2.20) and the pollution load index (0.93) revealed that the sediment is moderately contaminated with arsenic. These findings suggest an ecological risk and therefore the need for environmental monitoring, supported by the elaboration of an effective remedial action strategy to minimize local pollution and contamination.
- 3 September 2023
- Published by African Journals Online (AJOL) in Journal of Applied Sciences and Environmental Management
- Vol. 27 (8) , 1627-1632
Open AccessEvaluation of Metal Contamination of Sediments around an Industrial Gold Mine in Côte d’Ivoire: The Example of Arsenic
The Tongon gold mine produces millions of tons of waste rock and tailings which are stored in dumps around the mine. This mine waste is contaminated with arsenic. Arsenic has acutely toxic effects on aquatic life within polluted areas. The potential for contamination of the area’s aquatic environment is apparent. Therefore the objective of this paper was to evaluate the arsenic contamination of the sediments around the industrial gold mine in Côte d'Ivoire using inductively coupled plasma mass spectroscopy (NexION 2000 ICP-MS, USA) after aqua regia acid digestion. In addition, the metal contamination indices were used to evaluate the degree of arsenic contamination in the sediments. The obtained results indicated that the sediments in the industrial area of the Tongon gold mine have high arsenic concentrations in the proximity of pits and dumps. The geoaccumulation index (-0.09 < Igeo < 2.20) and the pollution load index (0.93) revealed that the sediment is moderately contaminated with arsenic. These findings suggest an ecological risk and therefore the need for environmental monitoring, supported by the elaboration of an effective remedial action strategy to minimize local pollution and contamination.
- 1 November 2022
- Published by Bentham Science Publishers Ltd. in Current Physical Chemistry
Meloxicam Performances For Copper Corrosion Inhibition In 1m Hno3: Experimental And Theoretical Approaches
Background: Copper is a metal that is widely used in many fields such as industry and construction, etc. These different industrial sectors use acid solutions such as nitric acid and hydrochloric acid, etc. The use of acid solutions in the industrial environment causes degradation of materials. In recent decades, the use of corrosion inhibitors has become very essential. Objective: The objective of our study is to test the performance of meloxicam as a copper corrosion inhibitor in a nitric acid medium. Methods: The studies were conducted using the gravimetric method and density functional theory (DFT) at B3LYP/6-311G (d,p) level of theory. The inhibitory efficiency of the molecule increases with increasing concentration of Meloxicam, but decreases with increasing temperature. The adsorption of the molecule on the copper surface follows the Villamil model. Results and Discussion: The thermodynamic quantities of adsorption and activation were determined and discussed. Quantum chemical calculations have allowed determining the molecular descriptors. Conclusion: There is a good agreement between the experimental and theoretical results. Electrochemical studies are envisaged.
- 1 November 2022
- Published by Bentham Science Publishers Ltd. in Current Physical Chemistry
Meloxicam Performances For Copper Corrosion Inhibition In 1m Hno3: Experimental And Theoretical Approaches
Background: Copper is a metal that is widely used in many fields such as industry and construction, etc. These different industrial sectors use acid solutions such as nitric acid and hydrochloric acid, etc. The use of acid solutions in the industrial environment causes degradation of materials. In recent decades, the use of corrosion inhibitors has become very essential. Objective: The objective of our study is to test the performance of meloxicam as a copper corrosion inhibitor in a nitric acid medium. Methods: The studies were conducted using the gravimetric method and density functional theory (DFT) at B3LYP/6-311G (d,p) level of theory. The inhibitory efficiency of the molecule increases with increasing concentration of Meloxicam, but decreases with increasing temperature. The adsorption of the molecule on the copper surface follows the Villamil model. Results and Discussion: The thermodynamic quantities of adsorption and activation were determined and discussed. Quantum chemical calculations have allowed determining the molecular descriptors. Conclusion: There is a good agreement between the experimental and theoretical results. Electrochemical studies are envisaged.
- Open Access
- 6 June 2022
- Published by Elsevier in Scientific African
- Vol. 16
Coupling anaerobic digestion process and electrocoagulation using iron and aluminium electrodes for slaughterhouse wastewater treatment
- 6 June 2022
- Published by Elsevier in Scientific African
- Vol. 16
Open AccessCoupling anaerobic digestion process and electrocoagulation using iron and aluminium electrodes for slaughterhouse wastewater treatment
- 9 October 2021
- Published by Sciencedomain International in International Research Journal of Pure and Applied Chemistry
- p. 1-13
Inhibition Effect of Atenolol on Copper Corrosion in 1M HNO3: Experimental Study and DFT
Atenolol was examined as a copper corrosion inhibitor in 1M nitric acid solution using the mass loss technique and quantum chemical studies, based on density functional theory (DFT) at the B3LYP level with the base 6-311G (d,p). The inhibitory efficiency of the molecule increases with increasing concentration and temperature. The adsorption of the molecule on the copper surface follows the modified Langmuir model. The thermodynamic quantities of adsorption and activation were determined and discussed. The calculated quantum chemical parameters related to the inhibition efficiency are the energy of the highest occupied molecular orbital E(HOMO), the energy of the lowest unoccupied molecular orbital E(LUMO), the HOMO-LUMO energy gap, the hardness (η), softness (S), dipole moment (μ), electron affinity (A), ionization energy (I), absolute electronegativity (χ),absolute electronegativity (χ), fraction (ΔN) of electrons transferred from Atenolol to copper and electrophilicity index(ω). The local reactivity was analyzed through the condensed Fukui function and condensed softness indices to determine the nucleophilic and electrophilic attack sites. There is good agreement between the experimental and theoretical results.
- 9 October 2021
- Published by Sciencedomain International in International Research Journal of Pure and Applied Chemistry
- p. 1-13
Inhibition Effect of Atenolol on Copper Corrosion in 1M HNO3: Experimental Study and DFT
Atenolol was examined as a copper corrosion inhibitor in 1M nitric acid solution using the mass loss technique and quantum chemical studies, based on density functional theory (DFT) at the B3LYP level with the base 6-311G (d,p). The inhibitory efficiency of the molecule increases with increasing concentration and temperature. The adsorption of the molecule on the copper surface follows the modified Langmuir model. The thermodynamic quantities of adsorption and activation were determined and discussed. The calculated quantum chemical parameters related to the inhibition efficiency are the energy of the highest occupied molecular orbital E(HOMO), the energy of the lowest unoccupied molecular orbital E(LUMO), the HOMO-LUMO energy gap, the hardness (η), softness (S), dipole moment (μ), electron affinity (A), ionization energy (I), absolute electronegativity (χ),absolute electronegativity (χ), fraction (ΔN) of electrons transferred from Atenolol to copper and electrophilicity index(ω). The local reactivity was analyzed through the condensed Fukui function and condensed softness indices to determine the nucleophilic and electrophilic attack sites. There is good agreement between the experimental and theoretical results.
- Open Access
- 30 August 2021
- Published by Oriental Scientific Publishing Company in Oriental Journal of Chemistry
- Vol. 37 (4) , 805-812
Study of the Stability and Chemical Reactivity of a Series of Tetrazole Pyrimidine Hybrids by the Density Functional Theory Method (DFT)
Our theoretical study of stability and reactivity was carried out on six (06) molecules of a series of pyrimidine tetrazole hybrids (PTH) substituted with H, F, Cl, Br, OCH3 and CH3 atoms and groups of atoms using the density function theory (DFT). Analysis of the thermodynamic formation quantities confirmed the formation and existence of the series of molecules studied. Quantum chemical calculations at the B3LYP / 6-311G (d, p) level of theory determined molecular descriptors. Global reactivity descriptors were also determined and analyzed. Thus, the results showed that the compound PTH_1 is the most stable, and PTH_5 is the most reactive and nucleophilic. Similarly, the compound PTH_4 is the most electrophilic. The analysis of the local descriptors and the boundary molecular orbitals allowed us to identify the preferred atoms for electrophilic and nucleophilic attacks.
- 30 August 2021
- Published by Oriental Scientific Publishing Company in Oriental Journal of Chemistry
- Vol. 37 (4) , 805-812
Open AccessStudy of the Stability and Chemical Reactivity of a Series of Tetrazole Pyrimidine Hybrids by the Density Functional Theory Method (DFT)
Our theoretical study of stability and reactivity was carried out on six (06) molecules of a series of pyrimidine tetrazole hybrids (PTH) substituted with H, F, Cl, Br, OCH3 and CH3 atoms and groups of atoms using the density function theory (DFT). Analysis of the thermodynamic formation quantities confirmed the formation and existence of the series of molecules studied. Quantum chemical calculations at the B3LYP / 6-311G (d, p) level of theory determined molecular descriptors. Global reactivity descriptors were also determined and analyzed. Thus, the results showed that the compound PTH_1 is the most stable, and PTH_5 is the most reactive and nucleophilic. Similarly, the compound PTH_4 is the most electrophilic. The analysis of the local descriptors and the boundary molecular orbitals allowed us to identify the preferred atoms for electrophilic and nucleophilic attacks.