Aleksandr N. Smirnov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Aleksandr N. Smirnov has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Nikolay V. Ababkov
T.F. Gorbachev Kuzbass State Technical University
11 shared publications - Elena L. Nikonenko
Tomsk State University of Architecture and Building
7 shared publications - Natal'YA A. Popova
Tomsk State University of Architecture and Building, Tomsk, Russia
5 shared publications - Konstantin V. Knyaz’KOv
T.F. Gorbachev Kuzbass State Technical University
4 shared publications Eugeniy Ozhiganov
OOO Kuzbass Welding Center, Kemerovo, 650055 Russia
3 shared publications- Nina A. Koneva
Tomsk State University of Architecture and Building, Tomsk, Russia
3 shared publications
Latest Publications
- Open Access
- 27 August 2026
- Published by T.F. Gorbachev Kuzbass State Technicak University in Vestnik of Kuzbass State Technical University
- No. 3
INFLUENCE OF THE WELDING METHOD OF CORROSION-RESISTANT AUSTENITIC 0.12C-18Cr-10Ni-Ti STEEL ON THE STRUCTURAL STATE
This paper presents the results of a study of welded joints made from 0.12C-18Cr-10Ni-Ti steel blanks in the fusion line zone on both the base metal side and the weld metal side (deposited metal) after manual arc welding (MMA) using standard technology, after semiautomatic argon welding, and after laser welding. Under real-world operating conditions, most welded joints made from corrosion-resistant austenitic steels operate in aggressive environments and under increased loads, which can lead to damage accumulation and elastic-plastic deformation. Furthermore, welded joints of technical devices of hazardous industrial facilities (TDHF) after installation (repair), according to Rostekhnadzor guidelines, must undergo hydraulic testing with elevated pressure or loads exceeding the design load by up to 25% before being put into operation. Corrosion-resistant steels are readily weldable, but specific grades require the development of specialized technologies. The thermal cycle of welding results in complex physical and chemical processes associated with phase transformations and localized structural changes in the metal's heat-affected zone (HAZ). These processes often lead to undesirable effects, such as grain growth, alloying element segregation, intermetallic formation, and, consequently, reduced performance. Based on studies of welded joint samples produced by various methods, it can be concluded that the most advanced joints are produced using both manual arc welding and semiautomatic argon-arc welding with a consumable electrode. Laser welding offers potential for achieving satisfactory performance characteristics in welded joints, but careful selection of the welding mode is necessary.
- 27 August 2026
- Published by T.F. Gorbachev Kuzbass State Technicak University in Vestnik of Kuzbass State Technical University
- No. 3
Open AccessINFLUENCE OF THE WELDING METHOD OF CORROSION-RESISTANT AUSTENITIC 0.12C-18Cr-10Ni-Ti STEEL ON THE STRUCTURAL STATE
This paper presents the results of a study of welded joints made from 0.12C-18Cr-10Ni-Ti steel blanks in the fusion line zone on both the base metal side and the weld metal side (deposited metal) after manual arc welding (MMA) using standard technology, after semiautomatic argon welding, and after laser welding. Under real-world operating conditions, most welded joints made from corrosion-resistant austenitic steels operate in aggressive environments and under increased loads, which can lead to damage accumulation and elastic-plastic deformation. Furthermore, welded joints of technical devices of hazardous industrial facilities (TDHF) after installation (repair), according to Rostekhnadzor guidelines, must undergo hydraulic testing with elevated pressure or loads exceeding the design load by up to 25% before being put into operation. Corrosion-resistant steels are readily weldable, but specific grades require the development of specialized technologies. The thermal cycle of welding results in complex physical and chemical processes associated with phase transformations and localized structural changes in the metal's heat-affected zone (HAZ). These processes often lead to undesirable effects, such as grain growth, alloying element segregation, intermetallic formation, and, consequently, reduced performance. Based on studies of welded joint samples produced by various methods, it can be concluded that the most advanced joints are produced using both manual arc welding and semiautomatic argon-arc welding with a consumable electrode. Laser welding offers potential for achieving satisfactory performance characteristics in welded joints, but careful selection of the welding mode is necessary.
- Open Access
- 26 December 2025
- Published by National Research Tomsk Polytechnic University in Bulletin of the Tomsk Polytechnic University Geo Assets Engineering
- Vol. 336 (12) , 80-90
Combined technologies for extracting hard-to-recover georesources
Relevance. Due to the depletion of easily extractable mineral reserves by open-pit mining, there is an urgent need to develop technologies for extracting hard-to-recover natural resources by underground mining. Aim. Based on the analysis of available practical experience and developed promising technologies, to propose options for developing coal reserves with unfavorable mining and geological conditions with the possibility of their use for the extraction of various georesources. Methods. Content analysis, empirical, physical modeling and prototyping of the future sample of the device, experiments in the form of laboratory tests. Results and conclusions. The prospective volumes of hard-to-recover coal reserves suitable in the future for underground mining, concentrated in steeply inclined seams, are substantiated. The paper reveals the advantages of combined technological solutions, significantly increasing the productivity of the entire technological complex of equipment and allowing to maintain a low level of production costs, despite the increase in the cost of equipment and the volume of preparatory mining operations. The authors have proposed the variants of combined geotechnological solutions based on the creation of new, modernization and expansion of the functions of the existing types of the main technological equipment, as well as various methods of open-pit and underground mining of georesources. In particular, a new means of mechanization developed by the authors is proposed in the form of a multifunctional walking-type support as part of a complex with a heading machine and other necessary means of mechanization of technological operations, designed for high-speed driving of preparatory underground mine workings, for the development of hard-to-recover coal reserves with "short pillars", hydraulically, including in combination with an auger drilling rig. The mechanized complex can also be used for the development of placer deposits of diamonds, gold, titanium, platinum group metals, tin, tungsten, zirconium, tantalum, niobium, rare earth elements and some other georesources.
- 26 December 2025
- Published by National Research Tomsk Polytechnic University in Bulletin of the Tomsk Polytechnic University Geo Assets Engineering
- Vol. 336 (12) , 80-90
Open AccessCombined technologies for extracting hard-to-recover georesources
Relevance. Due to the depletion of easily extractable mineral reserves by open-pit mining, there is an urgent need to develop technologies for extracting hard-to-recover natural resources by underground mining. Aim. Based on the analysis of available practical experience and developed promising technologies, to propose options for developing coal reserves with unfavorable mining and geological conditions with the possibility of their use for the extraction of various georesources. Methods. Content analysis, empirical, physical modeling and prototyping of the future sample of the device, experiments in the form of laboratory tests. Results and conclusions. The prospective volumes of hard-to-recover coal reserves suitable in the future for underground mining, concentrated in steeply inclined seams, are substantiated. The paper reveals the advantages of combined technological solutions, significantly increasing the productivity of the entire technological complex of equipment and allowing to maintain a low level of production costs, despite the increase in the cost of equipment and the volume of preparatory mining operations. The authors have proposed the variants of combined geotechnological solutions based on the creation of new, modernization and expansion of the functions of the existing types of the main technological equipment, as well as various methods of open-pit and underground mining of georesources. In particular, a new means of mechanization developed by the authors is proposed in the form of a multifunctional walking-type support as part of a complex with a heading machine and other necessary means of mechanization of technological operations, designed for high-speed driving of preparatory underground mine workings, for the development of hard-to-recover coal reserves with "short pillars", hydraulically, including in combination with an auger drilling rig. The mechanized complex can also be used for the development of placer deposits of diamonds, gold, titanium, platinum group metals, tin, tungsten, zirconium, tantalum, niobium, rare earth elements and some other georesources.
- 1 November 2025
- Published by Pleiades Publishing Ltd in Technical Physics
- Vol. 70 (11) , 544-551
Influence of Cladding with Flux-Cored Wire on the Structural–Phase State of Steel 20
Using transmission diffraction electron microscopy methods on thin foils, the influence of the metal of surfacing with welding wire of type 0.35С–5Cr–1Mn–1V–1Ni–1W–1Mo–Fe on the structure of the substrate made of steel 20 has been investigated. A quantitative analysis of changes in the fine structure of the substrate and surfacing materials at different distances (0.5 and 3.0 mm) from the fusion line has been performed. The morphological components of the structure, their volume fraction and phase composition have been determined. It has been established that in the initial state, steel 20 is represented by lamellar pearlite and ferrite. Surfacing with welding wire has led to significant destruction of lamellar pearlite, complete fragmentation of ferrite, release of small cementite particles at the boundaries and joints of ferrite fragments, creation of an elastically stressed state of the steel matrix, and strengthening of the substrate by 1.5 times.
- 1 November 2025
- Published by Pleiades Publishing Ltd in Technical Physics
- Vol. 70 (11) , 544-551
Influence of Cladding with Flux-Cored Wire on the Structural–Phase State of Steel 20
Using transmission diffraction electron microscopy methods on thin foils, the influence of the metal of surfacing with welding wire of type 0.35С–5Cr–1Mn–1V–1Ni–1W–1Mo–Fe on the structure of the substrate made of steel 20 has been investigated. A quantitative analysis of changes in the fine structure of the substrate and surfacing materials at different distances (0.5 and 3.0 mm) from the fusion line has been performed. The morphological components of the structure, their volume fraction and phase composition have been determined. It has been established that in the initial state, steel 20 is represented by lamellar pearlite and ferrite. Surfacing with welding wire has led to significant destruction of lamellar pearlite, complete fragmentation of ferrite, release of small cementite particles at the boundaries and joints of ferrite fragments, creation of an elastically stressed state of the steel matrix, and strengthening of the substrate by 1.5 times.
- Open Access
- 30 September 2024
- Published by Altai State Technical University in Фундаментальные проблемы современного материаловедения
- Vol. 21 (3) , 345-356
ВЛИЯНИЕ НАПЛАВКИ ПОРОШКОВОЙ ПРОВОЛОКОЙ НА СТРУКТУРНО-ФАЗОВОЕ СОСТОЯНИЕ СТАЛИ 20
Методами просвечивающей дифракционной электронной микроскопии на тонких фольгах проведены исследования влияния металла наплавки, выполненной сварочной проволокой типа 35Х5ГФНВМ, на структуру подложки из стали 20. Выполнен количественный анализ изменения тонкой структуры материалов подложки и наплавки на различном расстоянии (0,5 и 3,0 мм) от линии сплавления. Определены морфологические составляющие структуры, их объемная доля и фазовый состав. Установлено, что в исходном состоянии сталь 20 представлена пластинчатым перлитом и ферритом. Наплавка сварочной проволокой привела к существенному разрушению пластинчатого перлита, полной фрагментации феррита, выделению мелких частиц цементита на границах и в стыках фрагментов феррита, созданию упруго-напряженного состояния матрицы стали и упрочнению подложки в 1,5 раза.
- 30 September 2024
- Published by Altai State Technical University in Фундаментальные проблемы современного материаловедения
- Vol. 21 (3) , 345-356
Open AccessВЛИЯНИЕ НАПЛАВКИ ПОРОШКОВОЙ ПРОВОЛОКОЙ НА СТРУКТУРНО-ФАЗОВОЕ СОСТОЯНИЕ СТАЛИ 20
Методами просвечивающей дифракционной электронной микроскопии на тонких фольгах проведены исследования влияния металла наплавки, выполненной сварочной проволокой типа 35Х5ГФНВМ, на структуру подложки из стали 20. Выполнен количественный анализ изменения тонкой структуры материалов подложки и наплавки на различном расстоянии (0,5 и 3,0 мм) от линии сплавления. Определены морфологические составляющие структуры, их объемная доля и фазовый состав. Установлено, что в исходном состоянии сталь 20 представлена пластинчатым перлитом и ферритом. Наплавка сварочной проволокой привела к существенному разрушению пластинчатого перлита, полной фрагментации феррита, выделению мелких частиц цементита на границах и в стыках фрагментов феррита, созданию упруго-напряженного состояния матрицы стали и упрочнению подложки в 1,5 раза.
- Open Access
- 29 March 2024
- Published by Altai State Technical University in Фундаментальные проблемы современного материаловедения
- Vol. 21 (1) , 112-121
ИССЛЕДОВАНИЕ ДИСЛОКАЦИОННОЙ СТРУКТУРЫ, ВНУТРЕННИХ НАПРЯЖЕНИЙ И ПЕРЕРАСПРЕДЕЛЕНИЯ АТОМОВ УГЛЕРОДА В ЗОНЕ ЛОКАЛИЗОВАННОЙ ДЕФОРМАЦИИ В КОНСТРУКЦИОННОЙ СТАЛИ 20
В работе представлены результаты исследования дислокационной структуры, величины кривизны-кручения кристаллической решетки, амплитуд полей внутренних напряжений, а также перераспределения атомов углерода в зонах устойчивой локализации деформаций в зависимости от состояния образцов из конструкционной стали 20. Исследовались образцы без эксплуатации, после эксплуатации без разрушения и с разрушением. Образцы растягивали с одинаковой скоростью до появления устойчивой зоны локализации деформации, после чего нагружение останавливали. Для исследования дислокационной структуры в работе использовали метод просвечивающей электронной микроскопии на тонких фольгах. Показано, что деформация образцов из конструкционной стали 20 в направлении «исходный» ® «не разрушенный» ® «разрушенный» во всех морфологических составляющих структуры, а также в целом по материалу постепенно приводит к измельчению структуры вплоть в отдельных участках материала до нанокристаллической. Дислокации перемещаются на границы фрагментов, скалярная плотность дислокаций r уменьшается. Одновременно уменьшаются и внутренние напряжения сдвига sЛ. Изменение локальных напряжений sд носит иной характер, а именно, пластическая составляющая локальных напряжений уменьшается, а упругая резко возрастает. Установлено, что деформация стали 20 приводит к разрушению частиц цементита, расположенных на границах дислокационных фрагментов (объемная доля уменьшается), и образованию карбидов внутри фрагментов (объемная доля их увеличивается). Углерод из разрушенных частиц цементита на границах фрагментов идет на образование частиц цементита внутри фрагментов, на дефекты кристаллической решетки и образование карбидов в новых морфологических структурах (микро- и нанозернах).
- 29 March 2024
- Published by Altai State Technical University in Фундаментальные проблемы современного материаловедения
- Vol. 21 (1) , 112-121
Open AccessИССЛЕДОВАНИЕ ДИСЛОКАЦИОННОЙ СТРУКТУРЫ, ВНУТРЕННИХ НАПРЯЖЕНИЙ И ПЕРЕРАСПРЕДЕЛЕНИЯ АТОМОВ УГЛЕРОДА В ЗОНЕ ЛОКАЛИЗОВАННОЙ ДЕФОРМАЦИИ В КОНСТРУКЦИОННОЙ СТАЛИ 20
В работе представлены результаты исследования дислокационной структуры, величины кривизны-кручения кристаллической решетки, амплитуд полей внутренних напряжений, а также перераспределения атомов углерода в зонах устойчивой локализации деформаций в зависимости от состояния образцов из конструкционной стали 20. Исследовались образцы без эксплуатации, после эксплуатации без разрушения и с разрушением. Образцы растягивали с одинаковой скоростью до появления устойчивой зоны локализации деформации, после чего нагружение останавливали. Для исследования дислокационной структуры в работе использовали метод просвечивающей электронной микроскопии на тонких фольгах. Показано, что деформация образцов из конструкционной стали 20 в направлении «исходный» ® «не разрушенный» ® «разрушенный» во всех морфологических составляющих структуры, а также в целом по материалу постепенно приводит к измельчению структуры вплоть в отдельных участках материала до нанокристаллической. Дислокации перемещаются на границы фрагментов, скалярная плотность дислокаций r уменьшается. Одновременно уменьшаются и внутренние напряжения сдвига sЛ. Изменение локальных напряжений sд носит иной характер, а именно, пластическая составляющая локальных напряжений уменьшается, а упругая резко возрастает. Установлено, что деформация стали 20 приводит к разрушению частиц цементита, расположенных на границах дислокационных фрагментов (объемная доля уменьшается), и образованию карбидов внутри фрагментов (объемная доля их увеличивается). Углерод из разрушенных частиц цементита на границах фрагментов идет на образование частиц цементита внутри фрагментов, на дефекты кристаллической решетки и образование карбидов в новых морфологических структурах (микро- и нанозернах).
- Open Access
- 31 March 2023
- Published by Altai State Technical University in Фундаментальные проблемы современного материаловедения
- Vol. 20 (1) , 83-91
ФОРМИРОВАНИЕ ЗОН УСТОЙЧИВОЙ ЛОКАЛИЗАЦИИ ДЕФОРМАЦИИ В СВАРНЫХ СОЕДИНЕНИЯХ КОНСТРУКЦИОННЫХ СТАЛЕЙ, ХАРАКТЕРИСТИКИ НЕРАЗРУШАЮЩИХ ИСПЫТАНИЙ
В работе выявлены особенности формирования и развития полос Чернова-Людерса (ПЧЛ), а также зон устойчивой локализации деформации в образцах малоуглеродистой стали 20, в том числе и со структурно-фазовой неоднородностью в виде сварных швов, выполненных дуговой сваркой. В последнее время возрос интерес к исследованию формирования и распространения ПЧЛ как начальной стадии деформации. В самом деле, невозможно обойтись без исследований физической природы упругопластического перехода в металлах и сплавах, так как многие инженерные конструкции (особенно со сварными швами), используемые в технике, работают в области упругопластических деформаций и в них накапливаются значительные остаточные деформации. Анализировалась микроструктура и механические свойства материала при одноосном растяжении, были проведены механические испытания с регистрацией картин локализации деформации и металлографические исследования. Исследования проводились на двух партиях плоских образцов с головками из стали 20. Размеры рабочей части образцов 40×4×3 мм. Вторая партия была изготовлена из стали 20 (труба Ø159×18 со сварным швом). Изделие в эксплуатации не было (исходное состояние). Третья партия образцов вырезана из пароотводящей трубы теплоэнергетического оборудования также со сварным швом. Типоразмер трубы Ø159×18, срок наработки 198 тыс. часов (после эксплуатации). Механические испытания проводились на испытательной машине Walter+Bai AG LFM-125 при комнатной температуре. Скорость перемещения подвижного захвата составляла 0,4 мм/мин., что при использованной рабочей длине образцов соответствовало скорости деформирования 1,67×10-4 с-1 (квазистатические испытания). Установлено, что в металле сварных швов деформационные критерии разрушения ниже, чем в основном металле.
- 31 March 2023
- Published by Altai State Technical University in Фундаментальные проблемы современного материаловедения
- Vol. 20 (1) , 83-91
Open AccessФОРМИРОВАНИЕ ЗОН УСТОЙЧИВОЙ ЛОКАЛИЗАЦИИ ДЕФОРМАЦИИ В СВАРНЫХ СОЕДИНЕНИЯХ КОНСТРУКЦИОННЫХ СТАЛЕЙ, ХАРАКТЕРИСТИКИ НЕРАЗРУШАЮЩИХ ИСПЫТАНИЙ
В работе выявлены особенности формирования и развития полос Чернова-Людерса (ПЧЛ), а также зон устойчивой локализации деформации в образцах малоуглеродистой стали 20, в том числе и со структурно-фазовой неоднородностью в виде сварных швов, выполненных дуговой сваркой. В последнее время возрос интерес к исследованию формирования и распространения ПЧЛ как начальной стадии деформации. В самом деле, невозможно обойтись без исследований физической природы упругопластического перехода в металлах и сплавах, так как многие инженерные конструкции (особенно со сварными швами), используемые в технике, работают в области упругопластических деформаций и в них накапливаются значительные остаточные деформации. Анализировалась микроструктура и механические свойства материала при одноосном растяжении, были проведены механические испытания с регистрацией картин локализации деформации и металлографические исследования. Исследования проводились на двух партиях плоских образцов с головками из стали 20. Размеры рабочей части образцов 40×4×3 мм. Вторая партия была изготовлена из стали 20 (труба Ø159×18 со сварным швом). Изделие в эксплуатации не было (исходное состояние). Третья партия образцов вырезана из пароотводящей трубы теплоэнергетического оборудования также со сварным швом. Типоразмер трубы Ø159×18, срок наработки 198 тыс. часов (после эксплуатации). Механические испытания проводились на испытательной машине Walter+Bai AG LFM-125 при комнатной температуре. Скорость перемещения подвижного захвата составляла 0,4 мм/мин., что при использованной рабочей длине образцов соответствовало скорости деформирования 1,67×10-4 с-1 (квазистатические испытания). Установлено, что в металле сварных швов деформационные критерии разрушения ниже, чем в основном металле.
- 1 January 2022
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2509 (1) , 020001
Structural-phase state and internal stress fields of samples from 0.12С-1Сr-1Mo-1V steel near zones of deformations localization
A study of metal samples of sections of steam pipelines made of 0.12C-1Cr-1Mo-1V steel after long-term operation (260 thousand hours) and deformation before the formation of zones of stable localization of deformations by the method of electron microscopy was carried out in this work. Various sections of samples made of 0.12C-1Cr-1Mo-1V steel were investigated, namely, directly in the zones of localization of deformation and at a distance of 3 mm from these zones. The phase composition was determined (qualitatively and quantitatively), as a result of the studies carried out for each sample and the following parameters of the fine structure were calculated: volume fractions of structural components of steel, scalar ρ and excess ρ± dislocation density, curvature-torsion of the crystal lattice χ, amplitude of internal stresses (shear stress and long-range stresses). All quantitative parameters of the fine structure were determined both in each structural component of the steel, and in general for each investigated section of the sample. It was found that not the entire volume of the metal of the sample after a short-term test before reaching a stable localization of deformation has the same microstructure.
- 1 January 2022
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2509 (1) , 020001
Structural-phase state and internal stress fields of samples from 0.12С-1Сr-1Mo-1V steel near zones of deformations localization
A study of metal samples of sections of steam pipelines made of 0.12C-1Cr-1Mo-1V steel after long-term operation (260 thousand hours) and deformation before the formation of zones of stable localization of deformations by the method of electron microscopy was carried out in this work. Various sections of samples made of 0.12C-1Cr-1Mo-1V steel were investigated, namely, directly in the zones of localization of deformation and at a distance of 3 mm from these zones. The phase composition was determined (qualitatively and quantitatively), as a result of the studies carried out for each sample and the following parameters of the fine structure were calculated: volume fractions of structural components of steel, scalar ρ and excess ρ± dislocation density, curvature-torsion of the crystal lattice χ, amplitude of internal stresses (shear stress and long-range stresses). All quantitative parameters of the fine structure were determined both in each structural component of the steel, and in general for each investigated section of the sample. It was found that not the entire volume of the metal of the sample after a short-term test before reaching a stable localization of deformation has the same microstructure.
- Open Access
- 2 September 2021
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 64 (8) , 572-580
Influence of deformation degree of austenitic steels welded joints on structural state and internal stresses felds in weld line zone
Nowadays initial assessment of welding quality is performed by testing equipment with increased loads (high pressure) at technical devices of hazardous production facilities. Test requirements are regulated by standardized documents of the Federal Service for Environmental, Technological and Nuclear Oversight of Russia (Rostekhnadzor). Recently, along with traditional tests, a “stress test” was used – the essence of which is to load pipeline section to the yield point, followed by leak test. However, in scientifc publications there is practically no information about physical processes occurring in the base metal and in welded joints during such tests. In addition, effect of preload (deformation) on the parameters of substructure and internal stresses feld in welded joints of austenitic steels and, consequently, on the further troublefree operation of the tested equipment was not evaluated. The paper analyzes changes in structural state and values of internal stresses in the samples of austenitic steel under the action of high loads. It substantiates the use of modulated current welding with automatic control of heat input process in molten weld pool. The admissible limits values of plastic deformation are argued when testing technical devices with high pressure for this type of steel. In order to reduce the risk of damage to austenitic steels welded joints of technical devices of hazardous industrial facilities, performed by pulsed welding with smalldrop transfer, and to exclude formation of microdefects in them, high pressure tests (stress test) can be performed under loads that create deformations in metal, not exceeding 5 %. For joints welded by manual arc welding, deformations should be less than 5 %. Welded joints made by pulsed welding with largedrop transfer (with and without defects) are not recommended to be tested with high pressure.
- 2 September 2021
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 64 (8) , 572-580
Open AccessInfluence of deformation degree of austenitic steels welded joints on structural state and internal stresses felds in weld line zone
Nowadays initial assessment of welding quality is performed by testing equipment with increased loads (high pressure) at technical devices of hazardous production facilities. Test requirements are regulated by standardized documents of the Federal Service for Environmental, Technological and Nuclear Oversight of Russia (Rostekhnadzor). Recently, along with traditional tests, a “stress test” was used – the essence of which is to load pipeline section to the yield point, followed by leak test. However, in scientifc publications there is practically no information about physical processes occurring in the base metal and in welded joints during such tests. In addition, effect of preload (deformation) on the parameters of substructure and internal stresses feld in welded joints of austenitic steels and, consequently, on the further troublefree operation of the tested equipment was not evaluated. The paper analyzes changes in structural state and values of internal stresses in the samples of austenitic steel under the action of high loads. It substantiates the use of modulated current welding with automatic control of heat input process in molten weld pool. The admissible limits values of plastic deformation are argued when testing technical devices with high pressure for this type of steel. In order to reduce the risk of damage to austenitic steels welded joints of technical devices of hazardous industrial facilities, performed by pulsed welding with smalldrop transfer, and to exclude formation of microdefects in them, high pressure tests (stress test) can be performed under loads that create deformations in metal, not exceeding 5 %. For joints welded by manual arc welding, deformations should be less than 5 %. Welded joints made by pulsed welding with largedrop transfer (with and without defects) are not recommended to be tested with high pressure.
- 1 January 2017
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1801, 030003
The structure and phase composition of welded joint after deformation
The paper addresses the issue of the structure and phase composition of welded joint and focuses on their investigation after plastic deformation. The contribution of internal stresses to the formation of phase composition and fine structure of welded joint is shown herein. Electrode welding is used to obtain welded joint in St3 steel. Specimens are subjected to a quasi-static tensile deformation ranging from 0 to 5% under 370 MPa loading. TEM investigations on thin foil specimens allow studying the structure and phase composition within the heat-affected zone at 1 mm distance from base material and 0.5 mm from welding material. The degree of plastic deformation is shown for both base and welding materials and includes their morphology, phase composition, defect structure and its parameters. Long-range stresses are divided into plastic and elastic. Plastic deformation has no qualitative effect on the material structure, however, it modifies its quantitative parameters. With the increase of deformation degree, the perlite component becomes more imperfect and transforms, first, to a fractured perlite and then to ferrite, thereby decreasing the volume ratio of perlite. Polarization of the dislocation structure is observed. The amplitude of internal stress fields grows. Unlike the shear stresses, long-range stresses manifest their intensive growth. The elastic component makes the major contribution to the long-range stresses resulting in the formation of microcracks.
- 1 January 2017
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1801, 030003
The structure and phase composition of welded joint after deformation
The paper addresses the issue of the structure and phase composition of welded joint and focuses on their investigation after plastic deformation. The contribution of internal stresses to the formation of phase composition and fine structure of welded joint is shown herein. Electrode welding is used to obtain welded joint in St3 steel. Specimens are subjected to a quasi-static tensile deformation ranging from 0 to 5% under 370 MPa loading. TEM investigations on thin foil specimens allow studying the structure and phase composition within the heat-affected zone at 1 mm distance from base material and 0.5 mm from welding material. The degree of plastic deformation is shown for both base and welding materials and includes their morphology, phase composition, defect structure and its parameters. Long-range stresses are divided into plastic and elastic. Plastic deformation has no qualitative effect on the material structure, however, it modifies its quantitative parameters. With the increase of deformation degree, the perlite component becomes more imperfect and transforms, first, to a fractured perlite and then to ferrite, thereby decreasing the volume ratio of perlite. Polarization of the dislocation structure is observed. The amplitude of internal stress fields grows. Unlike the shear stresses, long-range stresses manifest their intensive growth. The elastic component makes the major contribution to the long-range stresses resulting in the formation of microcracks.
- 1 January 2017
- Published by AIP Publishing in AIP Conference Proceedings
Structure and phase composition of welded joints modified by different welding techniques
The paper presents the results of transmission electron microscopy (TEM) during the study of structure and phase composition of heat-affected zone (HAZ) of welded joints modified via four welding techniques, namely: electrode welding and electropercussive welding both with and without artificial flaws. The artificial flows represent aluminum pieces. TEM studies are carried out within the heat-affected zone, i.e. between the deposited and base metal, at 0.5 mm distance to the former. The 0.09C-2Mn-1Si-Fe steel type is used for welding. It is shown how the type of welding affects steel morphology, phase composition, defect structure and its parameters. The type of carbide phase is detected as well as the shape and location of particles. Volume fractions are estimated for the structural steel components, alongside with such parameters as the size of α-phase fragments, scalar and excess dislocation densities, and bending-torsion amplitude of the crystal lattice. Based on these results, we determine the welding technique and the structural component thus launching a mechanism of microcrack nucleation.
- 1 January 2017
- Published by AIP Publishing in AIP Conference Proceedings
Structure and phase composition of welded joints modified by different welding techniques
The paper presents the results of transmission electron microscopy (TEM) during the study of structure and phase composition of heat-affected zone (HAZ) of welded joints modified via four welding techniques, namely: electrode welding and electropercussive welding both with and without artificial flaws. The artificial flows represent aluminum pieces. TEM studies are carried out within the heat-affected zone, i.e. between the deposited and base metal, at 0.5 mm distance to the former. The 0.09C-2Mn-1Si-Fe steel type is used for welding. It is shown how the type of welding affects steel morphology, phase composition, defect structure and its parameters. The type of carbide phase is detected as well as the shape and location of particles. Volume fractions are estimated for the structural steel components, alongside with such parameters as the size of α-phase fragments, scalar and excess dislocation densities, and bending-torsion amplitude of the crystal lattice. Based on these results, we determine the welding technique and the structural component thus launching a mechanism of microcrack nucleation.