Hyunmin Jeong
Hyunmin Jeong has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Sangkil Kim
Pusan National University
6 shared publications - Gyoungdeuk Kim
Korea Aerospace Research Institute (KARI), Daejeon, South Korea
3 shared publications - Nohgyeom Ha
Department of Electronics Engineering, Pusan National University, Busan, Republic of Korea
3 shared publications - Apostolos Georgiadis
2582 CN The Hague, The Netherlands
2 shared publications - Manos M. Tentzeris
Georgia Institute of Technology
2 shared publications - Myeongha Hwang
Department of Electronics Engineering, Pusan National University, Busan, South Korea
2 shared publications
Latest Publications
- 20 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Internet of Things Journal
- Vol. 11 (12) , 21857-21871
Polarization Diversity and Transfer Learning-Based Modulation Optimization for High-Speed Dual Channel MIMO Backscatter Communication
This article presents a novel approach to address the challenges in backscatter communication (BackCom) for the Internet of Things. The traditional use of I/Q load modulator based on parametric transistor models often suffers from performance degradation due to discrepancies with actual transistor models caused by thermal and environmental noise sources. To overcome this issue, this article proposes an active circuit modeling technique based on artificial neural network (ANN)-based transfer learning, which utilizes actual measurement data to model the I/Q load modulator accurately. Furthermore, an optimization algorithm is applied to achieve an optimal high-order modulation scheme, leading to improved energy efficiency by 40%. By leveraging machine learning-based modeled I/Q modulators, the proposed approach enables high-speed wireless data communication in a dual-channel configuration. This article also conducts theoretical analysis to define the required performance of a dual-polarized Vivaldi antenna for implementing polarization diversity in BackCom. This analysis provides guidelines for achieving optimal performance in terms of spectral efficiency and error vector magnitude (EVM). The experimental results demonstrate that the proposed approach achieves a spectral efficiency of 2.0 bps/Hz based on 4-QAM modulation within a 150-MHz bandwidth. The measured EVM is 9.35%, indicating the effectiveness of the proposed technique in achieving reliable and efficient wireless data communication in backscatter systems. This article presents a comprehensive approach combining accurate circuit modeling, optimization algorithms, and theoretical analysis to enable high-speed, ultralow-power wireless data communication in BackCom systems.
- 20 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Internet of Things Journal
- Vol. 11 (12) , 21857-21871
Polarization Diversity and Transfer Learning-Based Modulation Optimization for High-Speed Dual Channel MIMO Backscatter Communication
This article presents a novel approach to address the challenges in backscatter communication (BackCom) for the Internet of Things. The traditional use of I/Q load modulator based on parametric transistor models often suffers from performance degradation due to discrepancies with actual transistor models caused by thermal and environmental noise sources. To overcome this issue, this article proposes an active circuit modeling technique based on artificial neural network (ANN)-based transfer learning, which utilizes actual measurement data to model the I/Q load modulator accurately. Furthermore, an optimization algorithm is applied to achieve an optimal high-order modulation scheme, leading to improved energy efficiency by 40%. By leveraging machine learning-based modeled I/Q modulators, the proposed approach enables high-speed wireless data communication in a dual-channel configuration. This article also conducts theoretical analysis to define the required performance of a dual-polarized Vivaldi antenna for implementing polarization diversity in BackCom. This analysis provides guidelines for achieving optimal performance in terms of spectral efficiency and error vector magnitude (EVM). The experimental results demonstrate that the proposed approach achieves a spectral efficiency of 2.0 bps/Hz based on 4-QAM modulation within a 150-MHz bandwidth. The measured EVM is 9.35%, indicating the effectiveness of the proposed technique in achieving reliable and efficient wireless data communication in backscatter systems. This article presents a comprehensive approach combining accurate circuit modeling, optimization algorithms, and theoretical analysis to enable high-speed, ultralow-power wireless data communication in BackCom systems.
- Open Access
- 30 August 2022
- Published by MDPI AG in Electronics
- Vol. 11 (17) , 2729
Design of a Flat-Panel Metasurface Reflectarray C-Band Antenna
This paper presents the design of a flat-panel metasurface reflectarray antenna fed by a circular horn antenna for satellite applications. A metasurface-based reflectarray antenna is similar to a flat-panel reflector and is characterized by a reflection angle adjustment that is free from the well-known Snell’s law. This was done by compensating the angle of the incident wave using the structure of each unit cell. A unit cell of the designed metasurface is composed of a dual-ring resonator. Many satellites use a reflectarray antenna due to its flat-panel structure and the capability of steering the reflection angle of the incident wave. This paper presents the detailed design procedure using a commercial 3D EM simulator and the operation principle of the flat-panel metasurface reflectarray antenna, including the simulation setup, design environment and automation. The proposed design method is scalable to any EM solvers for numerical analysis. A reflectarray composed of a 16 × 16-unit cell array at 5.8 GHz (C-band) was designed and validated by measurement as a proof of concept. It is excited by a low-cost linearly polarized circular horn cantenna. The measured antenna gain and radiation patterns show good agreement with the simulation. The measured antenna gain of the reflectarray was 22.4 dBi (cross-pol suppression level: 36 dB), and the reflection angle was 15° at normal incidence.
- 30 August 2022
- Published by MDPI AG in Electronics
- Vol. 11 (17) , 2729
Open AccessDesign of a Flat-Panel Metasurface Reflectarray C-Band Antenna
This paper presents the design of a flat-panel metasurface reflectarray antenna fed by a circular horn antenna for satellite applications. A metasurface-based reflectarray antenna is similar to a flat-panel reflector and is characterized by a reflection angle adjustment that is free from the well-known Snell’s law. This was done by compensating the angle of the incident wave using the structure of each unit cell. A unit cell of the designed metasurface is composed of a dual-ring resonator. Many satellites use a reflectarray antenna due to its flat-panel structure and the capability of steering the reflection angle of the incident wave. This paper presents the detailed design procedure using a commercial 3D EM simulator and the operation principle of the flat-panel metasurface reflectarray antenna, including the simulation setup, design environment and automation. The proposed design method is scalable to any EM solvers for numerical analysis. A reflectarray composed of a 16 × 16-unit cell array at 5.8 GHz (C-band) was designed and validated by measurement as a proof of concept. It is excited by a low-cost linearly polarized circular horn cantenna. The measured antenna gain and radiation patterns show good agreement with the simulation. The measured antenna gain of the reflectarray was 22.4 dBi (cross-pol suppression level: 36 dB), and the reflection angle was 15° at normal incidence.
- Open Access
- 11 November 2021
- Published by MDPI AG in Electronics
- Vol. 10 (22) , 2758
Educational Low-Cost C-Band FMCW Radar System Comprising Commercial Off-the-Shelf Components for Indoor Through-Wall Object Detection
This paper presents an educational low-cost C-band frequency-modulated continuous wave (FMCW) radar system for use in indoor through-wall metal detection. Indoor remote-sensing applications, such as through-wall detection and positioning, are essential for the comprehensive realization of the internet of things or super-connected societies. The proposed system comprises a two-stage radio-frequency power amplifier, a voltage-controlled oscillator, circuits for frequency modulation and system synchronization, a mixer, a 3-dB power divider, a low-noise amplifier, and two cylindrical horn antennas (Tx/Rx antennas). The antenna yields gain values in the 6.8~7.8 range when operating in the 5.83~5.94 GHz frequency band. The backscattered Tx signal is sampled at 4.5 kHz using the Arduino UNO analog-to-digital converter. Thereafter, the sampled signal is transferred to the MATLAB platform and analyzed using a customized FMCW radar algorithm. The proposed system is built using commercial off-the-shelf components, and it can detect targets within a 56.3 m radius in indoor environments. In this study, the system could successfully detect targets through a 4 cm-thick ply board with a measurement accuracy of less than 10 cm.
- 11 November 2021
- Published by MDPI AG in Electronics
- Vol. 10 (22) , 2758
Open AccessEducational Low-Cost C-Band FMCW Radar System Comprising Commercial Off-the-Shelf Components for Indoor Through-Wall Object Detection
This paper presents an educational low-cost C-band frequency-modulated continuous wave (FMCW) radar system for use in indoor through-wall metal detection. Indoor remote-sensing applications, such as through-wall detection and positioning, are essential for the comprehensive realization of the internet of things or super-connected societies. The proposed system comprises a two-stage radio-frequency power amplifier, a voltage-controlled oscillator, circuits for frequency modulation and system synchronization, a mixer, a 3-dB power divider, a low-noise amplifier, and two cylindrical horn antennas (Tx/Rx antennas). The antenna yields gain values in the 6.8~7.8 range when operating in the 5.83~5.94 GHz frequency band. The backscattered Tx signal is sampled at 4.5 kHz using the Arduino UNO analog-to-digital converter. Thereafter, the sampled signal is transferred to the MATLAB platform and analyzed using a customized FMCW radar algorithm. The proposed system is built using commercial off-the-shelf components, and it can detect targets within a 56.3 m radius in indoor environments. In this study, the system could successfully detect targets through a 4 cm-thick ply board with a measurement accuracy of less than 10 cm.
- Open Access
- 30 September 2021
- Published by Korean Institute of Electromagnetic Engineering and Science in The Journal of Korean Institute of Electromagnetic Engineering and Science
- Vol. 32 (9) , 836-844
Design of an Arduino-Based FMCW Radar using Cantennas
한국전자파학회논문지 (The Journal of Korean Institute of Electromagnetic Engineering and Science)
- 30 September 2021
- Published by Korean Institute of Electromagnetic Engineering and Science in The Journal of Korean Institute of Electromagnetic Engineering and Science
- Vol. 32 (9) , 836-844
Open AccessDesign of an Arduino-Based FMCW Radar using Cantennas
한국전자파학회논문지 (The Journal of Korean Institute of Electromagnetic Engineering and Science)
- Open Access
- 31 August 2021
- Published by Korean Institute of Electromagnetic Engineering and Science in The Journal of Korean Institute of Electromagnetic Engineering and Science
- Vol. 32 (8) , 690-698
Design of a 3D T-Shaped Dipole Antenna Inspired by Origami and Kirigami Theory
한국전자파학회논문지 (The Journal of Korean Institute of Electromagnetic Engineering and Science)
- 31 August 2021
- Published by Korean Institute of Electromagnetic Engineering and Science in The Journal of Korean Institute of Electromagnetic Engineering and Science
- Vol. 32 (8) , 690-698
Open AccessDesign of a 3D T-Shaped Dipole Antenna Inspired by Origami and Kirigami Theory
한국전자파학회논문지 (The Journal of Korean Institute of Electromagnetic Engineering and Science)