Yuheng Zeng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yuheng Zeng has a total of 234 co-authors. Here are the top co-authors by number of shared publications:
- Jichun Ye
Zhejiang Provincial Engineering Research Center of Energy Optoelectronic Materials and Devices Ningbo Institute of Materials Technology and Engineering Chinese Academy of Sciences Ningbo China
26 shared publications Wei Liu
24 shared publicationsZunke Liu
23 shared publicationsMingdun Liao
Ningbo Institute of Materials Technology and Engineering Chinese Academy of Sciences (CAS) Ningbo P. R. China
17 shared publicationsHaojiang Du
Ningbo Institute of Materials Technology and Engineering
16 shared publicationsJichun Ye
16 shared publications
Latest Publications
- Open Access
- 22 October 2026
- Published by Wiley in Advanced Functional Materials
- p. e79108
Molecular Bridging Enables Uniform and Solvent‐Resilient Buried Contacts for Efficient and Stable Perovskite/TOPCon Tandem Solar Cells
Self‐assembled monolayers (SAMs) enable high‐performance inverted perovskite solar cells and perovskite/silicon tandem solar cells, but polar solvents can partially disrupt preformed SAMs and produce nonuniform buried contacts, a challenge amplified on silicon substrates. Here, 3‐(9H‐carbazol‐9‐yl)propan‐1‐aminium iodide (CzPA) is introduced as a molecular bridge at the SAM/perovskite buried interface. The carbazole unit promotes π–π interactions with the SAM, improving monolayer retention during solvent exposure, while the terminal ammonium group interacts with iodide‐containing precursor species to regulate interfacial nucleation. Furthermore, the iodide ions can effectively passivate the iodide vacancies at the buried interface. The reconstructed interface accelerates early‐stage nucleation, promotes orientationally ordered crystal growth, and reduces residual tensile stress, thereby yielding a more p‐type heterojunction and effectively suppressing non‐radiative recombination. CzPA‐modified wide‐bandgap inverted single‐junction cells deliver a PCE of 23.79%. Applied to perovskite/tunnel oxide passivating contact (TOPCon) tandems, this strategy improves perovskite continuity in pyramid valleys, enabling 1 cm 2 devices with a PCE of 33.4%. Unencapsulated tandems retain 88% of their initial PCE after 800 h of one‐sun maximum‐power‐point tracking and 90% of their post‐burn‐in PCE after 737 h at 85°C, underscoring the robustness of the reconstructed buried interface.
- 22 October 2026
- Published by Wiley in Advanced Functional Materials
- p. e79108
Open AccessMolecular Bridging Enables Uniform and Solvent‐Resilient Buried Contacts for Efficient and Stable Perovskite/TOPCon Tandem Solar Cells
Self‐assembled monolayers (SAMs) enable high‐performance inverted perovskite solar cells and perovskite/silicon tandem solar cells, but polar solvents can partially disrupt preformed SAMs and produce nonuniform buried contacts, a challenge amplified on silicon substrates. Here, 3‐(9H‐carbazol‐9‐yl)propan‐1‐aminium iodide (CzPA) is introduced as a molecular bridge at the SAM/perovskite buried interface. The carbazole unit promotes π–π interactions with the SAM, improving monolayer retention during solvent exposure, while the terminal ammonium group interacts with iodide‐containing precursor species to regulate interfacial nucleation. Furthermore, the iodide ions can effectively passivate the iodide vacancies at the buried interface. The reconstructed interface accelerates early‐stage nucleation, promotes orientationally ordered crystal growth, and reduces residual tensile stress, thereby yielding a more p‐type heterojunction and effectively suppressing non‐radiative recombination. CzPA‐modified wide‐bandgap inverted single‐junction cells deliver a PCE of 23.79%. Applied to perovskite/tunnel oxide passivating contact (TOPCon) tandems, this strategy improves perovskite continuity in pyramid valleys, enabling 1 cm 2 devices with a PCE of 33.4%. Unencapsulated tandems retain 88% of their initial PCE after 800 h of one‐sun maximum‐power‐point tracking and 90% of their post‐burn‐in PCE after 737 h at 85°C, underscoring the robustness of the reconstructed buried interface.
- 14 October 2026
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 310
Prospects and theoretical investigation of edge isolation technology in multi-cut TOPCon solar cells
- 14 October 2026
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 310
Prospects and theoretical investigation of edge isolation technology in multi-cut TOPCon solar cells
- Open Access
- 7 July 2026
- Published by Wiley in Advanced Materials
- Vol. 38 (45) , e73918
Nitrogen‐Incorporated Silicon Dioxide Interlayer Enables Pinhole‐Reduced and Robust TOPCon With a High Implied Open‐Circuit Voltage over 760 mV
Tunnel oxide passivating contact (TOPCon) technology has emerged as an industrial cornerstone for high‐efficiency crystalline silicon (c‐Si) solar cells. However, its passivation performance remains constrained by the thermal fragility of the ultrathin silicon dioxide (SiO x ) interface and the resulting formation of pinholes. Here, we report a nitrogen (N)‐incorporated TOPCon structure in which nitrogen (N) atoms are in situ doped into amorphous silicon via plasma‐enhanced chemical vapor deposition (PECVD) and are driven to the SiO x during annealing to form a robust SiO x N y interlayer. First‐principles calculations reveal that SiO x N y exhibits significantly enhanced bonding strength and superior thermal stability. Finite element simulations further show that SiO x N y possesses a thermal expansion coefficient better matched to both c‐Si and poly‐Si, suppressing stress concentration, preventing interface fracture, and reducing pinhole density. This atomic‐scale modification enables record‐breaking passivation performance, achieving an implied open‐circuit voltage of 760 mV and a low single‐sided recombination current density of 0.35 fA/cm 2 . Device simulations predict that the efficiencies of various TOPCon‐based cells can be significantly enhanced with minimal additional cost. Experimental data demonstrate that front‐junction TOPCon cells can achieve an efficiency improvement of 0.2%. This simple and industry‐compatible interface‐engineering strategy provides a highly scalable pathway for boosting TOPCon and back‐contact TOPCon solar cells’ performances.
- 7 July 2026
- Published by Wiley in Advanced Materials
- Vol. 38 (45) , e73918
Open AccessNitrogen‐Incorporated Silicon Dioxide Interlayer Enables Pinhole‐Reduced and Robust TOPCon With a High Implied Open‐Circuit Voltage over 760 mV
Tunnel oxide passivating contact (TOPCon) technology has emerged as an industrial cornerstone for high‐efficiency crystalline silicon (c‐Si) solar cells. However, its passivation performance remains constrained by the thermal fragility of the ultrathin silicon dioxide (SiO x ) interface and the resulting formation of pinholes. Here, we report a nitrogen (N)‐incorporated TOPCon structure in which nitrogen (N) atoms are in situ doped into amorphous silicon via plasma‐enhanced chemical vapor deposition (PECVD) and are driven to the SiO x during annealing to form a robust SiO x N y interlayer. First‐principles calculations reveal that SiO x N y exhibits significantly enhanced bonding strength and superior thermal stability. Finite element simulations further show that SiO x N y possesses a thermal expansion coefficient better matched to both c‐Si and poly‐Si, suppressing stress concentration, preventing interface fracture, and reducing pinhole density. This atomic‐scale modification enables record‐breaking passivation performance, achieving an implied open‐circuit voltage of 760 mV and a low single‐sided recombination current density of 0.35 fA/cm 2 . Device simulations predict that the efficiencies of various TOPCon‐based cells can be significantly enhanced with minimal additional cost. Experimental data demonstrate that front‐junction TOPCon cells can achieve an efficiency improvement of 0.2%. This simple and industry‐compatible interface‐engineering strategy provides a highly scalable pathway for boosting TOPCon and back‐contact TOPCon solar cells’ performances.
- 25 May 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 18 (22) , 31530-31541
Nitrous Oxide-Plasma Silicon Oxide Coupled with Carbon-Incorporated Polycrystalline Silicon Enables Highly Passivated TOPCon Solar Cells
Tunnel oxide passivated contact (TOPCon) solar cells have become the industrial mainstream for high-efficiency crystalline silicon photovoltaics. Further efficiency gains critically depend on achieving ultrahigh passivation performance while maintaining full industrial compatibility. However, achieving highly passivated TOPCon through the synergy of chemical and electric field-effect passivation remains challenging, because simultaneously obtaining high-quality interfacial SiOx and poly-Si films along with a suitable phosphorus-diffusion profile in the silicon substrate is difficult. In this study, we develop a highly passivated TOPCon structure featuring an ultrathin silicon oxide (SiOx) layer prepared via N2O plasma oxidation combined with a carbon-incorporated polycrystalline silicon (poly-Si) layer, resulting in a synergistic improvement in both chemical and field-effect passivation. Notably, a uniform, continuous, and amorphous ultrathin SiOx film provides high chemical passivation, whereas the introduction of carbon into poly-Si suppresses poly-Si crystallization, increases hydrogen accumulation at the SiOx/silicon interface, reduces the poly-Si work function, and forms favorable energy band bending, collectively contributing to superior passivation performance. As a result, the optimized TOPCon structure not only exhibits high tolerance to annealing temperature and carbon content but also achieves excellent passivation, with an implied open-circuit voltage (iVoc) of 760 mV, an ultralow recombination current density (J0,s) of 0.5 fA/cm2, and a minority carrier lifetime (τeff) of 27.9 ms. Industrial validation shows an absolute efficiency gain of 0.05% in mass-produced large-area TOPCon cells, confirming the scalability and effectiveness of this TOPCon structure.
- 25 May 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 18 (22) , 31530-31541
Nitrous Oxide-Plasma Silicon Oxide Coupled with Carbon-Incorporated Polycrystalline Silicon Enables Highly Passivated TOPCon Solar Cells
Tunnel oxide passivated contact (TOPCon) solar cells have become the industrial mainstream for high-efficiency crystalline silicon photovoltaics. Further efficiency gains critically depend on achieving ultrahigh passivation performance while maintaining full industrial compatibility. However, achieving highly passivated TOPCon through the synergy of chemical and electric field-effect passivation remains challenging, because simultaneously obtaining high-quality interfacial SiOx and poly-Si films along with a suitable phosphorus-diffusion profile in the silicon substrate is difficult. In this study, we develop a highly passivated TOPCon structure featuring an ultrathin silicon oxide (SiOx) layer prepared via N2O plasma oxidation combined with a carbon-incorporated polycrystalline silicon (poly-Si) layer, resulting in a synergistic improvement in both chemical and field-effect passivation. Notably, a uniform, continuous, and amorphous ultrathin SiOx film provides high chemical passivation, whereas the introduction of carbon into poly-Si suppresses poly-Si crystallization, increases hydrogen accumulation at the SiOx/silicon interface, reduces the poly-Si work function, and forms favorable energy band bending, collectively contributing to superior passivation performance. As a result, the optimized TOPCon structure not only exhibits high tolerance to annealing temperature and carbon content but also achieves excellent passivation, with an implied open-circuit voltage (iVoc) of 760 mV, an ultralow recombination current density (J0,s) of 0.5 fA/cm2, and a minority carrier lifetime (τeff) of 27.9 ms. Industrial validation shows an absolute efficiency gain of 0.05% in mass-produced large-area TOPCon cells, confirming the scalability and effectiveness of this TOPCon structure.
- Open Access
- 6 May 2026
- Published by Springer Nature in Nature Communications
- Vol. 17 (1)
Carbon-incorporated polysilicon interconnection layer enables robust self-assembled monolayer anchoring for perovskite/TOPCon tandem solar cells
Due to the deficiency of anchoring sites (i.e., hydroxyl groups), self-assembled monolayers (SAMs) pose a significant challenge for achieving dense and uniform coverage on textured substrates, thereby hindering the development of perovskite/silicon tandem solar cells. Here, we develop an in-situ carbon incorporation strategy for polysilicon-based tunnel recombination interconnection layers to enhance SAM adsorption and anchoring. Carbon-incorporated polysilicon exhibits a higher surface hydroxyl group density and enhanced hydrophilicity, facilitating SAM adsorption and forming robust SAM anchoring. This leads to improved uniformity and continuity of SAM coverage, along with enhanced perovskite crystallization, resulting in pinhole‑free and denser perovskite deposition on textured substrates. Moreover, the strategy further adjusts the energy level alignment of the SAM surface, facilitating hole extraction. After integration into perovskite/tunnel oxide passivating contact (TOPCon) tandems (~1 cm2), we achieve a record efficiency of 33.84% (certified at 33.50%), with excellent operation stability, retaining 80% of its initial efficiency after 800 h.
- 6 May 2026
- Published by Springer Nature in Nature Communications
- Vol. 17 (1)
Open AccessCarbon-incorporated polysilicon interconnection layer enables robust self-assembled monolayer anchoring for perovskite/TOPCon tandem solar cells
Due to the deficiency of anchoring sites (i.e., hydroxyl groups), self-assembled monolayers (SAMs) pose a significant challenge for achieving dense and uniform coverage on textured substrates, thereby hindering the development of perovskite/silicon tandem solar cells. Here, we develop an in-situ carbon incorporation strategy for polysilicon-based tunnel recombination interconnection layers to enhance SAM adsorption and anchoring. Carbon-incorporated polysilicon exhibits a higher surface hydroxyl group density and enhanced hydrophilicity, facilitating SAM adsorption and forming robust SAM anchoring. This leads to improved uniformity and continuity of SAM coverage, along with enhanced perovskite crystallization, resulting in pinhole‑free and denser perovskite deposition on textured substrates. Moreover, the strategy further adjusts the energy level alignment of the SAM surface, facilitating hole extraction. After integration into perovskite/tunnel oxide passivating contact (TOPCon) tandems (~1 cm2), we achieve a record efficiency of 33.84% (certified at 33.50%), with excellent operation stability, retaining 80% of its initial efficiency after 800 h.
Enhanced Passivation of Boron‐Doped Polysilicon Passivated Contacts With a Single‐Sided J 0 of 2.8 fA/cm 2 by Dual‐Layer Silicon Oxide Structure
Boron (B)‐induced interface defects remain a key bottleneck that limits the passivation quality of p‐type tunnel oxide passivating contacts (TOPCon), thereby constraining the efficiency of back‐contact TOPCon (TBC) solar cells. Here, we introduce a dual‐layer silicon oxide (SiO x ) design that forms a SiO x /p + poly‐Si/SiO x /p ++ poly‐Si passivation structure. The additional SiO x layer effectively mitigates interlayer stress, preventing blistering during high‐temperature annealing, and increases interfacial hydrogen concentration to suppress defect states. Through systematic optimization of the preparation and annealing conditions of the outer SiO x layer, the p‐type TOPCon structures achieve outstanding passivation on n‐type wafers, with a single‐sided recombination current density ( J 0,s ) of 2.8 fA/cm 2 and an implied open‐circuit voltage ( iV oc ) of 741 mV. This represents one of the best results reported to date, surpassing the current industrial records. Compared with the previous single‐layer SiO x designs, this configuration delivers a substantial improvement of passivation while simultaneously enabling a reduced poly‐Si thickness. Numerical simulations further demonstrate a 0.18% absolute efficiency gain in TBC cells with the dual‐layer structure compared to single‐layer configuration. This work demonstrates that a dual‐layer SiO x architecture effectively lowers interface defect density and enhances p‐type TOPCon passivation, underscoring its significant potential for industrial application in high‐efficiency TBC cells.
Enhanced Passivation of Boron‐Doped Polysilicon Passivated Contacts With a Single‐Sided J 0 of 2.8 fA/cm 2 by Dual‐Layer Silicon Oxide Structure
Boron (B)‐induced interface defects remain a key bottleneck that limits the passivation quality of p‐type tunnel oxide passivating contacts (TOPCon), thereby constraining the efficiency of back‐contact TOPCon (TBC) solar cells. Here, we introduce a dual‐layer silicon oxide (SiO x ) design that forms a SiO x /p + poly‐Si/SiO x /p ++ poly‐Si passivation structure. The additional SiO x layer effectively mitigates interlayer stress, preventing blistering during high‐temperature annealing, and increases interfacial hydrogen concentration to suppress defect states. Through systematic optimization of the preparation and annealing conditions of the outer SiO x layer, the p‐type TOPCon structures achieve outstanding passivation on n‐type wafers, with a single‐sided recombination current density ( J 0,s ) of 2.8 fA/cm 2 and an implied open‐circuit voltage ( iV oc ) of 741 mV. This represents one of the best results reported to date, surpassing the current industrial records. Compared with the previous single‐layer SiO x designs, this configuration delivers a substantial improvement of passivation while simultaneously enabling a reduced poly‐Si thickness. Numerical simulations further demonstrate a 0.18% absolute efficiency gain in TBC cells with the dual‐layer structure compared to single‐layer configuration. This work demonstrates that a dual‐layer SiO x architecture effectively lowers interface defect density and enhances p‐type TOPCon passivation, underscoring its significant potential for industrial application in high‐efficiency TBC cells.
- Open Access
- 20 April 2026
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (46) , e75401
Enabling 748.6 mV Open‐Circuit Voltage in Industrial Bifacial Tunnel Oxide Passivating Contact Solar Cells With Multi‐Layer Polysilicon and Tailored Silver Paste
Although tunnel oxide passivating contact (TOPCon) solar cells have become a leading photovoltaic technology, the traditional single‐layer polysilicon (poly‐Si) structure remains a critical challenge in balancing parasitic absorption, passivation performance, and firing‐through degradation. To address this issue, we propose an ultrathin three‐layer poly‐Si stack (60 nm) separated by ultrathin SiO x interlayers, combined with a tailored rear silver paste. Notably, the outer poly‐Si layer with higher phosphorus doping facilitates electrical contact during firing‐through, while the inner poly‐Si layer with lower phosphorus doping exhibits higher crystallinity, facilitating passivation quality; meanwhile, the intermediate‐buffer poly‐Si ensures strong robustness. Moreover, a specific silver paste formulation with low corrosivity and excellent rheological properties enables the formation of low‐contact resistance. The resulting TOPCon devices achieve a certified efficiency of 26.07% and an exceptional open‐circuit voltage of 748.6 mV, representing a milestone approaching that of silicon heterojunction cells. Moreover, this design effectively reduces parasitic absorption, yielding a high bifaciality of 88.6%.
- 20 April 2026
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (46) , e75401
Open AccessEnabling 748.6 mV Open‐Circuit Voltage in Industrial Bifacial Tunnel Oxide Passivating Contact Solar Cells With Multi‐Layer Polysilicon and Tailored Silver Paste
Although tunnel oxide passivating contact (TOPCon) solar cells have become a leading photovoltaic technology, the traditional single‐layer polysilicon (poly‐Si) structure remains a critical challenge in balancing parasitic absorption, passivation performance, and firing‐through degradation. To address this issue, we propose an ultrathin three‐layer poly‐Si stack (60 nm) separated by ultrathin SiO x interlayers, combined with a tailored rear silver paste. Notably, the outer poly‐Si layer with higher phosphorus doping facilitates electrical contact during firing‐through, while the inner poly‐Si layer with lower phosphorus doping exhibits higher crystallinity, facilitating passivation quality; meanwhile, the intermediate‐buffer poly‐Si ensures strong robustness. Moreover, a specific silver paste formulation with low corrosivity and excellent rheological properties enables the formation of low‐contact resistance. The resulting TOPCon devices achieve a certified efficiency of 26.07% and an exceptional open‐circuit voltage of 748.6 mV, representing a milestone approaching that of silicon heterojunction cells. Moreover, this design effectively reduces parasitic absorption, yielding a high bifaciality of 88.6%.
- 24 March 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 18 (13) , 19208-19216
Addressing the Optical–Electrical Trade-Off via Rear Polished TOPCon Structures for Efficient Perovskite/Silicon Tandem Solar Cells
Perovskite/silicon tandem solar cells (TSCs) based on tunnel oxide passivating contact (TOPCon) bottom cells are among the most promising pathways toward commercialization, yet their performance is constrained by inadequate passivation in the p-type region of the bottom cell. In this work, we replace the conventional textured rear surface with an alkaline-polished surface, producing a p-type TOPCon structure with substantially enhanced passivation, which yields a high open-circuit voltage of 727 mV in the bottom cell (implied open-circuit voltage (iVoc) of the TOPCon precursor is 737 mV). This electrical gain, combined with optical compensation provided by a rear SiNx/Ag reflector, enables the resulting perovskite/TOPCon tandem solar cell to achieve an outstanding open-circuit voltage of 1.964 V and a notable power conversion efficiency of 32.14%.
- 24 March 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 18 (13) , 19208-19216
Addressing the Optical–Electrical Trade-Off via Rear Polished TOPCon Structures for Efficient Perovskite/Silicon Tandem Solar Cells
Perovskite/silicon tandem solar cells (TSCs) based on tunnel oxide passivating contact (TOPCon) bottom cells are among the most promising pathways toward commercialization, yet their performance is constrained by inadequate passivation in the p-type region of the bottom cell. In this work, we replace the conventional textured rear surface with an alkaline-polished surface, producing a p-type TOPCon structure with substantially enhanced passivation, which yields a high open-circuit voltage of 727 mV in the bottom cell (implied open-circuit voltage (iVoc) of the TOPCon precursor is 737 mV). This electrical gain, combined with optical compensation provided by a rear SiNx/Ag reflector, enables the resulting perovskite/TOPCon tandem solar cell to achieve an outstanding open-circuit voltage of 1.964 V and a notable power conversion efficiency of 32.14%.