Somu C.
Research Subjects
Somu C. has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Ranjith Rajamanickam
SNS College of Technology
2 shared publications - P. K. Giridharan
Kumaraguru College of Technology
1 shared publication - Ramu Murugan
Department of Mechanical Engineering, Amrita School of Engineering, Amrita Vishwa Vidyapeetham, Coimbatore, India
1 shared publication
Latest Publications
- 1 May 2022
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 11 (5) , 053010
Electric Discharge Machining of Inconel 718 Under a Distinct Dielectric Medium
In this research, an attempt was made to machine the Inconel 718 alloy under varied dielectric medium with the objective of generating wealth from waste and establishing a green environment. Experiments were conducted to analyze the influence of input variables under the EDM oil, pure sunflower oil, used sunflower oil, palm oil and ground nut oil insulating medium. Five different tools namely copper, brass, aluminium, copper—graphite and aluminium—graphite was utilized for investigation and experimental runs were designed using Taguchi mixed orthogonal array. The results revealed that the characteristics of the dielectric fluid influences the spark generation and machined cycle time. The findings divulged that dielectric fluid with a high density facilitates flushing, low specific heating distributes heat uniformly and low carbon content eliminates black spots. Electrode with low thermal conductivity dissipates more heat and low latent heat of fusion erodes excessively. Micro pits, globules, angled and clouded blobs, black spots, material dunes and redeposited material are the various features observed on the machined surface texture.
- 1 May 2022
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 11 (5) , 053010
Electric Discharge Machining of Inconel 718 Under a Distinct Dielectric Medium
In this research, an attempt was made to machine the Inconel 718 alloy under varied dielectric medium with the objective of generating wealth from waste and establishing a green environment. Experiments were conducted to analyze the influence of input variables under the EDM oil, pure sunflower oil, used sunflower oil, palm oil and ground nut oil insulating medium. Five different tools namely copper, brass, aluminium, copper—graphite and aluminium—graphite was utilized for investigation and experimental runs were designed using Taguchi mixed orthogonal array. The results revealed that the characteristics of the dielectric fluid influences the spark generation and machined cycle time. The findings divulged that dielectric fluid with a high density facilitates flushing, low specific heating distributes heat uniformly and low carbon content eliminates black spots. Electrode with low thermal conductivity dissipates more heat and low latent heat of fusion erodes excessively. Micro pits, globules, angled and clouded blobs, black spots, material dunes and redeposited material are the various features observed on the machined surface texture.
- 27 August 2021
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 9 (3) , 035025
A novel Cu-Gr composite electrode development for electric discharge machining of Inconel 718 alloy
Requirement of processes with high productivity leads to the development of new tools and machining technique. One such attempt was made to develop a Copper Composite (CC) tool reinforced with graphite particles through the stir casting route. The CC tool was utilized to machine the Inconel 718 alloy using Electric Discharge Machining (EDM) technique by varying input variables viz tool material, discharge current, pulse on time, pulse off time and gap distance. Brass, Copper, Copper—5% Graphite (CG5), Copper—10% Graphite (CG10), Copper—15% Graphite (CG15) are the various used tool material whereas Material Removal Rate (MRR), Tool Wear Ratio (TWR) and Surface Roughness (R a ) were recorded as responses. The results revealed that using the CG10 and CG15 tools causes arcing and open circuit under some parametric conditions. CG5 offers best MRR and least TWR owing to the bridging effect, high thermal conductivity and lesser density which was suitable for roughing operation whereas brass offers least R a which was recommended for finishing operation. The surface topography was analyzed with the aid of Scanning Electron Microscope (SEM). Micro crack, pock marks, globules and remelted layers are some of the defects observed in surface morphology. The process parameters was optimized using VIKOR technique.
- 27 August 2021
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 9 (3) , 035025
A novel Cu-Gr composite electrode development for electric discharge machining of Inconel 718 alloy
Requirement of processes with high productivity leads to the development of new tools and machining technique. One such attempt was made to develop a Copper Composite (CC) tool reinforced with graphite particles through the stir casting route. The CC tool was utilized to machine the Inconel 718 alloy using Electric Discharge Machining (EDM) technique by varying input variables viz tool material, discharge current, pulse on time, pulse off time and gap distance. Brass, Copper, Copper—5% Graphite (CG5), Copper—10% Graphite (CG10), Copper—15% Graphite (CG15) are the various used tool material whereas Material Removal Rate (MRR), Tool Wear Ratio (TWR) and Surface Roughness (R a ) were recorded as responses. The results revealed that using the CG10 and CG15 tools causes arcing and open circuit under some parametric conditions. CG5 offers best MRR and least TWR owing to the bridging effect, high thermal conductivity and lesser density which was suitable for roughing operation whereas brass offers least R a which was recommended for finishing operation. The surface topography was analyzed with the aid of Scanning Electron Microscope (SEM). Micro crack, pock marks, globules and remelted layers are some of the defects observed in surface morphology. The process parameters was optimized using VIKOR technique.