OAOlusegun Olufemi Ajide

Olusegun Olufemi Ajide

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Olusegun Olufemi Ajide has a total of 36 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Corrosion behaviour of hot-rolled A356/DPSA composites synthesised by gravity die casting in 0.5 M NaOH

    by Thomas Aghogho Orhadahwe, Olusegun Olufemi Ajide, Nosa Idusuyi

    This study investigates the corrosion behaviour of hot-rolled A356 aluminium composites reinforced with Date Palm Seed Ash (DPSA), produced by gravity die casting, in 0.5 M NaOH solution using electrochemical techniques. The results showed that DPSA addition improved corrosion resistance compared to the unreinforced alloy, with optimal performance observed at 0.5–0.75 wt.% reinforcement. The 0.5 wt.% composite exhibited the highest polarisation resistance (2100 .cm2) and the largest capacitive response, while Tafel polarisation showed that 0.75 wt.% had the lowest corrosion current density (1.519 ×10-3 A/cm2), indicating optimum resistance in NaOH. SEM/EDX analysis confirmed improved surface integrity and reduced porosity for the optimised composite. The hot-rolled composites are suitable for structural applications in the process industry.

  • Artificial Intelligence Driven Optimisation of Scaffold Design and Production in Tissue Engineering: A Critical Review

    by A.D. Ozieme, A.A. Adeleye, O.O. Ajide

    The synergy of Artificial Intelligence (AI) technology and Tissue Engineering (TE) is creating a new frontier in regenerative medicine. Conventional design of scaffolds for enhancing cell attachment, growth and differentiation is well reported to be achieved through experimental methods. The AI is an emerging technique offering a powerful computational approach that can be deployed to analyse nonlinear and other complex interactions between different scaffold parameters. The foregoing makes it possible to predict and improve designs more efficiently. In this work, attempt is made to critically review the use of AI from traditional machine learning models to advanced deep learning systems for improving scaffold structure, composition and biological performance. Critical attention is made to the roles of supervised and unsupervised learning in predictive modelling, the use of generative algorithms for structural design and the application of evolutionary methods for optimising multiple design objectives. The synergy between AI, computational biomechanics, finite element modelling and Additive Manufacturing (AM) is examined, showing how innovations such as digital twin technology and automatic bioprinting have emerged. The review also explores how AI is deployed for material selection, surface property prediction and biodegradability evaluation in composite materials. Current challenges such as limited data, difficulty in model interpretation and ethical considerations are well discussed along with future directions that include physics-informed networks and combined AI systems. This review highlights progress in AI-driven scaffold optimization, emphasizing improved accuracy, consistency, and personalization in regenerative medicine.


  • Open Access

    Investigation of Mechanical, Corrosion and Microstructural Behaviour of Heat Treated Cr-Modified Al-Mg-Si Alloy

    by Olusegun Olufemi Ajide, Temilade Ruth Adelakun, Itopa Godwin Akande, Temilola Taiwo Olugasa, Nikhil Kumar

    Despite the choice of Al-Mg-Si alloy as a material for innumerable industrial and structural applications, challenges such as undesired scratch resistance, formability and mechanical properties deterioration in saline environment hinders the extent of its application for automotive and aerospace components. Nevertheless, with the growing interest in the application of Al-Mg-Si alloy in automotive and aerospace industries, there is need for cautious control of thermal treatments and inclusion of alloying elements with requisite potentials for enhancing the microstructure and mechanical properties of the alloy. Chromium is known to improve strength and corrosion resistance in several applications. Therefore, this study focuses on the investigation of the effect of Cr particles inclusion in Al-Mg-Si alloy. The effect of ageing heat treatment on selected properties of Al-Mg-Si-Cr alloy was also studied in this work. The Al-Mg-Si and Al-Mg-Si-Cr alloys were developed using a two-step stir casting technique. Chromium was added to Al-Mg-Si alloy at varying percentages of 0, 0.5, 1.0, 1.5, 2.0 and 2.5. All the samples were solution treated in an electric furnace at 500 oC for 30 minutes and water quenched. Then the samples were artificially aged at 210 oC for 3 hours and quenched in natural air. The hardness test revealed that the inclusion of Cr particles in Al-Mg-Si alloy samples increased hardness from 35.03 Kgf/mm2 (hardness of Al-Mg-Si-0%Cr alloy sample) to a maximum value of 126.54 Kgf/mm2 (hardness of Al-Mg-Si-1.5%Cr alloy sample). After heat treatment, the hardness of Al-Mg-Si-0%Cr alloy sample increased to 80.84 Kgf/mm2, while that of Al-Mg-Si-1.5%Cr alloy sample decreased slightly to 120.88 Kgf/mm2. The impact strength test also showed that the inclusion of Cr in Al-Mg-Si alloy increased impact strength from 9.52 J/mm2 (impact strength of Al-Mg-Si-0%Cr alloy sample) to a maximum value of 19.04 J/mm2 (impact strength of Al-Mg-Si-2.0%Cr alloy sample). After heat treatment, the impact strength of Al-Mg-Si-0%Cr alloy sample increased marginally to 10.09 J/mm2, while that of Al-Mg-Si-2.0%Cr alloy sample decreased slightly to 17.57 J/mm2. The tensile and electrochemical tests revealed that the heat-treated Al-Mg-Si-1.0%Cr alloy sample exhibited the highest tensile strength and lowest corrosion rate of 152 MPa and 0.0014 mm/year, respectively. The microstructural examination further revealed that the inclusion of Cr particles in Al-Mg-Si alloy improved its surface morphology. Al-Mg-Si-1.0%Cr alloy sample was adjudged to possess the best microstructural properties. Therefore, this sample is recommended as a potential material for machine tools and other structural or advanced manufacturing applications.

  • Open Access

    Optimization of the Factors Influencing Biodegradation and Thermal Stability of Banana Pseudo Stem Fibers in Nigeria

    by Abideen Temitayo Oyewo, Oluleke Olugbemiga Oluwole, Olusegun Olufemi Ajide, Temidayo Emmanuel Omoniyi, Hyunjin Kim, Yong Jun Choi, Young-Kwon Park, Murid Hussain

    Lignocellulosic fibers, one of natural biopolymers, are derived from abundant banana pseudo stem (BPS) agricultural waste in different parts of Nigeria. In this study, the lignocellulosic fibers of three common banana cultivars, agbagba, paranta, and omini, were investigated to determine their chemical composition and mechanical properties. Furthermore, the experimental investigations were correlated with the corresponding Taguchi L9 orthogonal array design under three factors – fiber treatment, diameter, and cultivar type – to find the optimal factors that are pertinent to the desired biodegradation and thermal stability of the fibers. The optimization results indicated that the fiber treatment followed by diameter and the cultivar type was the most influential of the responses, respectively. However, increased cellulosic content led to higher tensile strength and modulus, while higher lignin corresponded to higher elasticity. Meanwhile, the predictions of the biodegradation and thermal stability derived from the Taguchi design via S/N ratio ANOVA and regression modeling correlated adequately with the corresponding experimental observations. Ultimately, the fibers with optimum factors were T3D1C1 and T3D1C3, where T3, D1, C1, and C3 denote that the associated fiber was treated with acetic acid, had a diameter of 60.77 µm, and belong to the cultivar type of agbagba and omini, respectively.


  • Examining the mechanical response and microstructural evolution of heat-treated Al-5Si-3Cu alloy for automotive applications

    by O.O. Ajide, O.C. Adedokun, N. Idusuyi, Nikil Kumar, O.A. Aogo, O.J. Ajao, A.S. Adebayo, K.K. Sexena, Ankita Joshi, Chander Prakash

    Aluminium-Silicon (Al-Si) based alloys are gaining more prominence among researchers for automotive applications. In this paper, the impact of copper alloying element and artificial ageing treatment on the mechanical response and microstructural evolution of Al-Si based alloys synthesised from aluminium scrap are examined, as there is need to gear up the urge for the usage of metallic scraps for production of alloys for automotive applications. The as-cast Al-Si alloy and its form with copper as alloying element (1.5% and 3% Cu) were produced using liquid metallurgy route. Solution heat treatment was carried out at 500℃ and artificial ageing was carried out at 190℃ for 0.5, 1, 1.5, 2 and 2.5 h. Mechanical properties and microstructural characterisations of the as-cast and artificially aged forms of Al-Si based alloys were performed. The hardness tests were performed according to ASTM A29/A29M–15. Impact strength was determined according to ASTM D256. Tensile tests were performed based on ASTM E8. Microstructures of the synthesised Al-Si alloys were examined using optical microscopy and scanning electron microscopy techniques. In as-cast condition of the Al-5Si-Cu alloy, impact strength increases with increase in copper content. Al5Si-Cu alloy with 3% copper content and artificially aged at 190°C for 2.5 h exhibited the highest impact strength. Hardness number increases with the increase in copper content up to 1.5% and the ageing time. Additional increase in the ageing time yielded decrease in the hardness number. Results revealed that artificial ageing enhances mechanical and microstructural characteristics of the Al-Si alloys. Ageing treated Al-Si alloys exhibited peak hardness, impact strength and ultimate tensile strength (UTS) values of 77.47 kgf/mm2, 17 J/mm2 and 137.80 MPa, respectively. The obtained results are indicative of mechanical properties enhancement when compared with as-cast Al-Si alloys with maximum hardness, impact strength and UTS of 43.71 kgf/mm2, 12.92 J/mm2 and 123.18 MPa, respectively. Significant improvement in mechanical properties was achieved in Al-Si-Cu alloy with copper content and artificial ageing when compared to that without copper inclusion. This may be attributed to the evolution of equiaxed precipitates and the fact that copper-rich Al-Si-Cu alloys promotes formation of precipitation strengthening phases of α-AlFeMnSi. This study shows that the mechanical properties of Al-5Si-Cu alloys produced using aluminium scrap-based materials were enhanced using artificial ageing treatment and the benefit can be utilised for automotive applications.


  • Open Access

    Physico-chemical, Thermal and Micro-structural Characterization of Four Common Banana Pseudo-Stem Fiber Cultivars in Nigeria

    by Abideen Temitayo Oyewo, Oluleke Olugbemiga Oluwole, Olusegun Olufemi Ajide, Temidayo Emmanuel Omoniyi, Parveen Akhter, Muhammad Haris Hamayun, Bo Sung Kang, Young-Kwon Park, Murid Hussain

    This study explores Banana pseudo-stem fiber (BPSF) derived from BPF cultivars that are common in Nigeria. The four cultivars are known locally as Agbagba, Omini, Panbola, and Paranta. This study characterized these cultivars to gain insight into their physical, thermal and microstructural properties. The BPSFs were obtained after manual BPS retting and treated with a 2 wt. % sodium hydroxide solution to improve the fiber quality. Data from the characterization revealed the agbagba cultivar to give the highest percentage recovery (3%) and thermal stability at elevated temperatures with a residual char of 14%. The percentage of cellulose, lignin, hemicellulose, and ash content were determined by chemical composition analysis. FTIR spectroscopy showed a lower lignin and hemicellulose absorption band in the agbagba cultivar while scanning electron microscopy supported the FTIR results. Agabagba’s crystallinity index (XRD) of 61.7% was higher than other cultivars, and X-ray fluorescence (XRF) and a biodegradation test also showed that only agbagba cultivar contained calcium and had the strongest resilience to microbial attack under simulated soil conditions. Agbagba BPSF may be a viable reinforcement in bio-fiber polymer composites needing high strength due to its balanced qualities that have been demonstrated in comparison to other cultivars.


  • Influence of Ti/TiC interface and its site of formation on the properties of powder metallurgically fabricated Ti-based composites reinforced with carbonaceous materials: A review

    by Mary A. Awotunde, Adewale O. Adegbenjo, Olusegun O. Ajide, Peter A. Olubambi

    The applications of carbon allotrope-reinforced Ti-based composites have witnessed enormous expansion in recent times owing to their light weight and competitive properties. However, a consistent controversy still exists on the process of in-situ TiC formation (during powder preparation, reinforcement dispersion and synthesis), its site within the composite and particularly the role it plays on the properties of the bulk composite. Although some authors have opined that the presence of TiC in the bulk composite enhances its overall properties, others hold a contrary opinion. Hence, this current study is aimed at reviewing the positions of the previous studies on this seemingly controversial subject up to date; with a view to broadening the available knowledge base on this crucial area of interest.


  • Open Access

    Thermal characterization of straight and curve edge blade liquid fuel swirl burner

    by Olanrewaju Miracle Oyewola, Patrick Mark Singh, Ademola Samuel Akinwonmi, Olusegun Olufemi Ajide, Tajudeen Abiola Ogunniyi Salau

    Accurate monitoring and controlling of the temperature in the combustion chamber can raise the burner efficiency, combustion intensity, fuel consumption and reduce pollutant emission. However, except combustion is accurately monitored and controlled, high concentration of pollutant gases and products like carbon monoxide (CO) and soot can form in the combustion chamber. This paper compares the combustion thermal profiles in a liquid fuel swirl burner using developed straight edge and curve edge blade swirlers at (20, 30, 40, 50 and 60)° for 6, 8, 10 and 12 number of blades in order to optimize the temperature of the burner. Measurements were made in straight and curve blades liquid fuel swirl burner in order to study and compare the thermal characteristics of the straight and curve edge blades in optimizing the combustion dynamics. Similarly, measurements were made for burner without swirl generator and the combustion temperature assessed. Thermal profile was measured in the direction of flow via the six axial ports at distance ((d) =150, 350, 550, 750, 950 and 1150 mm) from the burner exit using Chromium-Zinc thermocouple. Results showed that the wavelength and oscillation of temperature decay in the same type of blade followed the same trend and the peak of combustion intensity is nearer the nozzle for curve edge blades than the straight edge blade. Six (6) blades performed best with the highest temperature in all the ports, while 12 blades gave the least performance. Findings further show that curve edge blade swirlers gave better performance than straight edge blade swirlers with highest temperature of (1065 and 1015) °C, respectively. Hence, it is recommended especially where high temperature and stability application is desirable


  • Open Access

    Examination of Reynolds number effect on the development of round jet flow

    by Olanrewaju Miracle Oyewola, Adebunmi Okediji, Olusegun Olufemi Ajide, Muyiwa Samuel Adaramola

    In this study, the Reynolds number effect on the development of round jet flow is presented. The jet is produced from a smoothly contracting round nozzle and the flow structure is controlled by varying the air blower speed in order to obtain various Reynolds numbers (Re). The flow Reynolds number considered varies between 1140 and 9117. Mean velocity measurements were taken using hot-wire probe at different axial and lateral distances (0≤x/d≤50, where x is the downstream distance and d is the nozzle diameter) for the jet flow and at for 0≤x/d≤30 in long pipe attached to the nozzle. Measurements reveal that Reynolds number dictate the potential core length such that the higher the Reynolds number, the lower the potential core which is a measure of mixing of jet and ambient fluid. It shows that further away from the jet exit section, potential core decreases as Reynolds number increases, the velocity profile has a top hat shape very close to the nozzle exit and the shape is independent of Reynolds number. It is found that potential core extends up to x/d=8 for Reynolds number of 1140 as against conventional near field 0≤x/d≤6. This may suggest effect of very low Reynolds number. However, further investigation is required to ascertain this at extremely low Reynolds numbers. It is also observed that further away from the jet exit section, the higher the downstream distance, the higher the jet half-width (R1/2). Furthermore, the flow in the pipe shows almost constant value of normalised axial centerline velocity for a longer distance and this clearly indicates that there is mass redistribution rather than entrainment of ambient fluid. Overall, the Reynolds number controls the magnitude rather than the wavelength of the oscillation


  • Open Access

    Modeling of natural convection of a concentrated solar power receiver absorber tube in interaction with neighbouring absorbers

    by Olanrewaju Miracle Oyewola, Niyi Ezekiel Olukayode, Olusegun Olufemi Ajide

    Concentrated Solar Power (CSP) technology stands out among other renewable energy sources not only because of its ability to address current energy security and environmental challenges but because its energy can be stored for future use. To ensure optimum performance in this system, the heat losses need to be evaluated for better design. This work studies the natural convection in the receiver absorber tube of a CSP plant taking into consideration the influence of neighboring absorbers. A 2-Dimensional model was adopted in this study. Initially, a single absorber tube was considered, it was subjected to heat flux at the top wall, the bottom wall was insulated and a temperature differential was set up at the lateral walls. The dimensionless forms of Navier-Stokes and energy equations were solved using the finite element formulation of COMSOL Multiphysics software. The result obtained for a single absorber tube showed good agreement with existing research works. This validated model was then extended to multiple absorber tubes (two to six absorber tubes). On the basis of the study, there is an observed increase in the intensity and dominance of convective heat transfer with an increase in the number of absorber tubes. This is occasioned by an increase in the average surface temperature as well as average Nusselt number. For the Rayleigh number of 104, 105 and 106, the average Nusselt number increases with the number of absorber tubes by 13.87 %, 6.26 %, and 1.55 %, respectively. This increment suggests effect of thermal interactions among the neighboring absorber tubes