Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Ruixian Ma has a total of 63 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Vibration analysis of a micro turbojet engine under two impeller structural faults

    by Zhiming Yang, Ruixian Ma, Yongkui Lei, Linyuan Jia, Sara Alseiari, Heba Youssef, Maryam AlMheiri

    Disk fracture and locking nut loosening of centrifugal impeller leads to severe vibration of micro turbojet engines, posing significant threats to engine stability and safety. In order to identify the engine vibration characteristics induced by the above two faults in a practical micro aero-engine, vibration acceleration of the engine casing is collected and analysed comprehensively both in time and frequency domain. The order tracking resampling method is applied to analyse the transient vibration response. The vibration trend during the pre- and post-fault phases is assessed from the perspective of root mean square (RMS) value of the vibration velocity. In time domain, a transient phase is observed when the structural faults occur, followed by a steady state phase. For the disk fracture case, the vibration amplitude at the rotating frequency (RF, 1×) is increased significantly. On the contrary, the amplitude at the blade passing frequency (BPF, 7×) is decreased slightly. Furthermore, the presence of subharmonic components is captured in the transient phase, which reflects the re-balance of flow in the impeller. A frequency modulation between the BPF and the RF is detected in the steady state. As for the nut-loosening fault, the vibration of 1× and 3× components is increased, while the 7× amplitude remains almost unchanged. The RMS value of vibration velocity in the post-fault steady state is much higher than that of normal state for both fault conditions.

  • Modelling method for bending stiffness of bolted flange joint with spigot and analysis of rotor vibration characteristics

    by Yu Li, Siji Wang, Haitao Guan, Liang Hong, Qingyang Shen, Quankun Li, Lu Zhao, Ruixian Ma, Zhongliang Xie

  • Open Access

    Modelling method for bending stiffness of bolted flange joint with spigot and analysis of rotor vibration characteristics

    by Yu Li, Siji Wang, Haitao Guan, Liang Hong, Qingyang Shen, Quankun Li, Lu Zhao, Ruixian Ma, Zhongliang Xie

    To meet the rapid iteration requirements of the bolted rotor system for the next-generation aero-engine in the conceptual design phase, the bending stiffness model of the bolted joint is required to have the characteristics of high accuracy and easy solvability. A new analytical model of bending stiffness for bolted flange joint with spigot considering all parameters is established based on the theory of plates and shells, and the effects of preload and preload unevenness on the bending stiffness are analyzed. By performing a comparison study with the finite contact element model, the maximal calculation error of the bending stiffness is approximately 6.83%, and the time required to calculate the bending stiffness once is reduced from 7 minutes to 5e-5 second, the accuracy and efficiency of the proposed model is validated. After that, an equivalent method for characterizing bolted joint using virtual shaft segment is proposed, and a dynamical model of the bolted rotor system is developed, in which the proposed bending stiffness model is introduced. The influence of preload and preload unevenness on the vibration characteristics of the bolted rotor system are analyzed by combining numerical calculation and experimental investigation. The results show that increasing preload can narrow the nonsynchronous response interval of the bolted rotor system and reduce the proportion of strain energy for the bolted joint, the amplitude of subcritical self-excited vibration decreases with the reduction of preload unevenness.

  • Simulation Analysis of Stiffness and Strength Characteristics of Curvic Couplings

    by Xin Wang, Xinliang Lei, Tianlong Wang, Shiyong Qin, Ruixian Ma, Siji Wang, Mingfu Liao


  • Optimization Design of an Active Elastic Support/Dry Friction Damper for Aero-engine Rotor Systems

    by Northwestern Polytechnical University, Siji Wang, Dafang Lin, Quankun Li, Ruixian Ma, Xingcheng Xie, Jiahao Yang

    To improve damper’s performance in the vicinity of dual-rotor systems’ multiple critical speeds, an optimization design method is proposed in this paper. Firstly, an active elastic support/dry friction damper (ESDFD) is investigated for damping vibration of the dual-rotor system. A dynamic model of the dual-rotor system with ESDFDs is built by the finite element method. Then, the effect of the ESDFD on the dual-rotor dynamic characteristics is analysed. Importantly, through numerical study, relationships between the damping performance of the ESDFD and the rotor’s modes are shown. And the squirrel cage support stiffness is selected as the optimization variable. Based on this, the optimization objective function is constructed by considering the critical speed constraint, sensitivity of unbalance, and controllability of the damper. Finally, the optimization parameters are obtained by the improved particle swarm optimization algorithm. And the simulation results show that the dual-rotor is less sensitive to the unbalance and the damper’s controllability significantly improves. Keywords: elastic support/dry friction damper; vibration control; dual-rotor system; optimization design; improved particle swarm algorithm


  • Open Access

    Research on the Power Output of Different Floating Wind Farms Considering the Wake Effect

    by Jiaping Cui, Xianyou Wu, Pin Lyu, Tong Zhao, Quankun Li, Ruixian Ma, Yingming Liu

    For floating wind turbines, one of the most interesting and challenging issues is that the movement of the rotor is strongly related to its floating platform, which results in corresponding variations in the wake characteristics of the turbine. Because the aerodynamic efficiency of the downstream turbines is affected by the wake characteristics, the power output will consequently vary depending on the different types of floating wind turbines and floating wind farms used. In this study, the rotor movement, wake characteristics, and corresponding wind farm power output are analyzed using a numerical method for three typical floating wind turbines: the semisubmersible type, spar buoy type, and tension leg platform type with a 5 MW configuration. A fixed-bottom monopile wind turbine is adopted as a benchmark. The simulation results show that of the three floating wind turbines, the rotor position and wake center are most dispersed in the case of the spar buoy type, and its wake also has the lowest impact on downstream wind turbines. Additionally, the power output of the corresponding spar buoy type wind farm is also the highest at different wind speeds, followed by the semisubmersible type, tension leg platform type, and then the fixed-bottom type. In particular, at low wind speeds, the wake effects differ significantly among the various types of wind turbines.


  • Open Access

    Research on the Blades and Performance of Semi-Submersible Wind Turbines with Different Capacities

    by Jiaping Cui, Zhigang Cao, Pin Lyu, Huaiwu Peng, Quankun Li, Ruixian Ma, Yingming Liu

    With the gradual increase in the maturity of wind energy technology, floating offshore wind turbines have progressively moved from small-capacity demonstrations to large-capacity commercial applications. As a direct component of wind turbines used to capture wind energy, an increase in the blade length directly leads to an increase in blade flexibility and a decrease in aerodynamic performance. Furthermore, if the floater has an additional six degrees of freedom, the movement and load of the blade under the combined action of wind and waves are more complicated. In this work, two types of semi-submersible wind turbines with different capacities are used as the research objects, and the load and motion characteristics of the blades of these floating offshore wind turbines are studied. Through the analysis of the simulation data, the following conclusions are drawn: with the increase in the capacity of the wind turbine, the flexible deformation of the blade increases, the movement range of the blade tip becomes larger, the blade root load increases, and the power fluctuation is more obvious. Compared with the bottom-fixed wind turbine, the flexible blade deformation of the floating offshore wind turbine is smaller; however, the blade root load is more dispersed, and the power output is more unstable and lower.