Mansura Sadek
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mansura Sadek has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Rongming Chu
Department of Electrical and Computer Engineering, University of Illinois Urbana-Champaign 6 , Urbana, Illinois 61801
8 shared publications - Jianan Song
Department of Electrical Engineering, The Pennsylvania State University 1 , University Park, Pennsylvania 16802
6 shared publications - Jesse T. Kemmerling
Department of Electrical Engineering, Pennsylvania State University, University Park, PA, USA
5 shared publications - Rian Guan
Department of Electrical Engineering, The Pennsylvania State University, University Park, PA, USA
5 shared publications - Sang-Woo Han
Department of Electrical Engineering, The Pennsylvania State University, University Park, PA, USA
5 shared publications - Yixin Xiong
Department of Electrical Engineering, The Pennsylvania State University 1 , University Park, Pennsylvania 16802
5 shared publications
Latest Publications
- Open Access
- 12 August 2026
- Published by AIP Publishing in APL Electronic Devices
- Vol. 2 (3)
High current density and low on-resistance in ultra-wide bandgap Al0.65Ga0.35N-channel MOS-HEMTs for kV power switching
Achieving high on-currents (ID,MAX) and low on-resistances (RON) is a cardinal challenge for ultra-wide bandgap (UWBG) semiconductor materials, such as Al-rich AlxGa1−xN. In this work, we demonstrate state-of-the-art ID,MAX and RON (450 mA/mm and 30.5 Ω mm for LSD = 10 μm) in UWBG Al0.85Ga0.15N/Al0.65Ga0.35N channel high electron mobility transistors. We demonstrate the first microscopic imaging of ohmic contacts to reverse-graded AlxGa1−xN heterostructures and demonstrate high-performance power transistors with a Baliga figure of merit of 629 MW/cm2. We further characterize the high temperature breakdown of these device structures up to 150 °C, showing that high breakdown voltages are maintained with low degradation in RON. Cumulatively, these results show the potential of AlxGa1−xN-channel HEMTs for high voltage and high temperature applications.
- 12 August 2026
- Published by AIP Publishing in APL Electronic Devices
- Vol. 2 (3)
Open AccessHigh current density and low on-resistance in ultra-wide bandgap Al0.65Ga0.35N-channel MOS-HEMTs for kV power switching
Achieving high on-currents (ID,MAX) and low on-resistances (RON) is a cardinal challenge for ultra-wide bandgap (UWBG) semiconductor materials, such as Al-rich AlxGa1−xN. In this work, we demonstrate state-of-the-art ID,MAX and RON (450 mA/mm and 30.5 Ω mm for LSD = 10 μm) in UWBG Al0.85Ga0.15N/Al0.65Ga0.35N channel high electron mobility transistors. We demonstrate the first microscopic imaging of ohmic contacts to reverse-graded AlxGa1−xN heterostructures and demonstrate high-performance power transistors with a Baliga figure of merit of 629 MW/cm2. We further characterize the high temperature breakdown of these device structures up to 150 °C, showing that high breakdown voltages are maintained with low degradation in RON. Cumulatively, these results show the potential of AlxGa1−xN-channel HEMTs for high voltage and high temperature applications.
- Open Access
- 27 July 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (4)
Regrown n++-GaN ohmic contacts to high-Al content AlxGa1−xN (x > 0.6) digital alloy channels using AlN/GaN short-period superlattice
In this paper, we report a novel ohmic contact formation scheme for extreme bandgap AlxGa1−xN (x > 0.6) channel high electron mobility transistors with undoped barrier layers. Our approach consists of using a new low-temperature pulsed metal-organic chemical vapor deposition doping scheme for the n++-GaN regrown contacts and an AlxGa1−xN digital alloy (DA) channel layer comprising short-period superlattices of AlN and GaN. Pulsed growth and doping yield a sheet resistivity that is a factor of 3–5 lower than that of conventional doped n++-GaN layers grown under identical conditions. Moreover, the regrown n++-GaN layer has no hetero-barrier with the GaN layers of the DA channel, which leads to linear ohmic contacts and a record low contact resistance Rc ∼ 6.5 Ω-mm to the Al0.62Ga0.38N DA channel layer of a HEMT with an AlN barrier layer.
- 27 July 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (4)
Open AccessRegrown n++-GaN ohmic contacts to high-Al content AlxGa1−xN (x > 0.6) digital alloy channels using AlN/GaN short-period superlattice
In this paper, we report a novel ohmic contact formation scheme for extreme bandgap AlxGa1−xN (x > 0.6) channel high electron mobility transistors with undoped barrier layers. Our approach consists of using a new low-temperature pulsed metal-organic chemical vapor deposition doping scheme for the n++-GaN regrown contacts and an AlxGa1−xN digital alloy (DA) channel layer comprising short-period superlattices of AlN and GaN. Pulsed growth and doping yield a sheet resistivity that is a factor of 3–5 lower than that of conventional doped n++-GaN layers grown under identical conditions. Moreover, the regrown n++-GaN layer has no hetero-barrier with the GaN layers of the DA channel, which leads to linear ohmic contacts and a record low contact resistance Rc ∼ 6.5 Ω-mm to the Al0.62Ga0.38N DA channel layer of a HEMT with an AlN barrier layer.
- Open Access
- 1 May 2025
- Published by AIP Publishing in APL Materials
- Vol. 13 (5)
Field-dependent carrier transport in implanted isolation region of GaN lateral power devices
Among GaN lateral power devices, with proper E-field management, the breakdown occurs in the device isolation region rather than the active region. In this paper, we investigate field-dependent carrier transport in the isolation structures. Isolation test structures with variations in buffer doping, un-intentionally doped (UID) GaN thickness, and implantation conditions were fabricated. Electrical characterization was performed over a wide range of voltage and temperature. With varying UID GaN thickness and buffer doping, the leakage current and breakdown characteristics remain the same for a specific implantation condition, indicating that the leakage conduction and breakdown are governed by the implanted GaN region. Analysis of the temperature-dependent I–V reveals that carrier transport in the implanted GaN can be well explained by hopping conduction, involving three distinctive regions of operation depending on the E-field. At low E-field, carrier transport is ohmic, consistent with variable range hopping, driven by thermal activation. At medium E-field, a field enhanced thermally activated hopping is observed, following σ ∼ σ(T)exp(E). At high E-field, activation-less hopping is visible, following σ ∼ exp(−1/E), which occurs above a critical E-field limited by localization length.
- 1 May 2025
- Published by AIP Publishing in APL Materials
- Vol. 13 (5)
Open AccessField-dependent carrier transport in implanted isolation region of GaN lateral power devices
Among GaN lateral power devices, with proper E-field management, the breakdown occurs in the device isolation region rather than the active region. In this paper, we investigate field-dependent carrier transport in the isolation structures. Isolation test structures with variations in buffer doping, un-intentionally doped (UID) GaN thickness, and implantation conditions were fabricated. Electrical characterization was performed over a wide range of voltage and temperature. With varying UID GaN thickness and buffer doping, the leakage current and breakdown characteristics remain the same for a specific implantation condition, indicating that the leakage conduction and breakdown are governed by the implanted GaN region. Analysis of the temperature-dependent I–V reveals that carrier transport in the implanted GaN can be well explained by hopping conduction, involving three distinctive regions of operation depending on the E-field. At low E-field, carrier transport is ohmic, consistent with variable range hopping, driven by thermal activation. At medium E-field, a field enhanced thermally activated hopping is observed, following σ ∼ σ(T)exp(E). At high E-field, activation-less hopping is visible, following σ ∼ exp(−1/E), which occurs above a critical E-field limited by localization length.
- Top Cited PapersOpen Access
- 24 February 2025
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 40 (3) , 033002
Recent advances in GaN-based power devices and integration
Gallium nitride (GaN) has gained traction in replacing silicon for power electronics applications, due to its high breakdown field, high mobility 2D electron gas, and effective n/p-type doping. This paper reviews three important topics of GaN power devices. One is the voltage-blocking structures needed to operate at high voltage while minimizing conduction loss and switching loss. Another one is the structure used to achieve normally-off operation, which is often required for power electronics. The third topic is the monolithic integration of gate drivers and power switches to achieve the ultimate switching speed at a low cost.
- 24 February 2025
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 40 (3) , 033002
Top Cited PapersOpen AccessRecent advances in GaN-based power devices and integration
Gallium nitride (GaN) has gained traction in replacing silicon for power electronics applications, due to its high breakdown field, high mobility 2D electron gas, and effective n/p-type doping. This paper reviews three important topics of GaN power devices. One is the voltage-blocking structures needed to operate at high voltage while minimizing conduction loss and switching loss. Another one is the structure used to achieve normally-off operation, which is often required for power electronics. The third topic is the monolithic integration of gate drivers and power switches to achieve the ultimate switching speed at a low cost.
- 24 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (11) , 6915-6920
Leakage Current and Breakdown Characteristics of Isolation in Gallium Nitride Lateral Power Devices
In gallium nitride (GaN) lateral power devices with advanced E-field management, isolation becomes a bottleneck for achieving higher breakdown voltage (BV). To understand the physical mechanism of isolation, the experimental analysis of isolation structures is done in this work. This article presents the measured leakage current and breakdown characteristics of isolation structures, compatible with lateral devices. For unimplanted isolation structures, leakage is injection barrier limited and breakdown is by surface punchthrough. BV has a quadratic dependence on the isolation length. Ion implantation introduces trap-limited hopping conduction, marked by the exponentially field-dependent conductance. After implantation, despite an increase in leakage current, BV increases drastically. The dependence of BV on isolation length changes from quadratic in unimplanted isolation to linear in implanted one due to flattening of E-field. To achieve high BV in GaN lateral power devices, the implanted isolation structure is preferred at the cost of high isolation leakage.
- 24 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (11) , 6915-6920
Leakage Current and Breakdown Characteristics of Isolation in Gallium Nitride Lateral Power Devices
In gallium nitride (GaN) lateral power devices with advanced E-field management, isolation becomes a bottleneck for achieving higher breakdown voltage (BV). To understand the physical mechanism of isolation, the experimental analysis of isolation structures is done in this work. This article presents the measured leakage current and breakdown characteristics of isolation structures, compatible with lateral devices. For unimplanted isolation structures, leakage is injection barrier limited and breakdown is by surface punchthrough. BV has a quadratic dependence on the isolation length. Ion implantation introduces trap-limited hopping conduction, marked by the exponentially field-dependent conductance. After implantation, despite an increase in leakage current, BV increases drastically. The dependence of BV on isolation length changes from quadratic in unimplanted isolation to linear in implanted one due to flattening of E-field. To achieve high BV in GaN lateral power devices, the implanted isolation structure is preferred at the cost of high isolation leakage.
- 30 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 45 (7) , 1161-1164
Monolithically Integrated GaN Photodetector and Bootstrapping Transimpedance Amplifier
Monolithic integration of photodetector and transimpedance amplifier is demonstrated for galvanically isolated control of GaN power switches. The transimpedance amplifier includes a bootstrapping comparator and an optical receiver stage. The bootstrapping comparator features depletion-mode AlGaN/GaN high electron mobility transistors for optimized speed and input common mode range spanning from -1 to 8 V. The comparator delivers a voltage gain up to 176 V/V and a unity-gain bandwidth of 3.58 MHz. Within the optical receiver stage, the photodetector exhibits a photocurrent range of 50 to 100 nA when stimulated by a 340 nm wavelength light emitting diode. Together with a 330 kΩ pull-up resistor, the optical receiver stage generates a voltage signal ranging from 16.5 to 33 mV. The signal is then amplified by the bootstrapping comparator, resulting in an output voltage signal with a peak-to-peak voltage of 3.1 V, operating at 1 kHz frequency.
- 30 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 45 (7) , 1161-1164
Monolithically Integrated GaN Photodetector and Bootstrapping Transimpedance Amplifier
Monolithic integration of photodetector and transimpedance amplifier is demonstrated for galvanically isolated control of GaN power switches. The transimpedance amplifier includes a bootstrapping comparator and an optical receiver stage. The bootstrapping comparator features depletion-mode AlGaN/GaN high electron mobility transistors for optimized speed and input common mode range spanning from -1 to 8 V. The comparator delivers a voltage gain up to 176 V/V and a unity-gain bandwidth of 3.58 MHz. Within the optical receiver stage, the photodetector exhibits a photocurrent range of 50 to 100 nA when stimulated by a 340 nm wavelength light emitting diode. Together with a 330 kΩ pull-up resistor, the optical receiver stage generates a voltage signal ranging from 16.5 to 33 mV. The signal is then amplified by the bootstrapping comparator, resulting in an output voltage signal with a peak-to-peak voltage of 3.1 V, operating at 1 kHz frequency.
- 2 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (2) , 1153-1159
GaN Super-Heterojunction FETs With 10-kV Blocking and 3-kV Dynamic Switching
This article reports on two generations of GaN-on-sapphire super-heterojunction (SHJ) transistors, aiming at the realization of 10-kV class power transistors with low static and dynamic ON-resistance. First generation (Gen. 1) GaN SHJ-FETs used a single 2-D electron gas (2DEG) channel design with Schottky gate. Experimental results indicated the feasibility of achieving 10-kV blocking, however, room for improvement to reduce static source-to-drain ON-resistance${R}_{\text {DS},\text {ON}}$ and dynamic${R}_{\text {DS},\text {ON}}$ degradation. A second generation (Gen. 2) SHJ-MOSFET was designed using an epitaxy with two 2DEG channels for larger ON-state drain current and smaller${R}_{\text {DS},\text {ON}}$ . The high-voltage capability and dynamic${R}_{\text {DS},\text {ON}}$ degradation mitigation were reached by implementing the GaN SHJ design, while simultaneously avoiding surface trapping between the gate and the SHJ structure. Gen. 2 experimentally showed scaling of blocking voltage with SHJ length up to 10 kV, reduced static${R}_{\text {DS},\text {ON}}$ of$71.4~\Omega \cdot $ mm (73.5$\text{m}\Omega \cdot $ cm$^{{2}}{)}$ , low${R}_{\text {DS,ON}}{C}_{\mathrm {O(}\mathrm {tr})}$ of ~4.9 ps, and controlled current collapse of 123% when switched from an OFF-state bias of 3 kV.- 2 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (2) , 1153-1159
GaN Super-Heterojunction FETs With 10-kV Blocking and 3-kV Dynamic Switching
This article reports on two generations of GaN-on-sapphire super-heterojunction (SHJ) transistors, aiming at the realization of 10-kV class power transistors with low static and dynamic ON-resistance. First generation (Gen. 1) GaN SHJ-FETs used a single 2-D electron gas (2DEG) channel design with Schottky gate. Experimental results indicated the feasibility of achieving 10-kV blocking, however, room for improvement to reduce static source-to-drain ON-resistance${R}_{\text {DS},\text {ON}}$ and dynamic${R}_{\text {DS},\text {ON}}$ degradation. A second generation (Gen. 2) SHJ-MOSFET was designed using an epitaxy with two 2DEG channels for larger ON-state drain current and smaller${R}_{\text {DS},\text {ON}}$ . The high-voltage capability and dynamic${R}_{\text {DS},\text {ON}}$ degradation mitigation were reached by implementing the GaN SHJ design, while simultaneously avoiding surface trapping between the gate and the SHJ structure. Gen. 2 experimentally showed scaling of blocking voltage with SHJ length up to 10 kV, reduced static${R}_{\text {DS},\text {ON}}$ of$71.4~\Omega \cdot $ mm (73.5$\text{m}\Omega \cdot $ cm$^{{2}}{)}$ , low${R}_{\text {DS,ON}}{C}_{\mathrm {O(}\mathrm {tr})}$ of ~4.9 ps, and controlled current collapse of 123% when switched from an OFF-state bias of 3 kV.- 29 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 43 (5) , 701-704
Impact of Charge Balance on Static and Dynamic Characteristics of GaN Super-Heterojunction Schottky Barrier Diodes
This letter reports the first controlled experimental study on the impact of charge-balance on static and dynamic characteristics of GaN super-heterojunction Schottky barrier diodes (SHJ-SBD). Charge balance between p- and n-type doped GaN for reducing peak E-field can be optimized via charge-balance etching (CBE) of the p-GaN SHJ region to improve dynamic ${R}_{\textit {ON}}$ degradation and breakdown voltage (BV). Three CBE conditions were fabricated with the same process on a single epitaxial wafer to mitigate process dependent variation. Charge-balance varied from donor-rich (thinner p-GaN) to near-optimum charge-balance condition, which enabled excellent dynamic ${R}_{\textit {ON}}$ degradation of 16.9% at 3 kV and BV greater than 10 kV without field plate. TCAD simulation reinforces understanding showing CBE effect on E-Field redistribution and reduced peak E-field.
- 29 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 43 (5) , 701-704
Impact of Charge Balance on Static and Dynamic Characteristics of GaN Super-Heterojunction Schottky Barrier Diodes
This letter reports the first controlled experimental study on the impact of charge-balance on static and dynamic characteristics of GaN super-heterojunction Schottky barrier diodes (SHJ-SBD). Charge balance between p- and n-type doped GaN for reducing peak E-field can be optimized via charge-balance etching (CBE) of the p-GaN SHJ region to improve dynamic ${R}_{\textit {ON}}$ degradation and breakdown voltage (BV). Three CBE conditions were fabricated with the same process on a single epitaxial wafer to mitigate process dependent variation. Charge-balance varied from donor-rich (thinner p-GaN) to near-optimum charge-balance condition, which enabled excellent dynamic ${R}_{\textit {ON}}$ degradation of 16.9% at 3 kV and BV greater than 10 kV without field plate. TCAD simulation reinforces understanding showing CBE effect on E-Field redistribution and reduced peak E-field.
- 15 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (4) , 1912-1917
High-Temperature Static and Dynamic Characteristics of 4.2-kV GaN Super-Heterojunction p-n Diodes
This article presents the static and dynamic characterization of 4.2-kV super-junction p-n diodes at high temperatures. Reduction of the forward current with increasing temperature is consistent with 2DEG mobility degradation caused by polar optical phonon scattering. Reverse leakage current was dominated by isolation leakage, with an activation energy of ~0.26 eV, close to the reported activation energy of surface leakage. Dynamic switching characterization in the temperature range from room temperature (RT) to 300 °C showed a nonmonotonic dependence of dynamic ON-resistance on temperature. At room temperature and 50 °C, devices showed zero current collapse (CC) up to OFF-state stress bias of 3 kV at 100 $\mu \text{s}$ timescale. Between 100 °C and 200 °C, significant CC was observed. From 250 °C to 300 °C, devices showed recovery from the severe CC. The degradation and recovery of dynamic ON-resistance can be explained by emission and recapture of holes during the OFF- and ON-states, respectively.
- 15 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (4) , 1912-1917
High-Temperature Static and Dynamic Characteristics of 4.2-kV GaN Super-Heterojunction p-n Diodes
This article presents the static and dynamic characterization of 4.2-kV super-junction p-n diodes at high temperatures. Reduction of the forward current with increasing temperature is consistent with 2DEG mobility degradation caused by polar optical phonon scattering. Reverse leakage current was dominated by isolation leakage, with an activation energy of ~0.26 eV, close to the reported activation energy of surface leakage. Dynamic switching characterization in the temperature range from room temperature (RT) to 300 °C showed a nonmonotonic dependence of dynamic ON-resistance on temperature. At room temperature and 50 °C, devices showed zero current collapse (CC) up to OFF-state stress bias of 3 kV at 100 $\mu \text{s}$ timescale. Between 100 °C and 200 °C, significant CC was observed. From 250 °C to 300 °C, devices showed recovery from the severe CC. The degradation and recovery of dynamic ON-resistance can be explained by emission and recapture of holes during the OFF- and ON-states, respectively.
- 24 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (11) , 5736-5741
12.5 kV GaN Super-Heterojunction Schottky Barrier Diodes
This article reports GaN super-heterojunction Schottky barrier diodes (SHJ-SBDs) with substantially improved performance. Metal-2DEG sidewall n-ohmic contacts were deployed to achieve low contact resistance of $0.75~\Omega ~ \cdot ~mm$ , avoiding the risk of abnormally high contact resistance caused by inaccurate etch depth control. A pGaN notch formed near the cathode successfully eliminated excessive hole conduction caused by the sidewall n-ohmic contact. Isolation was improved by a high-energy Al implantation step. The resulting SHJ-SBD exhibited a breakdown voltage (BV) of ~12.5 kV and a specific resistance of 100.8 $\text{m}\Omega ~ \cdot ~cm^{2}$ .
- 24 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (11) , 5736-5741
12.5 kV GaN Super-Heterojunction Schottky Barrier Diodes
This article reports GaN super-heterojunction Schottky barrier diodes (SHJ-SBDs) with substantially improved performance. Metal-2DEG sidewall n-ohmic contacts were deployed to achieve low contact resistance of $0.75~\Omega ~ \cdot ~mm$ , avoiding the risk of abnormally high contact resistance caused by inaccurate etch depth control. A pGaN notch formed near the cathode successfully eliminated excessive hole conduction caused by the sidewall n-ohmic contact. Isolation was improved by a high-energy Al implantation step. The resulting SHJ-SBD exhibited a breakdown voltage (BV) of ~12.5 kV and a specific resistance of 100.8 $\text{m}\Omega ~ \cdot ~cm^{2}$ .