Julius Maximilian Placzek
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Julius Maximilian Placzek has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Hamzeh Beiranvand
Faculty of Engineering, Kiel University, Kiel, Germany
2 shared publications - Marco Liserre
Kiel University
2 shared publications - Maurice Hott
Faculty of Engineering, Kiel University, Kiel, Germany
2 shared publications - Peter Adam Hoeher
Faculty of Engineering, Kiel University, Kiel, Germany
2 shared publications - Andrej Harlakin
Department of Electrical and Information Engineering, Kiel University, Kiel, Germany
1 shared publication Cedric Isokeit
Institute of Computer Engineering, Luebeck University, Luebeck, Germany
1 shared publication
Latest Publications
- 22 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (9) , 15325-15339
Planar Transformer With Integrated Direct Liquid Cooling
Planar transformers (PTs) are becoming increasingly popular due to the growing demand for compact medium frequency transformers in electric vehicles (EVs) and data centres. Reducing the size of such converters by increasing the power density of the PT remains the most significant challenge. In particular, thermal management of the internal printed circuit board (PCB) layers, which are difficult to access for cooling, poses the primary limitation. Therefore, this paper proposes three integrated direct liquid cooling methods for the PT layer stack. The first uses an additional hollow copper conductor as a cooling channel and the second uses a plastic spacer with a channel for coolant guidance. In these designs, the liquid flows inside the hollow copper conductor and, for the plastic spacer, comes into direct contact with the winding layers. Due to the nature of the copper conductor, additional losses will be induced. As current models cannot correctly predict losses in rectangular hollow conductors, a novel closed form solution has been developed to evaluate additional losses for efficiency and optimal placement. Additionally, the conductor thickness and channel height are optimized to achieve the best thermal performance. Then, a 1D thermal network is developed to estimate the possible temperature reduction of the proposed solutions. The proposed solutions are then compared, and the use of a hollow conductor as an active turn with cooling for high current capability is introduced as a third solution to reduce losses and the problem of current sharing in high current systems with many parallel layers. An experimental setup was built to validate the proposed cooling solutions and a temperature reduction of 54 % was achieved.
- 22 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (9) , 15325-15339
Planar Transformer With Integrated Direct Liquid Cooling
Planar transformers (PTs) are becoming increasingly popular due to the growing demand for compact medium frequency transformers in electric vehicles (EVs) and data centres. Reducing the size of such converters by increasing the power density of the PT remains the most significant challenge. In particular, thermal management of the internal printed circuit board (PCB) layers, which are difficult to access for cooling, poses the primary limitation. Therefore, this paper proposes three integrated direct liquid cooling methods for the PT layer stack. The first uses an additional hollow copper conductor as a cooling channel and the second uses a plastic spacer with a channel for coolant guidance. In these designs, the liquid flows inside the hollow copper conductor and, for the plastic spacer, comes into direct contact with the winding layers. Due to the nature of the copper conductor, additional losses will be induced. As current models cannot correctly predict losses in rectangular hollow conductors, a novel closed form solution has been developed to evaluate additional losses for efficiency and optimal placement. Additionally, the conductor thickness and channel height are optimized to achieve the best thermal performance. Then, a 1D thermal network is developed to estimate the possible temperature reduction of the proposed solutions. The proposed solutions are then compared, and the use of a hollow conductor as an active turn with cooling for high current capability is introduced as a third solution to reduce losses and the problem of current sharing in high current systems with many parallel layers. An experimental setup was built to validate the proposed cooling solutions and a temperature reduction of 54 % was achieved.
- Open Access
- 5 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Oceanic Engineering
- Vol. 50 (1) , 228-251
Multiheterogeneous AUV Swarm Technology Exemplified by the MAUS Project: Cooperation, Mission Planning and Hybrid Communication
The mobile autonomous underwater system (MAUS) aims to create next-generation vehicles, focusing on improved intelligence, mission operations, and application scenarios. Accordingly, two types of autonomous underwater vehicles (AUVs) have been developed to operate and collaborate in various applications. The first AUV, named “Hansel,” has hovering capabilities and is tailored to tasks, such as object inspection and detection. The second AUV, called “Gretel,” has going capabilities and is suitable for tasks, such as seafloor mapping. The two AUV types are equipped with different sensors, allowing them to perform distinct tasks simultaneously as a team. The going AUV has a robust navigation system that includes an inertial navigation system, an ultra-short baseline unit, and a Doppler velocity log for dead reckoning. In contrast, the hovering AUV only has a low-cost micro-electro-mechanical system. Gretel's navigation unit improves Hansel's navigation, along with data transfer between the vehicles. The AUVs rely on a hybrid communication system that integrates acoustic, inductive, and optical links to combine the strengths of each technology. To accomplish their individual goals, the AUVs participate in joint mission planning, utilizing a variety of sensors and tasks that are specific to each AUV. This approach is commonly referred to as multiheterogeneous AUV swarm technology. The multiheterogeneous concept developed in the MAUS project was experimentally validated in Kiel Fjord, located in the southwest Baltic Sea, and in La Spezia, Mediterranean Sea.
- 5 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Oceanic Engineering
- Vol. 50 (1) , 228-251
Open AccessMultiheterogeneous AUV Swarm Technology Exemplified by the MAUS Project: Cooperation, Mission Planning and Hybrid Communication
The mobile autonomous underwater system (MAUS) aims to create next-generation vehicles, focusing on improved intelligence, mission operations, and application scenarios. Accordingly, two types of autonomous underwater vehicles (AUVs) have been developed to operate and collaborate in various applications. The first AUV, named “Hansel,” has hovering capabilities and is tailored to tasks, such as object inspection and detection. The second AUV, called “Gretel,” has going capabilities and is suitable for tasks, such as seafloor mapping. The two AUV types are equipped with different sensors, allowing them to perform distinct tasks simultaneously as a team. The going AUV has a robust navigation system that includes an inertial navigation system, an ultra-short baseline unit, and a Doppler velocity log for dead reckoning. In contrast, the hovering AUV only has a low-cost micro-electro-mechanical system. Gretel's navigation unit improves Hansel's navigation, along with data transfer between the vehicles. The AUVs rely on a hybrid communication system that integrates acoustic, inductive, and optical links to combine the strengths of each technology. To accomplish their individual goals, the AUVs participate in joint mission planning, utilizing a variety of sensors and tasks that are specific to each AUV. This approach is commonly referred to as multiheterogeneous AUV swarm technology. The multiheterogeneous concept developed in the MAUS project was experimentally validated in Kiel Fjord, located in the southwest Baltic Sea, and in La Spezia, Mediterranean Sea.
- Open Access
- 15 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in TechRxiv
Nonintrusive Continuous Phase Frequency Shift Keying based Talkative Power Conversion for IPT
Communication is crucial for Dual Side Control (DSC) of Inductive Power Transfer (IPT), which uses multiple variables in two separate converters for efficiency optimization. To avoid add-on communication systems, this letter proposes to implement Talkative Power Conversion (TPC)-added utility communication by modulated power conversion without intrusive changes to hardware, control or power conversion. The secondary converter is used to transmit feedback information and the Phase Locked Loop (PLL) typical of synchronous DSC is relocated to the primary side as the receiver, avoiding hardware additions. Based on Continuous Phase Frequency Shift Keying (CPFSK), the communication process is then designed to act as quasi steady state to the power transfer and control processes. The strategy is demonstrated to actively close a DSC loop in experiment with an average frequency shift of only 0.15 Hz. No added perturbations are visible in time domain voltage or currents, which confirms the nonintrusive nature of the proposed method.
- 15 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in TechRxiv
Open AccessNonintrusive Continuous Phase Frequency Shift Keying based Talkative Power Conversion for IPT
Communication is crucial for Dual Side Control (DSC) of Inductive Power Transfer (IPT), which uses multiple variables in two separate converters for efficiency optimization. To avoid add-on communication systems, this letter proposes to implement Talkative Power Conversion (TPC)-added utility communication by modulated power conversion without intrusive changes to hardware, control or power conversion. The secondary converter is used to transmit feedback information and the Phase Locked Loop (PLL) typical of synchronous DSC is relocated to the primary side as the receiver, avoiding hardware additions. Based on Continuous Phase Frequency Shift Keying (CPFSK), the communication process is then designed to act as quasi steady state to the power transfer and control processes. The strategy is demonstrated to actively close a DSC loop in experiment with an average frequency shift of only 0.15 Hz. No added perturbations are visible in time domain voltage or currents, which confirms the nonintrusive nature of the proposed method.
- 13 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (6) , 7836-7847
Communicationless Phase Cooperative Control of Inductive Power Transfer Using Asymmetrical Modulations
Dual Side Control (DSC) of Inductive Power Transfer (IPT) generally requires communication between the system sides to coordinate the local controllers. For reduction of component count and operation in challenging environments such as underwater, communicationless DSC is beneficial. This article investigates if and how asymmetric modulations, known for their improved performance in IPT, can be applied to phase cooperative communicationless DSC. A per side separate steady-state model is derived and the selection criteria for modulation schemes to be suitable for phase cooperative control are determined. The crucial importance of bijective or unique phase behavior in modulations for this control scheme is identified and demonstrated. In comparison with phase modulation it is shown that Asymmetric Voltage Cancellation of full-bridges is not reliably applicable to phase cooperative DSC, but asymmetrical modulation of half-bridges is. Therefore, a phase cooperative half-bridge DSC system as a simplified low complexity DSC scheme is further investigated and the load step regulation boundary derived. Analysis is verified in experiment and simulation, demonstrating ZVS behavior, dynamic load step regulation, the impact of harmonics on magnetics losses for high coupling and the impact of variable voltage ratio.
- 13 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (6) , 7836-7847
Communicationless Phase Cooperative Control of Inductive Power Transfer Using Asymmetrical Modulations
Dual Side Control (DSC) of Inductive Power Transfer (IPT) generally requires communication between the system sides to coordinate the local controllers. For reduction of component count and operation in challenging environments such as underwater, communicationless DSC is beneficial. This article investigates if and how asymmetric modulations, known for their improved performance in IPT, can be applied to phase cooperative communicationless DSC. A per side separate steady-state model is derived and the selection criteria for modulation schemes to be suitable for phase cooperative control are determined. The crucial importance of bijective or unique phase behavior in modulations for this control scheme is identified and demonstrated. In comparison with phase modulation it is shown that Asymmetric Voltage Cancellation of full-bridges is not reliably applicable to phase cooperative DSC, but asymmetrical modulation of half-bridges is. Therefore, a phase cooperative half-bridge DSC system as a simplified low complexity DSC scheme is further investigated and the load step regulation boundary derived. Analysis is verified in experiment and simulation, demonstrating ZVS behavior, dynamic load step regulation, the impact of harmonics on magnetics losses for high coupling and the impact of variable voltage ratio.
- Open Access
- 15 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 129431-129442
Multi-Resonant Frequency Shift Keying: A Novel and Efficient Modulation Scheme for Magnetic Communication
Magnetic communication is a promising technique in harsh environments, such as seawater. To enable efficient communication, transmitting and receiving coils are conventionally operated as part of resonant circuits. However, this results in narrow bandwidths and the associated disadvantages. Thus, most digital modulation schemes cannot be used efficiently on these systems. In this contribution, a mixed hardware/software approach for efficient frequency shift keying is presented. With this energy-efficient modulation concept, the full available bandwidth of a receiver can be utilized for data transmission, while all advantages of using a resonant circuit on the transmitter side can be retained. Towards this goal, a transmitter-side resonant circuit is designed, which supports discrete switching between multiple resonant frequencies. The data symbols are mapped onto these unique resonant frequencies. This prevents the parasitic amplitude modulation associated with conventional frequency shift keying applied to narrow bandwidth circuits, resulting in maximum transmitted magnitude and minimum symbol distortion without need for any further measures. Furthermore, the frequency spacing and/or the cardinality of the symbol alphabet can be increased considerably. At the receiver side, the classical pick-up coil is replaced by a high-sensitivity broadband magnetic field sensor. Numerical results of the mixed hardware/software scheme are provided, and are verified by an experimental setup. This setup is constructed using principles from the field of power electronics and demonstrates, how this modulation concept can be implemented with relatively simple and highly energy efficient electronics and without the use of linear amplifiers in particular.
- 15 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 129431-129442
Open AccessMulti-Resonant Frequency Shift Keying: A Novel and Efficient Modulation Scheme for Magnetic Communication
Magnetic communication is a promising technique in harsh environments, such as seawater. To enable efficient communication, transmitting and receiving coils are conventionally operated as part of resonant circuits. However, this results in narrow bandwidths and the associated disadvantages. Thus, most digital modulation schemes cannot be used efficiently on these systems. In this contribution, a mixed hardware/software approach for efficient frequency shift keying is presented. With this energy-efficient modulation concept, the full available bandwidth of a receiver can be utilized for data transmission, while all advantages of using a resonant circuit on the transmitter side can be retained. Towards this goal, a transmitter-side resonant circuit is designed, which supports discrete switching between multiple resonant frequencies. The data symbols are mapped onto these unique resonant frequencies. This prevents the parasitic amplitude modulation associated with conventional frequency shift keying applied to narrow bandwidth circuits, resulting in maximum transmitted magnitude and minimum symbol distortion without need for any further measures. Furthermore, the frequency spacing and/or the cardinality of the symbol alphabet can be increased considerably. At the receiver side, the classical pick-up coil is replaced by a high-sensitivity broadband magnetic field sensor. Numerical results of the mixed hardware/software scheme are provided, and are verified by an experimental setup. This setup is constructed using principles from the field of power electronics and demonstrates, how this modulation concept can be implemented with relatively simple and highly energy efficient electronics and without the use of linear amplifiers in particular.