Shaobin Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Shaobin Li has a total of 47 co-authors. Here are the top co-authors by number of shared publications:
- Yongxiang Xu
Harbin Institute of Technology
26 shared publications - Jibin Zou
Harbin Institute of Technology
22 shared publications - Lijun Xiao
Harbin Institute of Technology, Harbin, China
7 shared publications - Shaoshan Jin
School of Electrical Engineering and Automation, Harbin Institute of Technology, Harbin, China
7 shared publications - Wentao Zhang
Harbin Institute of Technology
7 shared publications - Boyuan Zheng
Harbin Engineering University
4 shared publications
Latest Publications
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (9) , 12881-12892
Sensorless Control of LC-Filtered PMSM Drives Using an Easy-Tuning Full-Order Flux Observer
In LC-filtered permanent magnet synchronous motor (PMSM) drive systems, the voltage waveform at the motor terminals can be reshaped into the sinusoidal profile, thereby enhancing motor longevity. However, the introduction of the LC filter substantially increases model complexity, which necessitates an excessively high-dimensional gain matrix to guarantee observability, thereby posing considerable challenges for observer design. To address this issue, this article proposes an easy-tuning full-order flux observer (ET-FLO) for estimating the state variables and rotor position of the LC-filtered PMSM drives. By analyzing the observer error model in the frequency domain, a single-parameter tuning strategy for pole placement is derived. This strategy greatly simplifies the adjustment of the observer gain matrix, ensuring stable operation across a wide speed range. Furthermore, the adverse effect of speed estimation error on system stability has been fully investigated by constructing an error function, thereby deriving the suitable poles configuration strategy to mitigate system instability. The effectiveness of the proposed strategy has been verified through experimental results on an LC-filtered PMSM drive system.
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (9) , 12881-12892
Sensorless Control of LC-Filtered PMSM Drives Using an Easy-Tuning Full-Order Flux Observer
In LC-filtered permanent magnet synchronous motor (PMSM) drive systems, the voltage waveform at the motor terminals can be reshaped into the sinusoidal profile, thereby enhancing motor longevity. However, the introduction of the LC filter substantially increases model complexity, which necessitates an excessively high-dimensional gain matrix to guarantee observability, thereby posing considerable challenges for observer design. To address this issue, this article proposes an easy-tuning full-order flux observer (ET-FLO) for estimating the state variables and rotor position of the LC-filtered PMSM drives. By analyzing the observer error model in the frequency domain, a single-parameter tuning strategy for pole placement is derived. This strategy greatly simplifies the adjustment of the observer gain matrix, ensuring stable operation across a wide speed range. Furthermore, the adverse effect of speed estimation error on system stability has been fully investigated by constructing an error function, thereby deriving the suitable poles configuration strategy to mitigate system instability. The effectiveness of the proposed strategy has been verified through experimental results on an LC-filtered PMSM drive system.
- 13 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. PP (4) , 1
Universal Sensorless Control Scheme for Dual Three-Phase Permanent Magnet Synchronous Motor Under Single Open-Phase Fault
In conventional sensorless control methods for dual three-phase permanent magnet synchronous motors (DTP-PMSMs), single open-phase fault (SOPF) often leads to significant errors in rotor position estimation, thereby compromising the fault tolerance capability of the drive system. To overcome this limitation, this article proposes a universal sensorless control scheme suitable for both healthy and SOPF conditions in DTP-PMSMs. First, the adverse impact of SOPF on the estimated back-electromotive forces (EMFs) of αβ-subspace in conventional sensorless methods is analyzed. Building upon these findings, a deadbeat predictive control observer is designed to generate a precise compensation voltage. This voltage is injected into the z1z2-subspace, thereby effectively suppressing the back-EMF distortion at the source. Furthermore, a novel diagnosis-free universal sensorless control topology is proposed, which adopts dual-path compensation strategy, demonstrating strong universality and adaptability to manage all types of SOPF conditions. Compared with existing fault-tolerant methods, the proposed topology eliminates the need to identify the specific faulty phase, thereby simplifying the control structure and enhancing operational reliability. Consequently, the proposed universal scheme enables accurate position estimation under both healthy and faulty conditions without requiring control structure reconfiguration. Experimental results validate the effectiveness of the proposed universal sensorless control scheme.
- 13 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. PP (4) , 1
Universal Sensorless Control Scheme for Dual Three-Phase Permanent Magnet Synchronous Motor Under Single Open-Phase Fault
In conventional sensorless control methods for dual three-phase permanent magnet synchronous motors (DTP-PMSMs), single open-phase fault (SOPF) often leads to significant errors in rotor position estimation, thereby compromising the fault tolerance capability of the drive system. To overcome this limitation, this article proposes a universal sensorless control scheme suitable for both healthy and SOPF conditions in DTP-PMSMs. First, the adverse impact of SOPF on the estimated back-electromotive forces (EMFs) of αβ-subspace in conventional sensorless methods is analyzed. Building upon these findings, a deadbeat predictive control observer is designed to generate a precise compensation voltage. This voltage is injected into the z1z2-subspace, thereby effectively suppressing the back-EMF distortion at the source. Furthermore, a novel diagnosis-free universal sensorless control topology is proposed, which adopts dual-path compensation strategy, demonstrating strong universality and adaptability to manage all types of SOPF conditions. Compared with existing fault-tolerant methods, the proposed topology eliminates the need to identify the specific faulty phase, thereby simplifying the control structure and enhancing operational reliability. Consequently, the proposed universal scheme enables accurate position estimation under both healthy and faulty conditions without requiring control structure reconfiguration. Experimental results validate the effectiveness of the proposed universal sensorless control scheme.
- 29 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (6) , 8126-8133
Unbalance Compensation for Active Magnetic Bearing Rotor System Based on Phase Shift Reduced-Order Generalized Integrator
During the operation of the active magnetic bearing (AMB) system, synchronous vibrations resulting from rotor mass unbalance present a substantial challenge. To enhance the precision of levitation control and effectively reduce rotor vibration, this paper establishes a dynamic model of a magnetic levitation rotor with unbalanced mass and analyzes the primary causes of unbalanced vibration. Based on this, an unbalance compensator utilizing a phase-shifted reduced-order generalized integral (PSROGI) is designed. This compensator takes the signals from the radial X- and Y-channel displacement sensors of the rotor as inputs, significantly reducing the computational load. By detecting the orthogonal synchronous components in the sensor output signals, the compensator can simultaneously compensate for the unbalanced forces in both channels, thereby reducing rotor displacement vibration. Additionally, the introduction of a phase shift angle broadens the stability range of the algorithm. Simulation and experimental results show that the proposed strategy can effectively suppress the synchronous components in the rotor displacement signals over a wide speed range.
- 29 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (6) , 8126-8133
Unbalance Compensation for Active Magnetic Bearing Rotor System Based on Phase Shift Reduced-Order Generalized Integrator
During the operation of the active magnetic bearing (AMB) system, synchronous vibrations resulting from rotor mass unbalance present a substantial challenge. To enhance the precision of levitation control and effectively reduce rotor vibration, this paper establishes a dynamic model of a magnetic levitation rotor with unbalanced mass and analyzes the primary causes of unbalanced vibration. Based on this, an unbalance compensator utilizing a phase-shifted reduced-order generalized integral (PSROGI) is designed. This compensator takes the signals from the radial X- and Y-channel displacement sensors of the rotor as inputs, significantly reducing the computational load. By detecting the orthogonal synchronous components in the sensor output signals, the compensator can simultaneously compensate for the unbalanced forces in both channels, thereby reducing rotor displacement vibration. Additionally, the introduction of a phase shift angle broadens the stability range of the algorithm. Simulation and experimental results show that the proposed strategy can effectively suppress the synchronous components in the rotor displacement signals over a wide speed range.
- 12 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 12 (1) , 1676-1687
Enhanced Sensorless Position Estimation for Dual Three-Phase PMSM via Terminal Voltage Detection-Based High-Frequency Injection
In this article, a novel high-frequency pulsating square-wave injection (HFPSI) strategy utilizing terminal voltage is proposed for sensorless control of dual three-phase permanent magnet synchronous motors (DTP-PMSMs) has been proposed. Different from the conventional high-frequency injection (HFI) methods with carrier current sensing, the proposed strategy utilizes the voltage induced by mutual inductance between two sets of windings as a carrier for positional information. Compared to traditional methods, the proposed approach effectively enhances the high-frequency (HF) components containing rotor position information, which facilitates the extraction and demodulation of HF voltage, thereby significantly improving sensorless control performance. At the same time, the acoustic noise can be attenuated by reducing the amplitude of the injection voltage. Besides, a switching strategy for this method has been presented in conjunction with a high-speed sensorless approach to ensure that the DTP-PMSM can achieve sensorless control across the entire speed range. This approach mitigates the influence of the sampling noise, thereby enhancing position accuracy. Finally, the validity of the proposed HFPSI strategy is experimentally confirmed.
- 12 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 12 (1) , 1676-1687
Enhanced Sensorless Position Estimation for Dual Three-Phase PMSM via Terminal Voltage Detection-Based High-Frequency Injection
In this article, a novel high-frequency pulsating square-wave injection (HFPSI) strategy utilizing terminal voltage is proposed for sensorless control of dual three-phase permanent magnet synchronous motors (DTP-PMSMs) has been proposed. Different from the conventional high-frequency injection (HFI) methods with carrier current sensing, the proposed strategy utilizes the voltage induced by mutual inductance between two sets of windings as a carrier for positional information. Compared to traditional methods, the proposed approach effectively enhances the high-frequency (HF) components containing rotor position information, which facilitates the extraction and demodulation of HF voltage, thereby significantly improving sensorless control performance. At the same time, the acoustic noise can be attenuated by reducing the amplitude of the injection voltage. Besides, a switching strategy for this method has been presented in conjunction with a high-speed sensorless approach to ensure that the DTP-PMSM can achieve sensorless control across the entire speed range. This approach mitigates the influence of the sampling noise, thereby enhancing position accuracy. Finally, the validity of the proposed HFPSI strategy is experimentally confirmed.
- 28 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 12 (1) , 1235-1244
Low-Complexity Finite Position Set-Phase Locked Loop Based on Inverse Function Construction for Sensorless Control of Dual Three-Phase PMSM
Finite position set-phase locked loop (FPS-PLL) has been extensively studied by scholars in recent years as a sensorless technology due to its advantages of parameterless tuning and excellent dynamic performance. However, compared to bandwidth-based quadrature phase locked loop (PLL), such methods impose a higher computational burden on microprocessors. To tackle this issue, this article proposes a low-complexity FPS-PLL applied to sensorless control of dual three-phase permanent magnet synchronous motors (DTP-PMSMs). The proposed FPS-PLL strategy divides all positions into 12 sectors by judging the polarity of back-electromotive forces electromotive forces (EMFs), ensuring initial approximation errors remain within $\pi $ /12. Furthermore, it introduces a normalization-free iterative strategy that achieves a theoretical accuracy of 6.96e−9 rad in merely two iterations. The convergence analysis and theoretical calculation accuracy are given. The entire computation process avoids employing complex operations such as square root and arctangent functions, thereby further improving computational efficiency. Finally, experiments are carried out on the DTP-PMSM driver platform to verify the superiority of the proposed FPS-PLL.
- 28 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 12 (1) , 1235-1244
Low-Complexity Finite Position Set-Phase Locked Loop Based on Inverse Function Construction for Sensorless Control of Dual Three-Phase PMSM
Finite position set-phase locked loop (FPS-PLL) has been extensively studied by scholars in recent years as a sensorless technology due to its advantages of parameterless tuning and excellent dynamic performance. However, compared to bandwidth-based quadrature phase locked loop (PLL), such methods impose a higher computational burden on microprocessors. To tackle this issue, this article proposes a low-complexity FPS-PLL applied to sensorless control of dual three-phase permanent magnet synchronous motors (DTP-PMSMs). The proposed FPS-PLL strategy divides all positions into 12 sectors by judging the polarity of back-electromotive forces electromotive forces (EMFs), ensuring initial approximation errors remain within $\pi $ /12. Furthermore, it introduces a normalization-free iterative strategy that achieves a theoretical accuracy of 6.96e−9 rad in merely two iterations. The convergence analysis and theoretical calculation accuracy are given. The entire computation process avoids employing complex operations such as square root and arctangent functions, thereby further improving computational efficiency. Finally, experiments are carried out on the DTP-PMSM driver platform to verify the superiority of the proposed FPS-PLL.
- 27 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 14 (3) , 3353-3365
Sensorless Fault-Tolerant Control for DTP-SynRM Under Open-Circuit Fault via Hybrid SOGI–FLL-Based Flux Observer
This paper proposes a sensorless fault-tolerant control method for a dual three-phase synchronous reluctance motor (DTP-SynRM) utilizing a hybrid flux observer with second-order generalized integrator-frequency locked loop (SOGI-FLL) under single-phase open-circuit fault. The effects of single-phase open-circuit fault on the current constraint, voltage constraint, and sensorless control are thoroughly analyzed. The analysis results indicate that open-circuit fault causes voltage signal transmission errors, which in turn lead to torque ripple and introduce harmonics into the observed flux. To suppress the torque ripple of the DTP-SynRM and enhance the accuracy of sensorless control, a compensation method is employed to eliminate the voltage signal transmission errors caused by open-circuit faults. Additionally, an adaptive filter based on the SOGI-FLL is constructed to filter out the harmonics in the observed flux. An experimental platform was built to validate the proposed method, and the results demonstrate its effectiveness and feasibility.
- 27 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 14 (3) , 3353-3365
Sensorless Fault-Tolerant Control for DTP-SynRM Under Open-Circuit Fault via Hybrid SOGI–FLL-Based Flux Observer
This paper proposes a sensorless fault-tolerant control method for a dual three-phase synchronous reluctance motor (DTP-SynRM) utilizing a hybrid flux observer with second-order generalized integrator-frequency locked loop (SOGI-FLL) under single-phase open-circuit fault. The effects of single-phase open-circuit fault on the current constraint, voltage constraint, and sensorless control are thoroughly analyzed. The analysis results indicate that open-circuit fault causes voltage signal transmission errors, which in turn lead to torque ripple and introduce harmonics into the observed flux. To suppress the torque ripple of the DTP-SynRM and enhance the accuracy of sensorless control, a compensation method is employed to eliminate the voltage signal transmission errors caused by open-circuit faults. Additionally, an adaptive filter based on the SOGI-FLL is constructed to filter out the harmonics in the observed flux. An experimental platform was built to validate the proposed method, and the results demonstrate its effectiveness and feasibility.
- 18 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. PP (1530437X) , 1
Harmonic Current Suppression of AMB Rotor System Based on Improved Multiple SOGI-FLL
In active magnetic bearing (AMB) systems, harmonic currents induced by mass unbalance and sensor runout cause the system to generate harmonic vibrations. Conventional harmonic current suppression methods depend highly on accurate rotational speed information, which limits their application in scenarios without rotational speed sensors. To address this problem, this paper first analyses the main sources of harmonic vibration and then proposes an improved multiple second-order generalized integral frequency-locked loop (IMSOGI-FLL) algorithm. The algorithm achieves adaptive estimation of the rotational frequency by utilizing the frequency of the fundamental component in the disturbance signal and effectively suppresses the harmonic currents generated by the mass unbalance and sensor beating. In addition, in order to ensure the stability of the system in the operating range, this paper designs a simple phase compensator without parameter switching, which can improve the stability range of the system in the low-frequency band. The experimental results show that the proposed algorithm can not only accurately estimate the rotational frequency but also significantly eliminate the harmonic currents caused by mass unbalance and sensor runout, which provides an effective solution for harmonic current suppression in the case of no speed sensor.
- 18 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. PP (1530437X) , 1
Harmonic Current Suppression of AMB Rotor System Based on Improved Multiple SOGI-FLL
In active magnetic bearing (AMB) systems, harmonic currents induced by mass unbalance and sensor runout cause the system to generate harmonic vibrations. Conventional harmonic current suppression methods depend highly on accurate rotational speed information, which limits their application in scenarios without rotational speed sensors. To address this problem, this paper first analyses the main sources of harmonic vibration and then proposes an improved multiple second-order generalized integral frequency-locked loop (IMSOGI-FLL) algorithm. The algorithm achieves adaptive estimation of the rotational frequency by utilizing the frequency of the fundamental component in the disturbance signal and effectively suppresses the harmonic currents generated by the mass unbalance and sensor beating. In addition, in order to ensure the stability of the system in the operating range, this paper designs a simple phase compensator without parameter switching, which can improve the stability range of the system in the low-frequency band. The experimental results show that the proposed algorithm can not only accurately estimate the rotational frequency but also significantly eliminate the harmonic currents caused by mass unbalance and sensor runout, which provides an effective solution for harmonic current suppression in the case of no speed sensor.