RPRobin Pham
Robin Pham
*This is an algorithmically generated author record based on publicly available information.
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Robin Pham has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Chung-Lung Chen
Department of Mechanical and Aerospace Engineering, University of Missouri , Columbia, Missouri 65211, USA
4 shared publications Sheng Wang
Department of Mechanical & Aerospace Engineering, University of Missouri-Columbia, Columbia, MO 65211, USA
2 shared publicationsHeng-Chieh Chien
Electronic and Optoelectronic System Research Laboratories, Industrial Technology Research Institute, Hsinchu 310401, Taiwan
1 shared publicationJack Dahlgren
1 shared publicationKai-Hao Cheng
1 shared publication- Nathaniel Grindstaff1 shared publication
Latest Publications
- 28 August 2022
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 197
Thermal-hydraulic-dynamic investigation of an inverted self-fluttering vortex generator
- 28 August 2022
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 197
Thermal-hydraulic-dynamic investigation of an inverted self-fluttering vortex generator
- 1 October 2021
- Published by AIP Publishing in Physics of Fluids
- Vol. 33 (10) , 102102
Capillary transfer: Numerical study of how topology affects the fluid flow rate into a planar microstructure with pseudopotential multiphase Lattice-Boltzmann method
We investigate how topology impacts capillary action with the hope of aiding future thermal engineering decisions. Heat pipes and their two-dimensional variant, vapor chambers are essential components in electronics cooling. With thin-film evaporation as the driving force for such high-heat-flux movers, studies have been done to optimize the thermal performance of different designs. However, the fundamental problem of liquid transportation needs to be addressed exclusively: evaporation can only work as long as the new liquid is continuously being replaced. The device achieves this by the capillary process (or wicking) through the thermal ground (or wicks): a configuration of microstructures attached to the device's walls. Some planar topologies of the structure allow for consistent but slower mass feeding; others offer higher bandwidth but with local flow hindrance, creating a pulsating tendency; certain conditions would even block the capillary flow. Surveying the capillary performance of different two-dimensional designs of the thermal ground, we encounter a topological factor that correlates with this mass transfer rate. We incorporate in the factor the wick's width, its height, and the gap between one microstructure to another. An energy model is studied to explain the underlying influence of the structure topology, while Lattice-Boltzmann method is used to evaluate the capillary dynamics inside the thermal ground. With ultra-thin applications in mind, the paper looks at the length scales of micrometers with a wick height of μm. Overall, we find that tightly packed structures pull the most liquid in the same amount of time; however, we find that two core constraints need to be met: sufficient clearance between structures and freedom of mobility.- 1 October 2021
- Published by AIP Publishing in Physics of Fluids
- Vol. 33 (10) , 102102
Capillary transfer: Numerical study of how topology affects the fluid flow rate into a planar microstructure with pseudopotential multiphase Lattice-Boltzmann method
We investigate how topology impacts capillary action with the hope of aiding future thermal engineering decisions. Heat pipes and their two-dimensional variant, vapor chambers are essential components in electronics cooling. With thin-film evaporation as the driving force for such high-heat-flux movers, studies have been done to optimize the thermal performance of different designs. However, the fundamental problem of liquid transportation needs to be addressed exclusively: evaporation can only work as long as the new liquid is continuously being replaced. The device achieves this by the capillary process (or wicking) through the thermal ground (or wicks): a configuration of microstructures attached to the device's walls. Some planar topologies of the structure allow for consistent but slower mass feeding; others offer higher bandwidth but with local flow hindrance, creating a pulsating tendency; certain conditions would even block the capillary flow. Surveying the capillary performance of different two-dimensional designs of the thermal ground, we encounter a topological factor that correlates with this mass transfer rate. We incorporate in the factor the wick's width, its height, and the gap between one microstructure to another. An energy model is studied to explain the underlying influence of the structure topology, while Lattice-Boltzmann method is used to evaluate the capillary dynamics inside the thermal ground. With ultra-thin applications in mind, the paper looks at the length scales of micrometers with a wick height of μm. Overall, we find that tightly packed structures pull the most liquid in the same amount of time; however, we find that two core constraints need to be met: sufficient clearance between structures and freedom of mobility.