Eric Nery Chaves
Eric Nery Chaves has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Ghunter Paulo Viajante
Power System Research Core (NuPSE), Federal Institute of Gois (IFG), Goinia, Gois, Brazil
2 shared publications - Luciano Coutinho Gomes
Faculty of Electrical Engineering, Federal University of Uberlandia (UFU), Uberlandia 38408-100, Brazil
2 shared publications - Marcelo Escobar de Oliveira
Federal University of Uberlndia,Electric drives laboratory (LaCE),Uberlndia,Brazil
2 shared publications - Ricardo Tirone Fidelis
Laboratory of Electrical Drives (LaCE), Federal University of Uberlndia (UFU), Uberlndia, Minas Gerais, Brazil
2 shared publications - Victor Henrique da Cunha Faria
Universidade Federal de Uberlândia
2 shared publications - Augusto Wohlgemuth Fleury Veloso da Silveira
Federal University of Uberlandia (UFU)
1 shared publication
Latest Publications
- 6 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Virtual Instrumentation and Torque Estimator for the Drive and Control of the Switched Reluctance Machine
This paper describes the development of a virtual instrumentation system that can efficiently measure and estimate electrical quantities, magnetic flux, torque, and efficiency of a Switched Reluctance Machine (SRM) in real-time. The system's low-cost DSP implementation enables its use for real-time parameter estimation, which facilitates the implementation of new control techniques. The paper presents the results of computer simulations and experimental tests using an SRM as a motor, which demonstrate the effectiveness of the system. The virtual instrumentation system's low computational cost makes it a highly viable option for applications that require real-time parameter estimation.
- 6 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Virtual Instrumentation and Torque Estimator for the Drive and Control of the Switched Reluctance Machine
This paper describes the development of a virtual instrumentation system that can efficiently measure and estimate electrical quantities, magnetic flux, torque, and efficiency of a Switched Reluctance Machine (SRM) in real-time. The system's low-cost DSP implementation enables its use for real-time parameter estimation, which facilitates the implementation of new control techniques. The paper presents the results of computer simulations and experimental tests using an SRM as a motor, which demonstrate the effectiveness of the system. The virtual instrumentation system's low computational cost makes it a highly viable option for applications that require real-time parameter estimation.
- Open Access
- 27 March 2022
- Published by Research, Society and Development in Research, Society and Development
- Vol. 11 (5)
A new inductance estimator based on Lagrange Form polynomials for real-time switched reluctance machine control
This paper presents a new methodology for modeling the inductance curves of switched-reluctance machines using cubic splines based on Lagrange form polynomials. The proposed methodology allows for the estimation of the instantaneous inductance and derivative of the inductance in each phase of the machine. All steps of the proposed methodology are presented and discussed, detailing the information necessary for its use. The results of an experimental and computational simulation, both as a motor and a generator, are presented and discussed, and the estimated curves are compared with the design curves of each result. The inductance estimator was embedded in a low-cost DSP, and the machine was driven using an experimental bench. The experimental results are presented and compared with the simulation results, allowing for the evaluation of the accuracy level obtained by the proposed estimator. The estimator combines precision with low computational cost, which makes this method a strong candidate for systems that require estimation of machine parameters in real time, such as torque and flux, permitting the implementation of new control techniques.
- 27 March 2022
- Published by Research, Society and Development in Research, Society and Development
- Vol. 11 (5)
Open AccessA new inductance estimator based on Lagrange Form polynomials for real-time switched reluctance machine control
This paper presents a new methodology for modeling the inductance curves of switched-reluctance machines using cubic splines based on Lagrange form polynomials. The proposed methodology allows for the estimation of the instantaneous inductance and derivative of the inductance in each phase of the machine. All steps of the proposed methodology are presented and discussed, detailing the information necessary for its use. The results of an experimental and computational simulation, both as a motor and a generator, are presented and discussed, and the estimated curves are compared with the design curves of each result. The inductance estimator was embedded in a low-cost DSP, and the machine was driven using an experimental bench. The experimental results are presented and compared with the simulation results, allowing for the evaluation of the accuracy level obtained by the proposed estimator. The estimator combines precision with low computational cost, which makes this method a strong candidate for systems that require estimation of machine parameters in real time, such as torque and flux, permitting the implementation of new control techniques.
- 3 October 2021
- Published by Wiley in International Journal of Numerical Modelling: Electronic Networks, Devices and Fields
- Vol. 35 (2) , e2964
Design and implementation of an internal model controller applied to MPPT PV systems using phase‐shift full‐bridge DC–DC converter
This paper presents the design of an internal model controller with one degree of freedom (1DOF‐IMC) that will be applied to a full‐bridge DC–DC converter driven by phase‐shift PWM. This DC–DC converter will be used in photovoltaic systems for maximum power point tracking (MPPT), with the objective of developing a single‐phase micro‐inverter connected to the grid integrated to the photovoltaic module. It will be presented the mathematical modeling of this converter to control the input voltage aiming the application in MPPT and the design of the respective controller. The proposal testing and validation strategy was performed by comparison with a PI compensator. Simulations and experimental results will be presented and the performance of both controllers are evaluated and discussed. Both control strategies were discretized with the sampling frequency at 20 kHz and implemented in a floating point using the Texas Instruments® DSC TMS320F28335.
- 3 October 2021
- Published by Wiley in International Journal of Numerical Modelling: Electronic Networks, Devices and Fields
- Vol. 35 (2) , e2964
Design and implementation of an internal model controller applied to MPPT PV systems using phase‐shift full‐bridge DC–DC converter
This paper presents the design of an internal model controller with one degree of freedom (1DOF‐IMC) that will be applied to a full‐bridge DC–DC converter driven by phase‐shift PWM. This DC–DC converter will be used in photovoltaic systems for maximum power point tracking (MPPT), with the objective of developing a single‐phase micro‐inverter connected to the grid integrated to the photovoltaic module. It will be presented the mathematical modeling of this converter to control the input voltage aiming the application in MPPT and the design of the respective controller. The proposal testing and validation strategy was performed by comparison with a PI compensator. Simulations and experimental results will be presented and the performance of both controllers are evaluated and discussed. Both control strategies were discretized with the sampling frequency at 20 kHz and implemented in a floating point using the Texas Instruments® DSC TMS320F28335.
- Open Access
- 30 September 2021
- Published by UK Zhende Publishing Limited Company in Renewable Energy and Power Quality Journal
- Vol. 19 (2)
Comparative Analysis of Dynamic Performance Between Switched Reluctance Motors 6x4 and 8x6
This paper presents a comparative study between the Switched Reluctance Machine (SRM) 8x6 and 6x4 operating as a motor with both 60kW of power. The computer simulation was performed in Matlab™ / Simulink® environment and allowed the machine behavior under various operating conditions to be verified. This work made it possible to evaluate: phase voltage and current, speed, torque and efficiency. Comparative results between the two machines will be presented and discussed.
- 30 September 2021
- Published by UK Zhende Publishing Limited Company in Renewable Energy and Power Quality Journal
- Vol. 19 (2)
Open AccessComparative Analysis of Dynamic Performance Between Switched Reluctance Motors 6x4 and 8x6
This paper presents a comparative study between the Switched Reluctance Machine (SRM) 8x6 and 6x4 operating as a motor with both 60kW of power. The computer simulation was performed in Matlab™ / Simulink® environment and allowed the machine behavior under various operating conditions to be verified. This work made it possible to evaluate: phase voltage and current, speed, torque and efficiency. Comparative results between the two machines will be presented and discussed.