WNW. Morgan NeSmith

W. Morgan NeSmith

*This is an algorithmically generated author record based on publicly available information.

W. Morgan NeSmith has a total of 2 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Shortcomings of the Davisson Offset Limit Applied to Axial Compressive Load Tests on Cast-in-Place Piles

    by W. Morgan NeSmith, Timothy C. Siegel

    Since its introduction in 1973, the Davisson Offset Limit has been widely used in the United States for interpretation of axial compressive load tests on pile foundations and is one of three methods explicitly accepted by the 2006 International Building Code. An examination of the fundamental assumptions of the DOL shows that its application to cast-in-place piles lacks scientific basis and leads to over conservatism. Interestingly, these are the same reasons given by Davisson for its development. The results of the examination indicate that there are notable fallacies in the Davisson Offset Limit, including the assumptions that: (1) the cast-in-place pile behaves as a "fixed-base, free-standing column.", (2) an elastic line is a dependable reference line for interpretation of load tests on cast-in-place piles, and; (3) an offset of 3.8 mm + D (inches)/120 from the elastic line represents the movement necessary to mobilize toe resistance of cast-in-place piles. Considering these results, the authors present suggestions ranging from modifications to the Davison Offset Limit that recognizes the greater movement required to mobilize the toe resistance to codification of a more rational criterion better suited to interpret the axial compressive capacity of cast-in-place piles.


  • Advancements in Data Acquisition-Based Design for Drilled Displacement Piles

    by W. Morgan NeSmith

    The authors described the equipment and processes involved in the measurement of the effort expended by the drilling platform in the installation of Drilled Displacement (DD) piles (called Installation Effort or IE) in a paper presented at the 2006 ASCE GeoCongress (NeSmith and NeSmith, 2006a). The use of IE as an indicator of stratigraphy and DD pile capacity was addressed in a companion paper (NeSmith and NeSmith, 2006b). Recent advances in this area include improvements in the acquisition of data required to calculate IE; enhancements in the real time presentation of IE data during pile installation; modifications to the calculation of IE and Cumulative IE; and refinements in the relationship between Cumulative IE and pile capacity. These developments have facilitated the application of IE as a practical tool for DD pile design and for quality control of DD pile installation. The advances mentioned above are discussed herein and include comments on site characterization, an overview of design methodology, recommendations for test pile programs, and use of the database of Installation Effort vs. Capacity collected by the authors.


  • Practical Considerations for Design and Installation of Drilled Displacement Piles

    by W. Morgan NeSmith, J. Fox

    A design methodology for the capacity of Drilled Displacement (DD) piles was presented at the International Deep Foundation Congress in 2002. Advances in final design / installation developed since then were incorporated into a DD pile program for two large hotels in Orange County, Florida. The site consisted of granular soils to about 15-m (50-ft) depth underlain by inter-bedded coarse and fine-grained soils. The original design called for 457-mm (18-in) diameter by 29.3-m (96-ft) long conventional auger cast piles. It was estimated that 457-mm (18-in) DD piles installed in the granular materials within the upper 15 m (50 ft) would more efficiently support the proposed loads. The project team elected to utilize DD piles at a substantial cost savings. This paper focuses on one of the two hotel areas. The conditions and construction methods are applicable to both hotel sites.

  • Application of Data Acquired during Drilled Displacement Pile Installation

    by W. Morgan NeSmith

    The gathering of information relative to the casting process has long been the major thrust of quality control for cast-in-place pile evaluation, and there have been significant advances that enhance the quality of data obtained during casting. Additionally, systems are now available that provide the capability to electronically gather information such as applied torque, crowd, and tool rotation and penetration rates in a form which also allows for a quantitative examination of the drilling process. In general, this aspect of installation has been heretofore evaluated only subjectively in the United States, if at all. New processes for drilled displacement pile design and verification are emerging as a result of the quantity and quality of data that can now be made available. This paper describes how the collected and processed installation data can be used as an adjunct to Geotechnical site characterization and as a verification tool with respect to pile capacity. The analytical development of the methodology for processing the acquired data is discussed and application is illustrated through examples using specific project information from a variety of geologic settings.