Michael Naus
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Michael Naus has a total of 123 co-authors. Here are the top co-authors by number of shared publications:
- Ian Pong
Lawrence Berkeley National Laboratory
7 shared publications - Soren Prestemon
Lawrence Berkeley National Laboratory
5 shared publications - Andy Lin
Lawrence Berkeley National Laboratory
4 shared publications - GianLuca Sabbi
Lawrence Berkeley National Laboratory
4 shared publications - Jean-Francois Croteau
Lawrence Berkeley National Laboratory
4 shared publications - Paolo Ferracin
Lawrence Berkeley National Laboratory, Berkeley, CA, USA
3 shared publications
Latest Publications
- Open Access
- 14 August 2026
- Published by American Physical Society (APS) in Physical Review Accelerators and Beams
- Vol. 29 (8)
Fabrication and test of a 6-tesla-class high-temperature superconducting dipole magnet at 4.2 K
Superconducting magnets enable energy-frontier accelerators by generating strong magnetic fields to steer and focus the particles. Although high-temperature superconductors such as REBa 2 Cu 3 O x (, RE = rare earth) hold a strong potential for generating a higher magnetic field than Nb-Ti and Nb 3 Sn , the associated magnet and conductor technology for accelerator applications is still in its infancy. The U.S. Magnet Development Program is developing magnet technology in collaboration with industry. Here we report an experiment of making a dipole magnet called C3 using commercial high-temperature superconducting wires. The magnet, following a canted cos θ design, generated a dipole field of 5.99 T at 4.2 K in its clear aperture of 65 mm at 6.795 kA when a resistive voltage of 105 μ V appeared across one of the coils in the magnet. The stored energy was 53 kJ at the peak field. The magnet showed no degradation in the current-carrying capability at 4.2 K after the thermal cycle. We report on the detailed design, fabrication, and performance of the C3 magnet that can be of interest to potential users of this emerging technology. We also discuss issues and research needs to inform future magnet development. The experiment represented another step to addressing if the high-temperature superconducting accelerator magnet technology can increase the discovery capability of future particle accelerators.
- 14 August 2026
- Published by American Physical Society (APS) in Physical Review Accelerators and Beams
- Vol. 29 (8)
Open AccessFabrication and test of a 6-tesla-class high-temperature superconducting dipole magnet at 4.2 K
Superconducting magnets enable energy-frontier accelerators by generating strong magnetic fields to steer and focus the particles. Although high-temperature superconductors such as REBa 2 Cu 3 O x (, RE = rare earth) hold a strong potential for generating a higher magnetic field than Nb-Ti and Nb 3 Sn , the associated magnet and conductor technology for accelerator applications is still in its infancy. The U.S. Magnet Development Program is developing magnet technology in collaboration with industry. Here we report an experiment of making a dipole magnet called C3 using commercial high-temperature superconducting wires. The magnet, following a canted cos θ design, generated a dipole field of 5.99 T at 4.2 K in its clear aperture of 65 mm at 6.795 kA when a resistive voltage of 105 μ V appeared across one of the coils in the magnet. The stored energy was 53 kJ at the peak field. The magnet showed no degradation in the current-carrying capability at 4.2 K after the thermal cycle. We report on the detailed design, fabrication, and performance of the C3 magnet that can be of interest to potential users of this emerging technology. We also discuss issues and research needs to inform future magnet development. The experiment represented another step to addressing if the high-temperature superconducting accelerator magnet technology can increase the discovery capability of future particle accelerators.
- 30 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Twisting & Bending Performance of a Subscale CORC Cable-in-Conduit-Conductor for Fusion and Detector Magnet Applications
Future magnetic confinement fusion machines and detector magnets will likely utilize high temperature superconducting (HTS) wire and/or tapes, configured in a Cable-in-Conduit-Conductor (CICC) to generate magnetic fields at temperatures above 4.2 K. As such, these CICCs will need to be twisted & bent to meet the design criteria for any given machine. We investigated the critical current (Ic) degradation of a subscale 6-around-1 CICC using Conductor-on-Round-Core® (CORC®) wires after ever increasing deformation. A CORC® wire was inserted into one of six outer openings of an extruded aluminum conduit to form a sub-scale CICC, after which the CICC was twisted to ∼25 cm pitch and the whole assembly was then sequentially bent to nominal radii of ∼50 cm, ∼35 cm, and ∼25 cm. The Ic values at 77 K and self-field when straight and after each deformation step was measured. The CORC® wire Ic was robust to this type of “twisting + bending” deformation, with an overall degradation of ∼10% with respect to the straight, non-twisted wire. We also describe a CICC twisting process that potentially allows twisting of continuous-length CICCs after the CORC® wires are inserted. This method can lead to a scalable fabrication process of long-length CORC® CICCs that are required for manufacture of high-field fusion magnets and detector magnets for high-energy physics research.
- 30 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-5
Twisting & Bending Performance of a Subscale CORC Cable-in-Conduit-Conductor for Fusion and Detector Magnet Applications
Future magnetic confinement fusion machines and detector magnets will likely utilize high temperature superconducting (HTS) wire and/or tapes, configured in a Cable-in-Conduit-Conductor (CICC) to generate magnetic fields at temperatures above 4.2 K. As such, these CICCs will need to be twisted & bent to meet the design criteria for any given machine. We investigated the critical current (Ic) degradation of a subscale 6-around-1 CICC using Conductor-on-Round-Core® (CORC®) wires after ever increasing deformation. A CORC® wire was inserted into one of six outer openings of an extruded aluminum conduit to form a sub-scale CICC, after which the CICC was twisted to ∼25 cm pitch and the whole assembly was then sequentially bent to nominal radii of ∼50 cm, ∼35 cm, and ∼25 cm. The Ic values at 77 K and self-field when straight and after each deformation step was measured. The CORC® wire Ic was robust to this type of “twisting + bending” deformation, with an overall degradation of ∼10% with respect to the straight, non-twisted wire. We also describe a CICC twisting process that potentially allows twisting of continuous-length CICCs after the CORC® wires are inserted. This method can lead to a scalable fabrication process of long-length CORC® CICCs that are required for manufacture of high-field fusion magnets and detector magnets for high-energy physics research.
- 26 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Design and Development of a 28 GHz Nb$_{{\text{3}}}$Sn ECR Ion Source Superconducting Magnet
Worldwide several electron cyclotron resonance (ECR) ion sources have been developed and in operation for heavy ion accelerators using Nb-Ti superconducting magnets. The Versatile ECR ion source for NUclear Science (VENUS) at the Lawrence Berkeley National Lab (LBNL) and the newly commissioned 28 GHz superconducting ECR ion source at the Facility for Rare Isotope Beams (FRIB) were developed by LBNL. Both sources adopt a scheme with a sextupole magnet inside a mirror-type solenoid to confine the ions and electrons. Nb-Ti coils limit all the existing ECR ion sources to operate below $\sim$ 9 T at 4.2 K. Nb $_{{\text{3}}}$ Sn potentially enables next generation ECR ion sources with a higher field limit ( $\sim$ 22 T at 4.2 K). As an example, a 45 GHz ECR ion source Nb $_{{\text{3}}}$ Sn magnet is currently being developed by the Institute of Modern Physics (IMP) in China. Clearly conductor characteristics of Nb $_{{\text{3}}}$ Sn are very much different and new development are needed to meet challenges such as coil fabrication. FRIB and LBNL team up again to develop ECR ion sources based on Nb $_{{\text{3}}}$ Sn. Here as the first step, this paper describes the design of a second 28 GHz superconducting ECR ion source using Nb $_{{\text{3}}}$ Sn coils at FRIB. We present conductor selection and characteristics, magnetic design, mechanical design and cold mass assembly, coil fabrication challenges and potential solution, quench protection, and the development and prototyping efforts so far.
- 26 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Design and Development of a 28 GHz Nb$_{{\text{3}}}$Sn ECR Ion Source Superconducting Magnet
Worldwide several electron cyclotron resonance (ECR) ion sources have been developed and in operation for heavy ion accelerators using Nb-Ti superconducting magnets. The Versatile ECR ion source for NUclear Science (VENUS) at the Lawrence Berkeley National Lab (LBNL) and the newly commissioned 28 GHz superconducting ECR ion source at the Facility for Rare Isotope Beams (FRIB) were developed by LBNL. Both sources adopt a scheme with a sextupole magnet inside a mirror-type solenoid to confine the ions and electrons. Nb-Ti coils limit all the existing ECR ion sources to operate below $\sim$ 9 T at 4.2 K. Nb $_{{\text{3}}}$ Sn potentially enables next generation ECR ion sources with a higher field limit ( $\sim$ 22 T at 4.2 K). As an example, a 45 GHz ECR ion source Nb $_{{\text{3}}}$ Sn magnet is currently being developed by the Institute of Modern Physics (IMP) in China. Clearly conductor characteristics of Nb $_{{\text{3}}}$ Sn are very much different and new development are needed to meet challenges such as coil fabrication. FRIB and LBNL team up again to develop ECR ion sources based on Nb $_{{\text{3}}}$ Sn. Here as the first step, this paper describes the design of a second 28 GHz superconducting ECR ion source using Nb $_{{\text{3}}}$ Sn coils at FRIB. We present conductor selection and characteristics, magnetic design, mechanical design and cold mass assembly, coil fabrication challenges and potential solution, quench protection, and the development and prototyping efforts so far.
- 18 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Microstructure Characterization of Nb3Sn Wires With Nanoprecipitate Artificial Pinning Centers Using Synchrotron High-Energy X-Rays
Synchrotron high-energy X-rays were used in an attempt to estimate nanoprecipitate size and size distribution in Nb 3 Sn powder-in-tube wires with ZrO 2 or HfO 2 artificial pinning centers via small angle X-ray scattering (SAXS). The effect of sample preparation was studied but measurements for as-received and for partially etched wires were not successful. Extracted sub-elements appeared to show more scattering contrast due to the lower number of phases, but no particle size could be extracted in this first attempt. Analysis of TEM data from the literature showed large particle size distribution (PSD) for different heat treatment conditions, suggesting that PSD could likely never be measured with SAXS due to a smeared signal. Experimental challenges with in-situ measurements revealed the sensitivity of infra-red furnaces and to changes in sample emissivity. The use of in-situ wide angle X-ray scattering data was successful in estimating the wire temperatures from the lattice parameter of copper and could be used in future heat treatment studies to better understand tin oxide dissolution.
- 18 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 34 (5) , 1-5
Microstructure Characterization of Nb3Sn Wires With Nanoprecipitate Artificial Pinning Centers Using Synchrotron High-Energy X-Rays
Synchrotron high-energy X-rays were used in an attempt to estimate nanoprecipitate size and size distribution in Nb 3 Sn powder-in-tube wires with ZrO 2 or HfO 2 artificial pinning centers via small angle X-ray scattering (SAXS). The effect of sample preparation was studied but measurements for as-received and for partially etched wires were not successful. Extracted sub-elements appeared to show more scattering contrast due to the lower number of phases, but no particle size could be extracted in this first attempt. Analysis of TEM data from the literature showed large particle size distribution (PSD) for different heat treatment conditions, suggesting that PSD could likely never be measured with SAXS due to a smeared signal. Experimental challenges with in-situ measurements revealed the sensitivity of infra-red furnaces and to changes in sample emissivity. The use of in-situ wide angle X-ray scattering data was successful in estimating the wire temperatures from the lattice parameter of copper and could be used in future heat treatment studies to better understand tin oxide dissolution.
- 12 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-5
RRP Nb3Sn Subelement Shear Dependence on Hexagonal Subelement Stack Orientation and the Strand's Position Within a Rutherford Cable
Superconducting strands built into Rutherford cables undergo high deformation at the cable edges. This deformation negatively impacts subelement integrity and subsequently the Residual Resistance Ratio (RRR) of the stabilization Cu in Nb 3 Sn strands after heat treatment due to compromised diffusion barriers [1]. Rutherford cables for the high luminosity upgrade of the LHC at CERN (HL-LHC) use Restack Rod Process (RRP) Nb 3 Sn wires with a 108/127 subelement stack. Numerous transverse cross-sectional samples from the cables made under the HL-LHC Accelerator Upgrade Project (“HL-LHC AUP”) [2] have been mounted, polished, and analyzed with light microscopy. The number of sheared subelements within a strand was seen to depend not only on a strand's position in the overall cable (i.e. center vs. edge), but also on its specific position within the cable edge. Moreover, the rotational angle of the subelement stack within a strand, relative to the cable's centerline plane, appears to play a role. There is a need to understand these dependencies, as they might impact the applicability of any criterion for a maximum number of sheared subelements (typically < 15% of subelements) applied to series production quality assurance, often imposed to ensure acceptable RRR degradation. By gathering data across many HL-LHC AUP cables and utilizing a more statistical approach, we aim to establish more accurate success criteria for future R&D cables using RRP wire when the available cable runs (and thus samples) are limited.
- 12 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-5
RRP Nb3Sn Subelement Shear Dependence on Hexagonal Subelement Stack Orientation and the Strand's Position Within a Rutherford Cable
Superconducting strands built into Rutherford cables undergo high deformation at the cable edges. This deformation negatively impacts subelement integrity and subsequently the Residual Resistance Ratio (RRR) of the stabilization Cu in Nb 3 Sn strands after heat treatment due to compromised diffusion barriers [1]. Rutherford cables for the high luminosity upgrade of the LHC at CERN (HL-LHC) use Restack Rod Process (RRP) Nb 3 Sn wires with a 108/127 subelement stack. Numerous transverse cross-sectional samples from the cables made under the HL-LHC Accelerator Upgrade Project (“HL-LHC AUP”) [2] have been mounted, polished, and analyzed with light microscopy. The number of sheared subelements within a strand was seen to depend not only on a strand's position in the overall cable (i.e. center vs. edge), but also on its specific position within the cable edge. Moreover, the rotational angle of the subelement stack within a strand, relative to the cable's centerline plane, appears to play a role. There is a need to understand these dependencies, as they might impact the applicability of any criterion for a maximum number of sheared subelements (typically < 15% of subelements) applied to series production quality assurance, often imposed to ensure acceptable RRR degradation. By gathering data across many HL-LHC AUP cables and utilizing a more statistical approach, we aim to establish more accurate success criteria for future R&D cables using RRP wire when the available cable runs (and thus samples) are limited.
- 31 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-8
Challenges and Lessons Learned From Fabrication, Testing, and Analysis of Eight MQXFA Low Beta Quadrupole Magnets for HL-LHC
By the end of October 2022, the US HL-LHC Accelerator Upgrade Project (AUP) had completed fabrication of ten MQXFA magnets and tested eight of them. The MQXFA magnets are the low-beta quadrupole magnets to be used in the Q1 and Q3 Inner Triplet elements of the High Luminosity LHC. This AUP effort is shared by BNL, Fermilab, and LBNL, with strand verification tests at NHMFL. An important step of the AUP QA plan is the testing of MQXFA magnets in a vertical cryostat at BNL. The acceptance criteria that could be tested at BNL were all met by the first four production magnets (MQXFA03-MQXFA06). Subsequently, two magnets (MQXFA07 and MQXFA08) did not meet some of the criteria and were disassembled. Lessons learned during the disassembly of MQXFA07 caused a revision to the assembly specifications that were used for MQXFA10 and subsequent magnets. In this article, we present a summary of: 1) the fabrication and test data for all the MQXFA magnets; 2) the analysis of MQXFA07/A08 test results with characterization of the limiting mechanism; 3) the outcome of the investigation, including the lessons learned during MQXFA07 disassembly; and 4) the finite element analysis correlating observations with test performance.
- 31 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-8
Challenges and Lessons Learned From Fabrication, Testing, and Analysis of Eight MQXFA Low Beta Quadrupole Magnets for HL-LHC
By the end of October 2022, the US HL-LHC Accelerator Upgrade Project (AUP) had completed fabrication of ten MQXFA magnets and tested eight of them. The MQXFA magnets are the low-beta quadrupole magnets to be used in the Q1 and Q3 Inner Triplet elements of the High Luminosity LHC. This AUP effort is shared by BNL, Fermilab, and LBNL, with strand verification tests at NHMFL. An important step of the AUP QA plan is the testing of MQXFA magnets in a vertical cryostat at BNL. The acceptance criteria that could be tested at BNL were all met by the first four production magnets (MQXFA03-MQXFA06). Subsequently, two magnets (MQXFA07 and MQXFA08) did not meet some of the criteria and were disassembled. Lessons learned during the disassembly of MQXFA07 caused a revision to the assembly specifications that were used for MQXFA10 and subsequent magnets. In this article, we present a summary of: 1) the fabrication and test data for all the MQXFA magnets; 2) the analysis of MQXFA07/A08 test results with characterization of the limiting mechanism; 3) the outcome of the investigation, including the lessons learned during MQXFA07 disassembly; and 4) the finite element analysis correlating observations with test performance.
- Open Access
MQXFA Final Design Report
The MQXFA Quadrupole magnets will be installed in High Luminosity LHC to form the Q1 and Q3 inner triplet optical elements in front of the interaction points 1 (ATLAS) and 5 (CMS). A pair of MQXFA units is assembled in a stainless steel helium vessel, including the end domes, to make the Q1 Cold Mass or the Q3 Cold Mass. The US HL LHC Accelerator Upgrade Project* is responsible for the design, manufacturing and test of the Q1/Q3 Cold Masses and the complete MQXFA magnets. CERN provides the cryostat components and is responsible for integration and installation in HL LHC. The MQXFA quadrupoles have 150 mm aperture, 4.2 m magnetic length, nominal gradient of 132.2 T/m, and coil peak field of 11.3 T. They use Nb_3Sn conductor and a support structure made of segmented aluminum shells pre-loaded by using bladders and keys. This report presents the final design of the MQXFA quadrupole magnets. *Supported by the U.S. Department of Energy, Office of Science, Office of High Energy Physics
Open AccessMQXFA Final Design Report
The MQXFA Quadrupole magnets will be installed in High Luminosity LHC to form the Q1 and Q3 inner triplet optical elements in front of the interaction points 1 (ATLAS) and 5 (CMS). A pair of MQXFA units is assembled in a stainless steel helium vessel, including the end domes, to make the Q1 Cold Mass or the Q3 Cold Mass. The US HL LHC Accelerator Upgrade Project* is responsible for the design, manufacturing and test of the Q1/Q3 Cold Masses and the complete MQXFA magnets. CERN provides the cryostat components and is responsible for integration and installation in HL LHC. The MQXFA quadrupoles have 150 mm aperture, 4.2 m magnetic length, nominal gradient of 132.2 T/m, and coil peak field of 11.3 T. They use Nb_3Sn conductor and a support structure made of segmented aluminum shells pre-loaded by using bladders and keys. This report presents the final design of the MQXFA quadrupole magnets. *Supported by the U.S. Department of Energy, Office of Science, Office of High Energy Physics
- 12 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 31 (7) , 1-5
Cable Design and Development for the High-Temperature Superconductor Cable Test Facility Magnet
A large bore “High-Temperature Superconductor Cable Test Facility Magnet” for testing advanced cables and inserts in high transverse field is in its design phase. This magnet will be the core component of a facility for developing conductors and accelerator magnets operating above 15 T, an enabling technology for next-generation fusion devices using magnetic confinement of plasma and for future energy frontier colliders. The procurement of Nb 3 Sn conductor, fabrication of cables, winding of coils, and assembly of the dipole magnet will be done at Lawrence Berkeley National Laboratory (LBNL) and the test pit and cryostat will be constructed at Fermi National Accelerator Laboratory. This article will present the conductor element of the LBNL project, specifically cable design parameters (based on the Bruker OST RRP $^{\bigcirc \!\!\!\! {\hbox{R}}}$ Nb 3 Sn superconducting wire) and the development phase cable fabrication experience. Challenges of the cable fabrication will be discussed. The wire and cable planned for this magnet are similar to those under study for the Future Circular Collider and other large facility magnets. The successful fabrication of the development cable has positive implications for these other projects.
- 12 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 31 (7) , 1-5
Cable Design and Development for the High-Temperature Superconductor Cable Test Facility Magnet
A large bore “High-Temperature Superconductor Cable Test Facility Magnet” for testing advanced cables and inserts in high transverse field is in its design phase. This magnet will be the core component of a facility for developing conductors and accelerator magnets operating above 15 T, an enabling technology for next-generation fusion devices using magnetic confinement of plasma and for future energy frontier colliders. The procurement of Nb 3 Sn conductor, fabrication of cables, winding of coils, and assembly of the dipole magnet will be done at Lawrence Berkeley National Laboratory (LBNL) and the test pit and cryostat will be constructed at Fermi National Accelerator Laboratory. This article will present the conductor element of the LBNL project, specifically cable design parameters (based on the Bruker OST RRP $^{\bigcirc \!\!\!\! {\hbox{R}}}$ Nb 3 Sn superconducting wire) and the development phase cable fabrication experience. Challenges of the cable fabrication will be discussed. The wire and cable planned for this magnet are similar to those under study for the Future Circular Collider and other large facility magnets. The successful fabrication of the development cable has positive implications for these other projects.