A. Arun Negemiya
A. Arun Negemiya has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Selvarajan Rajakumar
Department of Manufacturing Engineering, Centre for Materials Joining and Research (CEMAJOR), Annamalai University, Annamalai Nagar, India
5 shared publications - Tushar Sonar
Department of Welding Equipment and Technology, Institution of Engineering and Technology, South Ural State University (National Research University), Chelyabinsk, Russia
4 shared publications - Mikhail Ivanov
South Ural State University
2 shared publications - A. N. Shankar
Department of HSE & Civil Engineering
1 shared publication - Areda Batu
Department of Chemical Engineering
1 shared publication B. Prakash
Department of Mechanical Engineering
1 shared publication
Latest Publications
- Open Access
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Journal of Aerospace Technology and Management
- Vol. 18
Improving Airport Safety and Operational Efficiency through an Integrated Comprehensive Foreign Object Debris Management System
The airbase foreign object debris (FOD) management system is designed to deliver a comprehensive, technology-driven solution that improves airport maintenance, operational efficiency, and overall safety. Its primary objective is to address challenges posed by FOD in critical areas such as runways, taxiways, aprons, and other operational zones. The proposed system integrates advanced sensor technologies, data analytics, and automation to enable accurate detection, identification, and timely reporting of debris. Continuous real-time monitoring of the airfield environment allows early identification of potential hazards, significantly reducing risks and operational disruptions caused by FOD incidents. Automation within the system enhances response coordination by ensuring swift and appropriate corrective actions are taken once debris is detected, thereby minimizing safety threats and delays. In addition, the study employs a dual strengths, weaknesses, opportunities, and threats framework, combined with a comparative regulatory analysis of guidelines issued by the Federal Aviation Administration, the European Union Aviation Safety Agency, and the National Civil Aviation Agency. This integrated approach supports informed decision-making for electric vertical takeoff and landing aircraft integration and vertiport deployment within Urban Air Mobility ecosystems.
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Journal of Aerospace Technology and Management
- Vol. 18
Open AccessImproving Airport Safety and Operational Efficiency through an Integrated Comprehensive Foreign Object Debris Management System
The airbase foreign object debris (FOD) management system is designed to deliver a comprehensive, technology-driven solution that improves airport maintenance, operational efficiency, and overall safety. Its primary objective is to address challenges posed by FOD in critical areas such as runways, taxiways, aprons, and other operational zones. The proposed system integrates advanced sensor technologies, data analytics, and automation to enable accurate detection, identification, and timely reporting of debris. Continuous real-time monitoring of the airfield environment allows early identification of potential hazards, significantly reducing risks and operational disruptions caused by FOD incidents. Automation within the system enhances response coordination by ensuring swift and appropriate corrective actions are taken once debris is detected, thereby minimizing safety threats and delays. In addition, the study employs a dual strengths, weaknesses, opportunities, and threats framework, combined with a comparative regulatory analysis of guidelines issued by the Federal Aviation Administration, the European Union Aviation Safety Agency, and the National Civil Aviation Agency. This integrated approach supports informed decision-making for electric vertical takeoff and landing aircraft integration and vertiport deployment within Urban Air Mobility ecosystems.
- 27 February 2024
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 66 (9) , 1494-1509
Influence of IP-TIG welding parameters on weld bead geometry, tensile properties, and microstructure of Ti6Al4V alloy joints
The primary aim of this study is to analyze the influence of inter-pulse tungsten inert gas (IP-TIG) welding parameters (peak current, inter-pulse current, and inter-pulse frequency) on weld bead geometry, tensile properties, and microstructure of Ti6Al4V alloy joints for gas turbine applications. IP-TIG welding principally featured by magnetic arc constriction and pulsing was employed to overcome the high heat input problems in TIG welding of thin Ti6Al4V alloy sheets such as wider bead and HAZ, coarsening of beta grains, inferior ductility, distortion of joints, and atmospheric contamination which significantly deteriorates the mechanical performance of welded sheets. The tensile properties and microhardness of IP-TIG joints were evaluated and correlated to the microstructural features. The microstructural features were analyzed using optical microscopy. The fractured surfaces of tensile specimens were studied using scanning electron microscopy. Results showed that the Ti6Al4V alloy joints developed using peak current of 50 A, inter-pulse current of 30 A, and inter-pulse frequency of 20 kHz exhibited greater strength, hardness and elongation. It showed greater tensile strength of 1030 MPa, yield strength of 981 MPa, and elongation of 10 % and FZ microhardness of 391 HV 0.2 . It is mainly due to the development of refined grains in fusion zone (FZ).
- 27 February 2024
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 66 (9) , 1494-1509
Influence of IP-TIG welding parameters on weld bead geometry, tensile properties, and microstructure of Ti6Al4V alloy joints
The primary aim of this study is to analyze the influence of inter-pulse tungsten inert gas (IP-TIG) welding parameters (peak current, inter-pulse current, and inter-pulse frequency) on weld bead geometry, tensile properties, and microstructure of Ti6Al4V alloy joints for gas turbine applications. IP-TIG welding principally featured by magnetic arc constriction and pulsing was employed to overcome the high heat input problems in TIG welding of thin Ti6Al4V alloy sheets such as wider bead and HAZ, coarsening of beta grains, inferior ductility, distortion of joints, and atmospheric contamination which significantly deteriorates the mechanical performance of welded sheets. The tensile properties and microhardness of IP-TIG joints were evaluated and correlated to the microstructural features. The microstructural features were analyzed using optical microscopy. The fractured surfaces of tensile specimens were studied using scanning electron microscopy. Results showed that the Ti6Al4V alloy joints developed using peak current of 50 A, inter-pulse current of 30 A, and inter-pulse frequency of 20 kHz exhibited greater strength, hardness and elongation. It showed greater tensile strength of 1030 MPa, yield strength of 981 MPa, and elongation of 10 % and FZ microhardness of 391 HV 0.2 . It is mainly due to the development of refined grains in fusion zone (FZ).
- 19 May 2023
- Published by ASME International in Journal of Engineering Materials and Technology
- Vol. 145 (4) , 1-30
Influence of Diffusion Bonding Pressure on Microstructural Features and Strength Performance of Dissimilar Ti–6Al–4V Alloy and AISI 304 Steel Joints Developed Using Copper Interlayer
The joining of Ti–6Al–4V (Ti64) alloy and AISI 304 austenitic stainless steel (ASS 304) carries significant importance in aeroengines for turbine blade applications. However, it is difficult to join using fusion welding. The fusion welding of Ti64 alloy and ASS 304 steel promotes the evolution of various Fe–Cr–Ti and Fe–Ti intermetallics in weld zone owing to limited solid solubility of Fe, Cr, Ti, and Ni with each other. The evolution of these intermetallics deteriorates the strength performance of joints. Hence for joining Ti64 alloy and ASS 304 steel, vacuum diffusion bonding (VDB) method is employed with thin copper (Cu) foil as an interlayer. The DB pressure extends significant influence on microstructural evolution and strength of joints. So, for the feasibility of joining Ti64 alloy and ASS 304 steel, the effect of DB pressure on microstructure and strength of joints is investigated. Results showed that the dissimilar joints of Ti64 alloy and ASS 304 steel developed using the DB pressure of 14 MPa exhibited greater lap shear strength (LSS) and bonding strength (BS) of 180 MPa and 268 MPa, respectively. It is attributed to the improved coalescence of joining interface and the development of ideal bonding width with the least amount of embrittlement consequences. An increase in DB pressure increases the width of the diffusion region which promotes the development of detrimental intermetallics of Ti–Fe and deteriorates the strength of dissimilar joints.
- 19 May 2023
- Published by ASME International in Journal of Engineering Materials and Technology
- Vol. 145 (4) , 1-30
Influence of Diffusion Bonding Pressure on Microstructural Features and Strength Performance of Dissimilar Ti–6Al–4V Alloy and AISI 304 Steel Joints Developed Using Copper Interlayer
The joining of Ti–6Al–4V (Ti64) alloy and AISI 304 austenitic stainless steel (ASS 304) carries significant importance in aeroengines for turbine blade applications. However, it is difficult to join using fusion welding. The fusion welding of Ti64 alloy and ASS 304 steel promotes the evolution of various Fe–Cr–Ti and Fe–Ti intermetallics in weld zone owing to limited solid solubility of Fe, Cr, Ti, and Ni with each other. The evolution of these intermetallics deteriorates the strength performance of joints. Hence for joining Ti64 alloy and ASS 304 steel, vacuum diffusion bonding (VDB) method is employed with thin copper (Cu) foil as an interlayer. The DB pressure extends significant influence on microstructural evolution and strength of joints. So, for the feasibility of joining Ti64 alloy and ASS 304 steel, the effect of DB pressure on microstructure and strength of joints is investigated. Results showed that the dissimilar joints of Ti64 alloy and ASS 304 steel developed using the DB pressure of 14 MPa exhibited greater lap shear strength (LSS) and bonding strength (BS) of 180 MPa and 268 MPa, respectively. It is attributed to the improved coalescence of joining interface and the development of ideal bonding width with the least amount of embrittlement consequences. An increase in DB pressure increases the width of the diffusion region which promotes the development of detrimental intermetallics of Ti–Fe and deteriorates the strength of dissimilar joints.
- 1 January 2023
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 65 (1) , 77-86
Effect of diffusion bonding time on microstructure and mechanical properties of dissimilar Ti6Al4V titanium alloy and AISI 304 austenitic stainless steel joints
The main objective of this investigation is to study the effect of diffusion bonding time on microstructure and mechanical properties of dissimilar Ti6Al4V titanium alloy and AISI 304 austenitic stainless steel joints. The dissimilar joints of Ti6Al4V titanium alloy and AISI 304 steel were developed using the different levels of bonding time (30, 45, 60, 75 and 90 min) in a vacuum chamber at a bonding temperature of 900 °C and compressive pressure of 14 MPa. The microstructure of joints was analyzed using optical microscopy (OM) and scanning electron microscopy (SEM). The elemental analysis of joint interface was studied using the SEM energy dispersive spectroscopy (EDS). The evolution of intermetallic compounds at the joint interface was analyzed using X-ray diffraction (XRD). The ram tensile tests and lap shear tests were performed to assess the bonding strength and lap shear strength of dissimilar joints. Results showed that the dissimilar joints of Ti6Al4V alloy–AISI 304 steel developed using the diffusion bonding time of 75 min showed higher lap shear strength of 151 MPa and bonding strength of 244 MPa due to the better coalescence of the joining surfaces and evolution of optimum width of diffusion region having minimum embrittlement effects.
- 1 January 2023
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 65 (1) , 77-86
Effect of diffusion bonding time on microstructure and mechanical properties of dissimilar Ti6Al4V titanium alloy and AISI 304 austenitic stainless steel joints
The main objective of this investigation is to study the effect of diffusion bonding time on microstructure and mechanical properties of dissimilar Ti6Al4V titanium alloy and AISI 304 austenitic stainless steel joints. The dissimilar joints of Ti6Al4V titanium alloy and AISI 304 steel were developed using the different levels of bonding time (30, 45, 60, 75 and 90 min) in a vacuum chamber at a bonding temperature of 900 °C and compressive pressure of 14 MPa. The microstructure of joints was analyzed using optical microscopy (OM) and scanning electron microscopy (SEM). The elemental analysis of joint interface was studied using the SEM energy dispersive spectroscopy (EDS). The evolution of intermetallic compounds at the joint interface was analyzed using X-ray diffraction (XRD). The ram tensile tests and lap shear tests were performed to assess the bonding strength and lap shear strength of dissimilar joints. Results showed that the dissimilar joints of Ti6Al4V alloy–AISI 304 steel developed using the diffusion bonding time of 75 min showed higher lap shear strength of 151 MPa and bonding strength of 244 MPa due to the better coalescence of the joining surfaces and evolution of optimum width of diffusion region having minimum embrittlement effects.
- Open Access
- 9 December 2022
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2022, 1-15
Experimental Investigation on Microstructure and Mechanical Properties of Friction Welded Dissimilar Alloys
High-temperature dissimilar connections built of Inconel 718 and AISI 410 martensitic stainless steel (MSS) are widely used in a range of industries, including boiler construction, the chemical industry, aerospace, and nuclear. When compared to other materials, Inconel 718 and AISI 410 martensitic stainless steel offer superior strength and corrosion resistance under a variety of environmental conditions. The rotational speed was adjusted between 1100 and 1500 RPM, while the friction pressure, friction time, forging pressure, and forging duration were all kept constant during the testing. Five sets of testing were performed, with the resultant tensile strength (both room temperature and hot tensile) and Vickers Hardness being recorded for each set of trials. To assess the structural integrity of the joints, a detailed microstructural investigation, SEM-EDS, and XRD were performed at their interfaces. Mechanical properties were revealed to be high at 1300 RPM due to the small grain size at the interface region; ultimate tensile strength and hardness were determined to be 571 MPa and 423 HV, respectively, due to the small grain size at the interface region. Additionally, a pitting corrosion study has been conducted on dissimilar welded joints at optimum conditions, and their results were discussed and compared with base metals.
- 9 December 2022
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2022, 1-15
Open AccessExperimental Investigation on Microstructure and Mechanical Properties of Friction Welded Dissimilar Alloys
High-temperature dissimilar connections built of Inconel 718 and AISI 410 martensitic stainless steel (MSS) are widely used in a range of industries, including boiler construction, the chemical industry, aerospace, and nuclear. When compared to other materials, Inconel 718 and AISI 410 martensitic stainless steel offer superior strength and corrosion resistance under a variety of environmental conditions. The rotational speed was adjusted between 1100 and 1500 RPM, while the friction pressure, friction time, forging pressure, and forging duration were all kept constant during the testing. Five sets of testing were performed, with the resultant tensile strength (both room temperature and hot tensile) and Vickers Hardness being recorded for each set of trials. To assess the structural integrity of the joints, a detailed microstructural investigation, SEM-EDS, and XRD were performed at their interfaces. Mechanical properties were revealed to be high at 1300 RPM due to the small grain size at the interface region; ultimate tensile strength and hardness were determined to be 571 MPa and 423 HV, respectively, due to the small grain size at the interface region. Additionally, a pitting corrosion study has been conducted on dissimilar welded joints at optimum conditions, and their results were discussed and compared with base metals.
- Open Access
- 1 January 2021
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2021 (1)
Investigation on Processing Maps of Diffusion Bonding Process Parameters for Ti‐6Al‐4 V/AISI304 Dissimilar Joints
The diffusion bonding (DB) method is used in this investigation to connect high‐temperature dissimilar materials. The existence of difficult‐to‐remove oxide coatings on the titanium surfaces, as well as the arrangement of breakable metallic interlayers and oxide enclosures inside the bond region, provides the most significant challenges during the transition from AISI304 to Ti‐6Al‐4V alloying. In addition, an effort was made to advance DB processing maps for the operational connection of Ti‐6Al‐4V to AISI304 alloys to improve their performance. Joints had been created by combining several process factors, such as bonding temperature (T), bonding pressure (P), and holding time (t), to create diverse designs. Based on the findings, database processing maps were created. This set of processing maps may be used as a rough guideline for selecting appropriate DB process parameters for generating virtuous excellent bonds between Ti‐6Al‐4V and AISI304 alloys. The maximum lap shear strength (LSS) was achieved at 800°C, 15 MPa, and 45 min.
- 1 January 2021
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2021 (1)
Open AccessInvestigation on Processing Maps of Diffusion Bonding Process Parameters for Ti‐6Al‐4 V/AISI304 Dissimilar Joints
The diffusion bonding (DB) method is used in this investigation to connect high‐temperature dissimilar materials. The existence of difficult‐to‐remove oxide coatings on the titanium surfaces, as well as the arrangement of breakable metallic interlayers and oxide enclosures inside the bond region, provides the most significant challenges during the transition from AISI304 to Ti‐6Al‐4V alloying. In addition, an effort was made to advance DB processing maps for the operational connection of Ti‐6Al‐4V to AISI304 alloys to improve their performance. Joints had been created by combining several process factors, such as bonding temperature (T), bonding pressure (P), and holding time (t), to create diverse designs. Based on the findings, database processing maps were created. This set of processing maps may be used as a rough guideline for selecting appropriate DB process parameters for generating virtuous excellent bonds between Ti‐6Al‐4V and AISI304 alloys. The maximum lap shear strength (LSS) was achieved at 800°C, 15 MPa, and 45 min.
- 4 November 2019
- Published by Emerald Publishing in Multidiscipline Modeling in Materials and Structures
- Vol. 15 (6) , 1037-1052
Optimization of Ti-6Al-4V/AISI304 diffusion bonding process parameters using RSM and PSO algorithm
Purpose: The purpose of this paper is to develop an empirical relationship for predicting the strength of titanium to austenitic stainless steel fabricated by diffusion bonding (DB) process. Process parameters such as bonding pressure, bonding temperature and holding time play the main role in deciding the joint strength. Design/methodology/approach: In this study, three-factors, five-level central composite rotatable design was used to conduct the minimum number of experiments involving all the combinations of parameters. Findings: An empirical relationship was developed to predict the lap shear strength (LSS) of the joints incorporating DB process parameters. The developed empirical relationship was optimized using particle swarm optimization (PSO). The optimized value discovered through PSO was compared with the response surface methodology (RSM). The joints produced using bonding pressure of 14 MPa, bonding temperature of 900°C and holding time of 70 min exhibited a maximum LSS of 150.51 MPa in comparison with other joints. This was confirmed by constructing response graphs and contour plots. Originality/value: Optimizing the DB parameters using RSM and PSO, PSO gives an accurate result when compared with RSM. Also, a sensitivity analysis is carried out to identify the most influencing parameter for the DB process.
- 4 November 2019
- Published by Emerald Publishing in Multidiscipline Modeling in Materials and Structures
- Vol. 15 (6) , 1037-1052
Optimization of Ti-6Al-4V/AISI304 diffusion bonding process parameters using RSM and PSO algorithm
Purpose: The purpose of this paper is to develop an empirical relationship for predicting the strength of titanium to austenitic stainless steel fabricated by diffusion bonding (DB) process. Process parameters such as bonding pressure, bonding temperature and holding time play the main role in deciding the joint strength. Design/methodology/approach: In this study, three-factors, five-level central composite rotatable design was used to conduct the minimum number of experiments involving all the combinations of parameters. Findings: An empirical relationship was developed to predict the lap shear strength (LSS) of the joints incorporating DB process parameters. The developed empirical relationship was optimized using particle swarm optimization (PSO). The optimized value discovered through PSO was compared with the response surface methodology (RSM). The joints produced using bonding pressure of 14 MPa, bonding temperature of 900°C and holding time of 70 min exhibited a maximum LSS of 150.51 MPa in comparison with other joints. This was confirmed by constructing response graphs and contour plots. Originality/value: Optimizing the DB parameters using RSM and PSO, PSO gives an accurate result when compared with RSM. Also, a sensitivity analysis is carried out to identify the most influencing parameter for the DB process.