Xiao Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Interests
Xiao Liu has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Osman A. Basaran
Purdue University, Davidson School of Chemical Engineering, 480 Stadium Mall Drive West Lafayette, Indiana 47907-2100, USA
3 shared publications Brayden W. Wagoner
Davidson School of Chemical Engineering, Purdue University, 480 Stadium Mall Drive, West Lafayette, Indiana 47907, USA
2 shared publicationsHansol Wee
Purdue University, West Lafayette
2 shared publicationsAjay Harishankar Kumar
Purdue University, West Lafayette
1 shared publication
Latest Publications
- 9 October 2024
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 9 (10)
Escape from pinch-off during contraction of liquid sheets and two-dimensional drops of low-viscosity fluids
- 9 October 2024
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 9 (10)
Escape from pinch-off during contraction of liquid sheets and two-dimensional drops of low-viscosity fluids
- 26 December 2022
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 7 (12) , L121601
Contraction velocity of viscoelastic filaments
Liquid filaments, which are commonplace in daily life, nature, and technology, including inkjet printing and crop spraying, contract due to surface tension: they either retract into a single sphere or break up to produce a primary drop(s) and several smaller satellites. The latter are undesirable because they reduce printing quality and cause pollution due to spray drift. Surfactants and/or polymer additives can be used to control filament contraction and breakup. It has recently been demonstrated experimentally that the velocity at which the tips of contracting filaments retract can be increased in viscoelastic filaments that contain polymer additives compared to purely Newtonian filaments. Here, simulations are used to investigate the contraction of viscoelastic filaments whose rheology is described by the Oldroyd-B model. Filaments produced from nozzles are expected to be prestressed when they begin to contract. It is shown that the velocity with which the tips of prestressed filaments retract is greatly increased compared to filaments in which the polymer molecules are relaxed. This enhancement is explained by examining the value of (: Elastic stress; : Rate-of-strain tensor), which can be positive or negative. This quantity is positive when the flow does work on the polymer molecules but negative when the molecules do work on the flow, i.e., when elastic recoiling or unloading takes place. In prestressed filaments, elastic unloading takes place because : The elastic stresses work by pulling the fluid in axially and pushing it out radially, thereby drastically increasing the tip velocity.- 26 December 2022
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 7 (12) , L121601
Contraction velocity of viscoelastic filaments
Liquid filaments, which are commonplace in daily life, nature, and technology, including inkjet printing and crop spraying, contract due to surface tension: they either retract into a single sphere or break up to produce a primary drop(s) and several smaller satellites. The latter are undesirable because they reduce printing quality and cause pollution due to spray drift. Surfactants and/or polymer additives can be used to control filament contraction and breakup. It has recently been demonstrated experimentally that the velocity at which the tips of contracting filaments retract can be increased in viscoelastic filaments that contain polymer additives compared to purely Newtonian filaments. Here, simulations are used to investigate the contraction of viscoelastic filaments whose rheology is described by the Oldroyd-B model. Filaments produced from nozzles are expected to be prestressed when they begin to contract. It is shown that the velocity with which the tips of prestressed filaments retract is greatly increased compared to filaments in which the polymer molecules are relaxed. This enhancement is explained by examining the value of (: Elastic stress; : Rate-of-strain tensor), which can be positive or negative. This quantity is positive when the flow does work on the polymer molecules but negative when the molecules do work on the flow, i.e., when elastic recoiling or unloading takes place. In prestressed filaments, elastic unloading takes place because : The elastic stresses work by pulling the fluid in axially and pushing it out radially, thereby drastically increasing the tip velocity.- 13 October 2021
- Published by Wiley in AIChE Journal
- Vol. 68 (2) , e17491
Effect of initial conditions on promotion and inhibition of breakup during filament contraction
Liquid filaments surrounded by a gas arise in nature and applications. As filaments contract, they either retract into spheres or disintegrate to form numerous droplets. In most previous computational studies, the filament's initial shape at time t = 0 has been idealized as a perfect cylinder capped off at both ends by identical hemispheres (radii R) and the fluid within which is at rest. Motivated by the fact that in experiments and applications the filament fluid is often not quiescent at t = 0, the effect of a nonzero initial velocity profile is examined for Newtonian filaments. A comprehensive phase diagram is presented in the space of L0 (initial aspect ratio) and vz,max (initial tip velocity) for filaments of intermediate Ohnesorge number (density ρ, viscosity μ, and surface tension γ) that delineates regions of the parameter space where breakup occurs from those where filaments contract to spheres without breakup.
- 13 October 2021
- Published by Wiley in AIChE Journal
- Vol. 68 (2) , e17491
Effect of initial conditions on promotion and inhibition of breakup during filament contraction
Liquid filaments surrounded by a gas arise in nature and applications. As filaments contract, they either retract into spheres or disintegrate to form numerous droplets. In most previous computational studies, the filament's initial shape at time t = 0 has been idealized as a perfect cylinder capped off at both ends by identical hemispheres (radii R) and the fluid within which is at rest. Motivated by the fact that in experiments and applications the filament fluid is often not quiescent at t = 0, the effect of a nonzero initial velocity profile is examined for Newtonian filaments. A comprehensive phase diagram is presented in the space of L0 (initial aspect ratio) and vz,max (initial tip velocity) for filaments of intermediate Ohnesorge number (density ρ, viscosity μ, and surface tension γ) that delineates regions of the parameter space where breakup occurs from those where filaments contract to spheres without breakup.