Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Rajeevkaran Paranthaman has a total of 5 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Dielectric Characterization Using Reflected Group Delay of a Partially-Filled Coaxial Resonator

    by Gaurav Walia, Paul D. Laforge, Shahid Azam, Rajeevkaran Paranthaman

    This paper features an effective and novel method to characterize dielectric materials using the reflected group delay of an over-coupled partially-filled coaxial resonator. The method employs a simple and cost-effective approach by utilizing one-port measurements from a Vector Network Analyzer to determine the dielectric constant and loss tangent of a dielectric material filled inside a coaxial resonator. Simulations using Advanced Design System by PathWave and ANSYS Electronics Desktop are done to test the mathematical model under different scenarios. Based on the results obtained from simulations, the proposed method can determine the dielectric constant and loss tangent with an error of less than 2% and 30% respectively, when operated to have a coupling coefficient in the range of 2.5 to 10. A region of confidence is derived by taking into account the effect of systematic errors to determine the maximum expected error in the calculated values of dielectric constant and loss tangent. The region of confidence describes that the resonator when filled to more than 50% of its capacity to have coupling coefficient greater than 2.5 can determine the dielectric constant and loss tangent of a material with an error of less than 5% and 80% respectively. However, by limiting the value of coupling coefficient the error in the loss tangent can be restricted under 30%. A coaxial resonator is designed and fabricated, and Teflon is tested in order to validate the proposed method. A hollow Teflon rod is tested twice for different values of coupling capacitance to confirm the repeatability of the method. Soil samples with different moisture contents are tested to confirm the capacity of the method in testing different types of materials. Each of the soil sample is tested three times and standard deviation in the calculated values of the dielectric properties re-confirmed the repeatability of the method. The proposed method is considered appropriate to test the dielectric properties of solid materials which can be machined to fit inside the hollow cavity of the resonator and other materials like soils, fine particle solids, grains and liquids.


  • Open Access

    Spatial Variability during Shrinkage Testing of Expansive Clays

    by Rajeevkaran Paranthaman, Jared Suchan, Shahid Azam

    Civil infrastructure constructed with, buried in, or underlain by expansive clays is affected by high volumetric changes, especially because large-scale facilities are spatially distributed. This research focused on determining spatial variability during the shrinkage testing of expansive clays. An initially saturated sample (600 mm in diameter) of a high-plasticity clay was exposed to desiccation and thoroughly monitored over five months. The results indicated an expansive clay (30% smectite and 14% illite) in alkaline-pore water (695 mg/L Na+ and 1150 mg/L SO42−) for developing a dispersive soil fabric. The vertical shrinkage in the intact-soil portion was unchanged (remaining at 114 × 106 mm3) in the first 10 days, sharply decreased the initial volume by 30% (up to 280 mm or 80 × 106 mm3) in 68 days, and slowly decreased the initial volume by 40% (up to 240 mm or 68 × 106 mm3) in 145 days. Furthermore, the soil temperature was found to be 10% lower than the air temperature, whereas the relative humidity within the cell was found to be 30% higher than that outside the cell. The soil showed an initial prominent central ridge with a few cracks that gradually evolved into a distinct crack pattern with equal-sized and irregular soil chunks. The average soil surface showed no volume reduction up to 18 days and a subsequent linear reduction, reaching 25% of the initial soil volume by the end of the test.


  • Open Access

    Effect of Composition on Engineering Behavior of Clay Tills

    by Rajeevkaran Paranthaman, Shahid Azam

    Glacial geology, marine environment, and arid climate govern the composition of clay tills. The main purpose of this work is to develop a clear understanding of the engineering behavior of compacted clay till under soil suction and applied stress. The results indicate moderate water adsorption due to the presence of clay minerals (26% corrensite, 10% illite, and 8% kaolinite) with Ca2+ as the dominant cation and a flocculated fabric in a slightly basic (pH = 7.5) pore water. The water retention curve comprised four transition points that are associated with capillary water drainage from large pores (air entry value of 2 kPa and residual suction value of 20 kPa) and small pores (air entry value of 700 kPa and residual suction value of 5 × 104 kPa). Beyond the last value, vapor flow is dominant and removes the adsorbed water by evaporation. The ratio of soil volume change to water volume change best described the s-shaped shrinkage path that also comprised four stages, namely: from most large pores with low volume change; from remaining large and most small pores along with almost equal volume change; from some small pores with low volume change; and from the rest of the small pores with no volume change. Likewise, the s-shaped swelling potential curve comprised three stages and correlated well with bimodal hydraulic conductivity curve, that is, slow initial swelling (unsaturated hydraulic conductivity around 10−14 m/s) due to expansion of peripheral clay in lumps; high primary swelling (unsaturated hydraulic conductivity of up to 10−11 m/s) due to thickened double layer of most colloids; and slow secondary swelling (albeit unsaturated hydraulic conductivity around 10−10 m/s) due to expansion of remaining particles. Soil compression (compression index of 0.164) was due to a gradual reduction in number of large pores, whereas rebound (swelling index of 0.047) was due to water adsorption on clay with part of the deformations recovered. Finally, the consolidation rate was related to saturated hydraulic conductivity, which varied by three orders of magnitude.