Chakaravarthy Ezilarasan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Chakaravarthy Ezilarasan has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
B. Ravi
Department of Mechanical Engineering, Swarna Bharathi Institute of Science and Technology Khammam, Telangana, India
1 shared publication- Bommi Rammohan
Department of ECE, Chennai Institute of Technology, Chennai, India
1 shared publication - Duraivelu Jayabalakrishnan
Department of Mechanical Engineering Chennai Institute of Technology Chennai India
1 shared publication - G. Elias
Department of Mechanical Engineering, College of Electrical and Mechanical Engineering, Addis Ababa Science and Technology University, Addis Ababa, Ethiopia
1 shared publication - J. Francis Xavier
School of Mechanical Engineering, VIT Bhopal University, Sehore, India
1 shared publication - M. Thenmozhi
Department of Computer Science, Sona College of Arts and science, Salem, India
1 shared publication
Latest Publications
- Open Access
- 1 January 2022
- Published by Wiley in Journal of Nanomaterials
- Vol. 2022 (1)
Surface Roughness Evaluation in Turning of Nimonic C263 Super Alloy Using 2D DWT Histogram Equalization
Surface roughness of specimens is an important area of research since it influences the performance of machined parts. Meanwhile, employing a vision system to judge the roughness of the machined surface of specimens via captured images acquired from the specimen is an innovative and extensively used method. In this investigation, a vision system is used to capture the SEM images of the machined surface. The two‐dimensional images of the machined surface of the Nimonic263 alloy are used to approximate the profile of the surface of specimens in finish turning. Surface roughness was detected in simulated images of specimens in a variety of machining conditions using the imaging technology. In this research work, the surface texture is extracted using a technique that combines 2D surface images and wavelet transform approach. The 2D wavelet transform has the capability to disintegrate a machined surface image into multiresolution depiction for several surface characteristics and can be utilized for surface evaluation. The difference in the histogram frequency of an illuminated region of interest (ROI) from turned surface images was analyzed to aid in the evaluation of surface roughness with an average prediction error of less than 3.2%.
- 1 January 2022
- Published by Wiley in Journal of Nanomaterials
- Vol. 2022 (1)
Open AccessSurface Roughness Evaluation in Turning of Nimonic C263 Super Alloy Using 2D DWT Histogram Equalization
Surface roughness of specimens is an important area of research since it influences the performance of machined parts. Meanwhile, employing a vision system to judge the roughness of the machined surface of specimens via captured images acquired from the specimen is an innovative and extensively used method. In this investigation, a vision system is used to capture the SEM images of the machined surface. The two‐dimensional images of the machined surface of the Nimonic263 alloy are used to approximate the profile of the surface of specimens in finish turning. Surface roughness was detected in simulated images of specimens in a variety of machining conditions using the imaging technology. In this research work, the surface texture is extracted using a technique that combines 2D surface images and wavelet transform approach. The 2D wavelet transform has the capability to disintegrate a machined surface image into multiresolution depiction for several surface characteristics and can be utilized for surface evaluation. The difference in the histogram frequency of an illuminated region of interest (ROI) from turned surface images was analyzed to aid in the evaluation of surface roughness with an average prediction error of less than 3.2%.
- RetractedOpen Access
- 12 October 2021
- Published by Wiley in Journal of Nanomaterials
- Vol. 2021, 1-11
Experimental Study on Surface Roughness and Flank Wear in Turning of Nimonic C263 under Dry Cutting Conditions
Aircraft component manufacturing sector is looking for high precision machining in aircraft components. The present work explores the operability of green manufacturing of Nimonic C263 using dry turning. Nimonic C263 is tough to turn owing to its inherent quality like low conductivity and more work hardening. Therefore, in order to improve this machined surface/integrity, the controlling factors were optimized based on desirability approach for minimum of surface roughness and flank wear during turning of this alloy using CBN insert. L27 orthogonal array was chosen to carry out the experiment. The effects of controlling factors, such as cutting speed (), feed rate (), and cut penetration/depth of cut () on the outputs, were also explored. The feed rate was a major impact to affect surface finish and flank wear. The average error percentage between the experimental and RSM models for surface finish was 4.76 percent and 2.79 percent for flank wear.
- 12 October 2021
- Published by Wiley in Journal of Nanomaterials
- Vol. 2021, 1-11
RetractedOpen AccessExperimental Study on Surface Roughness and Flank Wear in Turning of Nimonic C263 under Dry Cutting Conditions
Aircraft component manufacturing sector is looking for high precision machining in aircraft components. The present work explores the operability of green manufacturing of Nimonic C263 using dry turning. Nimonic C263 is tough to turn owing to its inherent quality like low conductivity and more work hardening. Therefore, in order to improve this machined surface/integrity, the controlling factors were optimized based on desirability approach for minimum of surface roughness and flank wear during turning of this alloy using CBN insert. L27 orthogonal array was chosen to carry out the experiment. The effects of controlling factors, such as cutting speed (), feed rate (), and cut penetration/depth of cut () on the outputs, were also explored. The feed rate was a major impact to affect surface finish and flank wear. The average error percentage between the experimental and RSM models for surface finish was 4.76 percent and 2.79 percent for flank wear.