Boli Peng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Boli Peng has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Michael Schröter
Chair for Electron Devices and Integrated Circuits, Technical University Dresden, Dresden, Germany
2 shared publications - Klaus Aufinger
Infineon Technologies AG, Neubiberg, Germany
1 shared publication Manojkumar Annamalai
Chair for Electron Devices and Integrated Circuits, Technische Universität Dresden, Dresden, Germany
1 shared publicationMichael Schröter
Chair for Electron Devices and Integrated Circuits, Technische Universität Dresden, Dresden, Germany
1 shared publicationSven Mothes
GLOBALFOUNDRIES, Dresden, Germany
1 shared publication- Xiaodi Jin
Chair for Electron Devices and Integrated Circuits, Dresden University of Technology (TU Dresden), Dresden, Germany
1 shared publication
Latest Publications
- 28 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (7) , 1045-1048
A 232–282 GHz Frequency Quadrupler in 130-nm SiGe HBT SG13G3Cu Technology
A 232–282 frequency quadrupler has been designed and fabricated using Leibniz Institute for High Performance Microelectronics (IHP’s) highest performance 130-nm SiGe BiCMOS technology, featuring $f_{T}$ / $f_{\text {MAX}}$ values of 470/650 GHz. It consists of stacked Gilbert-cell (GC) doublers, with neutralization capacitances in the transconductance pair to enhance conversion gain (CG), and a miniaturized balun structure for the low frequency differential input signal generation. The frequency quadrupler achieves a peak output power of –4.5dBm, corresponding to a 3.5 dB CG at 236 GHz, with a 0.56% dc-to-RF efficiency and a 3 dB bandwidth of 50 GHz ranging from 232 to 282 GHz. This performance is realized with a dc power consumption of only 63 mW and a chip area of 0.49 mm2.
- 28 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (7) , 1045-1048
A 232–282 GHz Frequency Quadrupler in 130-nm SiGe HBT SG13G3Cu Technology
A 232–282 frequency quadrupler has been designed and fabricated using Leibniz Institute for High Performance Microelectronics (IHP’s) highest performance 130-nm SiGe BiCMOS technology, featuring $f_{T}$ / $f_{\text {MAX}}$ values of 470/650 GHz. It consists of stacked Gilbert-cell (GC) doublers, with neutralization capacitances in the transconductance pair to enhance conversion gain (CG), and a miniaturized balun structure for the low frequency differential input signal generation. The frequency quadrupler achieves a peak output power of –4.5dBm, corresponding to a 3.5 dB CG at 236 GHz, with a 0.56% dc-to-RF efficiency and a 3 dB bandwidth of 50 GHz ranging from 232 to 282 GHz. This performance is realized with a dc power consumption of only 63 mW and a chip area of 0.49 mm2.
- 15 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 34 (1) , 61-64
A Cryogenic 561 μW Ultralow-Power 56–62 GHz Low Noise Amplifier in 130-nm SiGe HBTs
An ultralow-power millimeter-wave (mm-wave) cryogenic low noise amplifier (LNA) has been designed and fabricated in a 130 nm SiGe HBT technology. Measurements at 4.3 K show a peak gain of 18.3 dB at 58 GHz and a simulated average noise figure of 1.28 dB across the 56–62 GHz frequency band. The respective power consumption of just 561 $\mu$ W is, to the best of the authors’ knowledge, the lowest one reported so far for a cryogenic mm-wave LNA. The circuit design has been enabled by a HICUM/L2 compact model with various physics-based extensions for capturing the low-temperature HBT behavior. The model shows good accuracy over a large bias and frequency range for temperatures down to 4.3 K.
- 15 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 34 (1) , 61-64
A Cryogenic 561 μW Ultralow-Power 56–62 GHz Low Noise Amplifier in 130-nm SiGe HBTs
An ultralow-power millimeter-wave (mm-wave) cryogenic low noise amplifier (LNA) has been designed and fabricated in a 130 nm SiGe HBT technology. Measurements at 4.3 K show a peak gain of 18.3 dB at 58 GHz and a simulated average noise figure of 1.28 dB across the 56–62 GHz frequency band. The respective power consumption of just 561 $\mu$ W is, to the best of the authors’ knowledge, the lowest one reported so far for a cryogenic mm-wave LNA. The circuit design has been enabled by a HICUM/L2 compact model with various physics-based extensions for capturing the low-temperature HBT behavior. The model shows good accuracy over a large bias and frequency range for temperatures down to 4.3 K.
- Open Access
- 16 October 2021
- Published by Springer Nature in Journal of Computational Electronics
- Vol. 20 (6) , 2492-2500
Device design and optimization of CNTFETs for high-frequency applications
Carbon nanotube (CNT) field-effect transistors (FETs) have recently reached high-frequency (HF) performance similar to that of silicon RF-CMOS at the same gate length despite a tube density and current per tube that are far from the physical limits and suboptimal device architecture. This work reports on an investigation of the optimal device design for practical HF applications in terms of cut-off frequencies, power gain, and linearity. Different fundamental designs in the gate contact arrangement are considered based on a 3D device simulation of both CNTs and contacts. First, unit cells with a single CNT and minimal contact sizes are compared. The resulting simulation data are then extended toward a structure with two gate fingers and realistic contact sizes. Corresponding parasitic capacitances, as well as series and contact resistances, have been included for obtaining realistic characteristics and figures of merit that can be used for comparison with corresponding silicon RF MOSFETs. Finally, a sensitivity analysis of the device architecture with the highest performance is performed in order to find the optimal device design space.
- 16 October 2021
- Published by Springer Nature in Journal of Computational Electronics
- Vol. 20 (6) , 2492-2500
Open AccessDevice design and optimization of CNTFETs for high-frequency applications
Carbon nanotube (CNT) field-effect transistors (FETs) have recently reached high-frequency (HF) performance similar to that of silicon RF-CMOS at the same gate length despite a tube density and current per tube that are far from the physical limits and suboptimal device architecture. This work reports on an investigation of the optimal device design for practical HF applications in terms of cut-off frequencies, power gain, and linearity. Different fundamental designs in the gate contact arrangement are considered based on a 3D device simulation of both CNTs and contacts. First, unit cells with a single CNT and minimal contact sizes are compared. The resulting simulation data are then extended toward a structure with two gate fingers and realistic contact sizes. Corresponding parasitic capacitances, as well as series and contact resistances, have been included for obtaining realistic characteristics and figures of merit that can be used for comparison with corresponding silicon RF MOSFETs. Finally, a sensitivity analysis of the device architecture with the highest performance is performed in order to find the optimal device design space.