Dong Han Ko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Dong Han Ko has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- Seong-Ook Jung
Yonsei University
13 shared publications - Sehee Lim
School of Electrical and Electronic Engineering, Yonsei University, Seoul, South Korea
9 shared publications - Se Keon Kim
School of Electrical and Electronic Engineering, Yonsei University, Seoul, South Korea
6 shared publications - Giseok Kim
School of Electrical and Electronic Engineering, Yonsei University, Seoul, South Korea
4 shared publications - In-Jun Jung
School of Electrical and Electronic Engineering, Yonsei University, Seoul, South Korea
4 shared publications - Tae Woo Oh
School of Electrical and Electronic Engineering, Yonsei University, Seoul, South Korea
4 shared publications
Latest Publications
- 27 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. PP  (00189200) , 1-12
Dual-Mode Inverter-Based Write Termination Scheme for Energy- and Area-Efficient Write Operation in 28-nm 1T1MTJ STT-MRAM
Spin-transfer torque magnetic random access memory (STT-MRAM) is a promising non-volatile memory, but its write operation requires a large static current, leading to high write power. Resistance-monitoring write termination (RM-WT) schemes were introduced to reduce write power, but they suffer from several limitations: 1) the sensing circuit (SC) used in previous schemes has limited effective input voltage, degrading the robustness of WT; 2) the prior schemes cause severe area overhead due to the additional WT circuits besides sense amplifier (SA); and 3) the previous schemes cannot support write 0 termination, limiting write power reduction. This article proposes a dual-mode inverter-based write-termination (DMI-WT) circuit that resolves these limitations. In the proposed scheme, a single-ended inverter-based SC (INV-SC) is used, which doubles the effective input voltage without area overhead. In addition, self-referenced offset cancel (OC) is used, which enables robust WT and SA operation. DMI-WT enables WT operation for both write 0 and write 1 operation while simultaneously serving as an SA, thereby reducing the write power and removing the area overhead caused by WT circuits. A prototype chip fabricated in 28-nm CMOS technology with a 256-kb STT-MRAM array shows that DMI-WT achieves up to $6.39{\times }$ area overhead reduction, $7.5{\times }$ lower write power per bit at a 20-ns write access time, $1.27{\times }$ faster read access time, and $1.41{\times }$ lower read power compared with previous WT circuits using STT-MRAM.
- 27 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. PP  (00189200) , 1-12
Dual-Mode Inverter-Based Write Termination Scheme for Energy- and Area-Efficient Write Operation in 28-nm 1T1MTJ STT-MRAM
Spin-transfer torque magnetic random access memory (STT-MRAM) is a promising non-volatile memory, but its write operation requires a large static current, leading to high write power. Resistance-monitoring write termination (RM-WT) schemes were introduced to reduce write power, but they suffer from several limitations: 1) the sensing circuit (SC) used in previous schemes has limited effective input voltage, degrading the robustness of WT; 2) the prior schemes cause severe area overhead due to the additional WT circuits besides sense amplifier (SA); and 3) the previous schemes cannot support write 0 termination, limiting write power reduction. This article proposes a dual-mode inverter-based write-termination (DMI-WT) circuit that resolves these limitations. In the proposed scheme, a single-ended inverter-based SC (INV-SC) is used, which doubles the effective input voltage without area overhead. In addition, self-referenced offset cancel (OC) is used, which enables robust WT and SA operation. DMI-WT enables WT operation for both write 0 and write 1 operation while simultaneously serving as an SA, thereby reducing the write power and removing the area overhead caused by WT circuits. A prototype chip fabricated in 28-nm CMOS technology with a 256-kb STT-MRAM array shows that DMI-WT achieves up to $6.39{\times }$ area overhead reduction, $7.5{\times }$ lower write power per bit at a 20-ns write access time, $1.27{\times }$ faster read access time, and $1.41{\times }$ lower read power compared with previous WT circuits using STT-MRAM.
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 73  (9) , 1-14
A Wide-Range and Energy-Efficient Level Shifter With Robust Leakage-Suppressed Pull-Down Network
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 73  (9) , 1-14
A Wide-Range and Energy-Efficient Level Shifter With Robust Leakage-Suppressed Pull-Down Network
- 3 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61  (6) , 2965-2977
DPe-CIM: A 4T-1C Dual-Port eDRAM-Based Compute-in-Memory for Simultaneous Computing and Refresh With Adaptive Refresh and Data Conversion Reduction Scheme
This article presents DPe-CIM, a 4T-1C dual-port embedded dynamic random access memory (eDRAM)-based compute-in-memory (CIM) macro with adaptive refresh and data conversion reduction. DPe-CIM proposes four key features that improve area and energy efficiency: 1) dual-port eDRAM cell (DPC) separates the multiply-and-accumulate (MAC) and refresh ports, enabling simultaneous MAC and refresh (SMR) operation to eliminate wasted cycles for refresh; 2) adaptive refresh tracking (ART) eliminates unnecessary refresh power consumption; 3) bitline (BL) embedded DAC (BLe-DAC) enhances area and energy efficiency with BL capacitance reuse; 4) output-boosting ADC (OB-ADC) with charge analog adder (CAA) reduces ADC precision and number of ADC per row without accuracy loss to save area and energy in ADC, thereby overcoming CIM efficiency wall. The DPe-CIM is fabricated in 28-nm CMOS technology and occupies 0.0496 mm ${}^{\mathbf {2}}$ with 72-kb cell capacity. Its measured memory density is 1.42 Mb/mm ${}^{\mathbf {2}}$ , reaches a peak MAC density of 13.85 TOPS/mm ${}^{\mathbf {2}}$ , and a peak energy efficiency of 505.83 TOPS/W performing 4-b−4-b operations. DPe-CIM achieves $3.56\times $ higher computing efficiency figure of merit (FoM) than the previous CIM architectures.
- 3 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61  (6) , 2965-2977
DPe-CIM: A 4T-1C Dual-Port eDRAM-Based Compute-in-Memory for Simultaneous Computing and Refresh With Adaptive Refresh and Data Conversion Reduction Scheme
This article presents DPe-CIM, a 4T-1C dual-port embedded dynamic random access memory (eDRAM)-based compute-in-memory (CIM) macro with adaptive refresh and data conversion reduction. DPe-CIM proposes four key features that improve area and energy efficiency: 1) dual-port eDRAM cell (DPC) separates the multiply-and-accumulate (MAC) and refresh ports, enabling simultaneous MAC and refresh (SMR) operation to eliminate wasted cycles for refresh; 2) adaptive refresh tracking (ART) eliminates unnecessary refresh power consumption; 3) bitline (BL) embedded DAC (BLe-DAC) enhances area and energy efficiency with BL capacitance reuse; 4) output-boosting ADC (OB-ADC) with charge analog adder (CAA) reduces ADC precision and number of ADC per row without accuracy loss to save area and energy in ADC, thereby overcoming CIM efficiency wall. The DPe-CIM is fabricated in 28-nm CMOS technology and occupies 0.0496 mm ${}^{\mathbf {2}}$ with 72-kb cell capacity. Its measured memory density is 1.42 Mb/mm ${}^{\mathbf {2}}$ , reaches a peak MAC density of 13.85 TOPS/mm ${}^{\mathbf {2}}$ , and a peak energy efficiency of 505.83 TOPS/W performing 4-b−4-b operations. DPe-CIM achieves $3.56\times $ higher computing efficiency figure of merit (FoM) than the previous CIM architectures.
- 8 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61  (3) , 1216-1227
A 3× Offset, 2.9× Power, 1.3× Sensing Time, and 4× Area Reduction Direct Input Transfer Offset Cancel DRAM IO Sense Amplifier With Static Current-Free Pre-Sensing
With the increase in memory density and scaling down of the DRAM process, the length of the global IO pairs (GIO and GIOB) and the offset voltage ( $V_{\text {OS}}$ ) have increased. This degrades the power consumption and sensing time ( $t_{\text {SEN}}$ ) of IO sense amplifiers (IOSAs) that sense the differential input voltage via long GIO pairs ( $\Delta V_{\text {GIO}}$ ). Conventional IOSAs use the self-time logic, hybrid IOSA, and GIO switches to reduce the power consumption of IOSA. However, they do not consider $V_{\text {OS}}$ of the IOSA, which requires a larger $\Delta V_{\text {GIO}}$ for robust IOSA sensing operations, increasing $t_{\text {SEN}}$ to develop a large $\Delta V_{\text {GIO}}$ and increasing the power consumption to pre-charge these discharged GIO pairs. To mitigate these issues, offset cancellation (OC)-IOSA has been proposed. However, since two large coupling-capacitor-based OC-IOSAs transfer $\Delta V_{\text {GIO}}$ via capacitive coupling, it suffers from input voltage attenuation, severe area overhead, and static current. This work proposes a single capacitor-based direct input transfer static current-free pre-sensing IOSA (SCFP-IOSA) to reduce $V_{\text {OS}}$ and power consumption with a small area and high speed. The direct input transfer scheme is adopted in SCFP-IOSA, which removes input voltage attenuation and does not require large capacitors, thereby enhancing the sensing margin and relieving area overhead. In addition, a novel static current-free pre-sensing, which uses RC delay exponential nature, is proposed that not only pre-amplifies $\Delta V_{\text {GIO}}$ to enhance $V_{\text {OS}}$ tolerance but also reduces power consumption by removing static current during the pre-sense (PS) operation. The simultaneous coupling down and $\Delta V_{\text {GIO}}$ developing operation also contribute to the fast sensing operation of SCFP-IOSA. According to the measurement on the experimental chip fabricated in a 28-nm CMOS technology, SCFP-IOSA achieves three times lower $\sigma V_{\text {OS}}$ of 4.42 mV, 2.9 times lower power consumption of $2.15~{\mu }$ W, and 1.3 times faster $t_{\text {SEN}}$ of 3.75 ns with 4.46 times smaller area of $10.28~{\mu }$ m2 compared with the state-of-the-art OC-IOSA.
- 8 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61  (3) , 1216-1227
A 3× Offset, 2.9× Power, 1.3× Sensing Time, and 4× Area Reduction Direct Input Transfer Offset Cancel DRAM IO Sense Amplifier With Static Current-Free Pre-Sensing
With the increase in memory density and scaling down of the DRAM process, the length of the global IO pairs (GIO and GIOB) and the offset voltage ( $V_{\text {OS}}$ ) have increased. This degrades the power consumption and sensing time ( $t_{\text {SEN}}$ ) of IO sense amplifiers (IOSAs) that sense the differential input voltage via long GIO pairs ( $\Delta V_{\text {GIO}}$ ). Conventional IOSAs use the self-time logic, hybrid IOSA, and GIO switches to reduce the power consumption of IOSA. However, they do not consider $V_{\text {OS}}$ of the IOSA, which requires a larger $\Delta V_{\text {GIO}}$ for robust IOSA sensing operations, increasing $t_{\text {SEN}}$ to develop a large $\Delta V_{\text {GIO}}$ and increasing the power consumption to pre-charge these discharged GIO pairs. To mitigate these issues, offset cancellation (OC)-IOSA has been proposed. However, since two large coupling-capacitor-based OC-IOSAs transfer $\Delta V_{\text {GIO}}$ via capacitive coupling, it suffers from input voltage attenuation, severe area overhead, and static current. This work proposes a single capacitor-based direct input transfer static current-free pre-sensing IOSA (SCFP-IOSA) to reduce $V_{\text {OS}}$ and power consumption with a small area and high speed. The direct input transfer scheme is adopted in SCFP-IOSA, which removes input voltage attenuation and does not require large capacitors, thereby enhancing the sensing margin and relieving area overhead. In addition, a novel static current-free pre-sensing, which uses RC delay exponential nature, is proposed that not only pre-amplifies $\Delta V_{\text {GIO}}$ to enhance $V_{\text {OS}}$ tolerance but also reduces power consumption by removing static current during the pre-sense (PS) operation. The simultaneous coupling down and $\Delta V_{\text {GIO}}$ developing operation also contribute to the fast sensing operation of SCFP-IOSA. According to the measurement on the experimental chip fabricated in a 28-nm CMOS technology, SCFP-IOSA achieves three times lower $\sigma V_{\text {OS}}$ of 4.42 mV, 2.9 times lower power consumption of $2.15~{\mu }$ W, and 1.3 times faster $t_{\text {SEN}}$ of 3.75 ns with 4.46 times smaller area of $10.28~{\mu }$ m2 compared with the state-of-the-art OC-IOSA.
- 8 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 60  (6) , 2096-2105
Dual-Input Stacked Inverter-Based Single-Ended DRAM Sense Amplifier Using BL Switches for Low-Power High-Speed Sensing
Dynamic random access memory (DRAM) sensing capabilities have deteriorated with the reduced supply voltage and cell capacitance as the DRAM process scales down. Previous bitline sense amplifiers (BLSAs) use offset-canceling (OC) techniques based on capacitive coupling or current mirrors. However, these OC techniques induce substantial static power during the OC phase due to the transistors operating in the saturation region. In addition, the previous offset-canceling techniques have to precede charge sharing, resulting in additional timing overhead. Furthermore, the previous BLSAs suffer from a large area due to two capacitors, high sensitivity to ambient noise, and imbalanced sensing problems, which impedes them from being utilized for the highly scaled DRAM process. This article proposes a dual-input stacked inverter-based single-ended sense amplifier (DISA) to achieve improved sensing capability with reduced energy consumption, small area, and high speed. The dual-input stacked inverter in DISA significantly reduces the static current during both OC and main sensing phases while improving inverter gain. In addition, DISA achieves the smallest area compared to the previous BLSAs because of the use of a single capacitor in the single-ended structure. The simultaneous offset canceling and charge sharing also contribute to the fast sensing operation of DISA. According to the measurement on the experimental chip fabricated in a 28-nm CMOS technology, DISA achieves the shortest sensing time of $<$ 9 ns and the lowest sensing energy of 5.8 fJ/cycle/bit under 0.7-V $V_{\text{DD}}$ .
- 8 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 60  (6) , 2096-2105
Dual-Input Stacked Inverter-Based Single-Ended DRAM Sense Amplifier Using BL Switches for Low-Power High-Speed Sensing
Dynamic random access memory (DRAM) sensing capabilities have deteriorated with the reduced supply voltage and cell capacitance as the DRAM process scales down. Previous bitline sense amplifiers (BLSAs) use offset-canceling (OC) techniques based on capacitive coupling or current mirrors. However, these OC techniques induce substantial static power during the OC phase due to the transistors operating in the saturation region. In addition, the previous offset-canceling techniques have to precede charge sharing, resulting in additional timing overhead. Furthermore, the previous BLSAs suffer from a large area due to two capacitors, high sensitivity to ambient noise, and imbalanced sensing problems, which impedes them from being utilized for the highly scaled DRAM process. This article proposes a dual-input stacked inverter-based single-ended sense amplifier (DISA) to achieve improved sensing capability with reduced energy consumption, small area, and high speed. The dual-input stacked inverter in DISA significantly reduces the static current during both OC and main sensing phases while improving inverter gain. In addition, DISA achieves the smallest area compared to the previous BLSAs because of the use of a single capacitor in the single-ended structure. The simultaneous offset canceling and charge sharing also contribute to the fast sensing operation of DISA. According to the measurement on the experimental chip fabricated in a 28-nm CMOS technology, DISA achieves the shortest sensing time of $<$ 9 ns and the lowest sensing energy of 5.8 fJ/cycle/bit under 0.7-V $V_{\text{DD}}$ .
- 10 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Internet of Things Journal
- Vol. 11  (16) , 27676-27686
Design of Physically Unclonable Function Using Ferroelectric FET With Auto Write-Back Technique for Resource-Limited IoT Security
Physically unclonable function (PUF) is a lightweight encryption technique that generates random digital keys (responses) using intrinsic process variations of devices, which is a promising solution for Internet of Things (IoT) security due to its compatibility with constrained resources. Recent attempts to adopt nonvolatile memory (NVM) into PUFs have enhanced stability through a write-back technique that maintains consistent responses from the enrollment phase even under wide environmental variations by storing the response in the NVM device. However, the stability of the previous NVM PUFs is limited by the low on/off ratio of the NVMs. In addition, the circuit required to implement the write-back technique poses challenges of increased area and energy consumption. Considering the hardware limitations and power constraints of IoT devices, this paper proposes a ferroelectric field-effect transistor (FeFET) PUF as a suitable security solution. The high on/off ratio of FeFET and the proposed auto write-back technique that does not require additional circuitry realize the stability improvement (a bit error rate of <0.0001%) under wide environmental variations without incurring area and energy overheads. The negligible off current of FeFET prevents static power consumption, which leads to the lowest energy consumption of 6.70e-15 J during the response generation of the FeFET PUF. In addition, the compact PUF cell composed of two FeFETs achieves a high density of 87.37 F2.
- 10 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Internet of Things Journal
- Vol. 11  (16) , 27676-27686
Design of Physically Unclonable Function Using Ferroelectric FET With Auto Write-Back Technique for Resource-Limited IoT Security
Physically unclonable function (PUF) is a lightweight encryption technique that generates random digital keys (responses) using intrinsic process variations of devices, which is a promising solution for Internet of Things (IoT) security due to its compatibility with constrained resources. Recent attempts to adopt nonvolatile memory (NVM) into PUFs have enhanced stability through a write-back technique that maintains consistent responses from the enrollment phase even under wide environmental variations by storing the response in the NVM device. However, the stability of the previous NVM PUFs is limited by the low on/off ratio of the NVMs. In addition, the circuit required to implement the write-back technique poses challenges of increased area and energy consumption. Considering the hardware limitations and power constraints of IoT devices, this paper proposes a ferroelectric field-effect transistor (FeFET) PUF as a suitable security solution. The high on/off ratio of FeFET and the proposed auto write-back technique that does not require additional circuitry realize the stability improvement (a bit error rate of <0.0001%) under wide environmental variations without incurring area and energy overheads. The negligible off current of FeFET prevents static power consumption, which leads to the lowest energy consumption of 6.70e-15 J during the response generation of the FeFET PUF. In addition, the compact PUF cell composed of two FeFETs achieves a high density of 87.37 F2.
- 29 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 71  (4) , 1869-1873
Split WL 6T SRAM-Based Bit Serial Computing-in-Memory Macro With High Signal Margin and High Throughput
This paper proposes a split WL 6T SRAM computing-in-memory (CIM) macro for high signal margin and high throughput bit-serial multiply-accumulate (MAC) operation with 8-b input, 8-b weight, and 20-b output. The proposed architecture improves signal margin with input flipping WL control that limits the maximum number of turned-on WLs, throughput with a dual BL sensing scheme and pipelining, and energy efficiency with an input-aware trip point-based ADC and supply voltage adjustment of a near memory processor (NMP). The proposed architecture is fabricated in 65nm technology and achieves 152.32 bit-wise TOPS/W and 20.69 bit-wise TOPS/mm2. In addition, 91.23% inference accuracy at the CIFAR-10 image classification dataset with the ResNET-20 network is achieved which is 0.47% degraded from software accuracy.
- 29 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 71  (4) , 1869-1873
Split WL 6T SRAM-Based Bit Serial Computing-in-Memory Macro With High Signal Margin and High Throughput
This paper proposes a split WL 6T SRAM computing-in-memory (CIM) macro for high signal margin and high throughput bit-serial multiply-accumulate (MAC) operation with 8-b input, 8-b weight, and 20-b output. The proposed architecture improves signal margin with input flipping WL control that limits the maximum number of turned-on WLs, throughput with a dual BL sensing scheme and pipelining, and energy efficiency with an input-aware trip point-based ADC and supply voltage adjustment of a near memory processor (NMP). The proposed architecture is fabricated in 65nm technology and achieves 152.32 bit-wise TOPS/W and 20.69 bit-wise TOPS/mm2. In addition, 91.23% inference accuracy at the CIFAR-10 image classification dataset with the ResNET-20 network is achieved which is 0.47% degraded from software accuracy.
- 15 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 71  (4) , 1824-1828
A Charge-Domain 4T2C eDRAM Compute-in-Memory Macro With Enhanced Variation Tolerance and Low-Overhead Data Conversion Schemes
In this brief, a novel charge-domain 4T2C eDRAM-CIM macro is proposed that has three key features: 1) a novel 4T2C eDRAM cell with an enhanced PVT variation tolerance that resolves the limitations of previous eDRAM-CIM macros such as current domain operation, large bit-cell size, cell leakage, and low energy- and area-efficiency, resulting in high linearity (R2 = 0.9998) and 76.8% reduction in$3\sigma $ PVT variation, 2) a quarter-ADC-reduction scheme with an offset-calibration comparator that reduces the number of ADC by 73% while improving the accuracy drop by 7.82%, and 3) an array-embedded DAC that reduces the area overhead by 64.2% compared to current-based DAC. The proposed 4T2C eDRAM-CIM macro is fabricated in 65nm LP technology and achieves 43.02- to 49.20-TOPS/W and 2.4-TOPS/mm 2 when 4b$\times 4\text{b}$ MAC operation is performed with 250MHz. In addition, an 90.03% accuracy at the CIFAR-10 dataset with the ResNet-20 network is achieved.- 15 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 71  (4) , 1824-1828
A Charge-Domain 4T2C eDRAM Compute-in-Memory Macro With Enhanced Variation Tolerance and Low-Overhead Data Conversion Schemes
In this brief, a novel charge-domain 4T2C eDRAM-CIM macro is proposed that has three key features: 1) a novel 4T2C eDRAM cell with an enhanced PVT variation tolerance that resolves the limitations of previous eDRAM-CIM macros such as current domain operation, large bit-cell size, cell leakage, and low energy- and area-efficiency, resulting in high linearity (R2 = 0.9998) and 76.8% reduction in$3\sigma $ PVT variation, 2) a quarter-ADC-reduction scheme with an offset-calibration comparator that reduces the number of ADC by 73% while improving the accuracy drop by 7.82%, and 3) an array-embedded DAC that reduces the area overhead by 64.2% compared to current-based DAC. The proposed 4T2C eDRAM-CIM macro is fabricated in 65nm LP technology and achieves 43.02- to 49.20-TOPS/W and 2.4-TOPS/mm 2 when 4b$\times 4\text{b}$ MAC operation is performed with 250MHz. In addition, an 90.03% accuracy at the CIFAR-10 dataset with the ResNet-20 network is achieved.- 2 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 71  (1) , 274-286
Ferroelectric FET Nonvolatile Sense-Amplifier-Based Flip-Flops for Low Voltage Operation
Nonvolatile processors (NVPs) are promising for energy-constrained internet-of-things applications in which frequent switch to standby mode occurs due to their fast and energy-efficient backup and restore operations of locally embedded nonvolatile flip-flops (NV-FFs) with zero leakage current. In addition, the most effective method to reduce dynamic energy consumption is to lower the supply voltage ( V $_{DD}$ ). The sense-amplifier-based flip-flop (SAFF) is considered a suitable choice for the low V $_{DD}$ operation, since it does not suffer from setup time degradation as V $_{DD}$ lowers. This study presents two ferroelectric FET (FeFET) nonvolatile SAFFs (FeFET NV-SAFF-1 and -2) that exhibit significantly low sequencing overhead (setup time $+$ clock-to-Q time) at low V $_{DD}$ and consume low operating energy in the range of femto joules with compact layout area. The FeFET NV-SAFF-1 can operate robustly at low V $_{DD}$ even with a low resistance ratio. The FeFET NV-SAFF-2 has no area overhead and achieves the best power-performance-area at low V $_{DD}$ among state-of-the-art and proposed FeFET NV-FFs.
- 2 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 71  (1) , 274-286
Ferroelectric FET Nonvolatile Sense-Amplifier-Based Flip-Flops for Low Voltage Operation
Nonvolatile processors (NVPs) are promising for energy-constrained internet-of-things applications in which frequent switch to standby mode occurs due to their fast and energy-efficient backup and restore operations of locally embedded nonvolatile flip-flops (NV-FFs) with zero leakage current. In addition, the most effective method to reduce dynamic energy consumption is to lower the supply voltage ( V $_{DD}$ ). The sense-amplifier-based flip-flop (SAFF) is considered a suitable choice for the low V $_{DD}$ operation, since it does not suffer from setup time degradation as V $_{DD}$ lowers. This study presents two ferroelectric FET (FeFET) nonvolatile SAFFs (FeFET NV-SAFF-1 and -2) that exhibit significantly low sequencing overhead (setup time $+$ clock-to-Q time) at low V $_{DD}$ and consume low operating energy in the range of femto joules with compact layout area. The FeFET NV-SAFF-1 can operate robustly at low V $_{DD}$ even with a low resistance ratio. The FeFET NV-SAFF-2 has no area overhead and achieves the best power-performance-area at low V $_{DD}$ among state-of-the-art and proposed FeFET NV-FFs.
- 18 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 58  (7) , 1860-1870
Dual-Mode Operations of Self-Rectifying Ferroelectric Tunnel Junction Crosspoint Array for High-Density Integration of IoT Devices
This study proposes a self-rectifying ferroelectric tunnel junction (SR-FTJ) crosspoint array to satisfy the stringent size requirements of the Internet-of-Things devices. Each cell in the SR-FTJ crosspoint array consists of two SR-FTJs stacked vertically, resulting in ultrahigh density. The SR-FTJ crosspoint array can operate as: 1) ternary content-addressable memory (TCAM) or 2) binary content addressable memory (BCAM) or physically unclonable function (PUF) in the dual-mode operation. In the dual-mode operation, the amount of the current flowing through the SR-FTJs remains the same, resulting in a stable PUF response regardless of the BCAM data. The dual-mode operation of the SR-FTJ crosspoint array is experimentally verified by 4-in wafer-level demonstrations. HSPICE simulation results using the industrial-compatible 180-nm technology with the SR-FTJ model reflecting measured characteristics show that the SR-FTJ crosspoint array achieves the lowest search energy (2.05 fJ/search/bit) and the highest randomness (Hamming weight of 0.5000) among the previous content addressable memories (CAMs) and PUFs. In addition, the SR-FTJ crosspoint array reduces area by $>$ 84.2% compared to the previous structures that implement individual CAM and PUF.
- 18 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 58  (7) , 1860-1870
Dual-Mode Operations of Self-Rectifying Ferroelectric Tunnel Junction Crosspoint Array for High-Density Integration of IoT Devices
This study proposes a self-rectifying ferroelectric tunnel junction (SR-FTJ) crosspoint array to satisfy the stringent size requirements of the Internet-of-Things devices. Each cell in the SR-FTJ crosspoint array consists of two SR-FTJs stacked vertically, resulting in ultrahigh density. The SR-FTJ crosspoint array can operate as: 1) ternary content-addressable memory (TCAM) or 2) binary content addressable memory (BCAM) or physically unclonable function (PUF) in the dual-mode operation. In the dual-mode operation, the amount of the current flowing through the SR-FTJs remains the same, resulting in a stable PUF response regardless of the BCAM data. The dual-mode operation of the SR-FTJ crosspoint array is experimentally verified by 4-in wafer-level demonstrations. HSPICE simulation results using the industrial-compatible 180-nm technology with the SR-FTJ model reflecting measured characteristics show that the SR-FTJ crosspoint array achieves the lowest search energy (2.05 fJ/search/bit) and the highest randomness (Hamming weight of 0.5000) among the previous content addressable memories (CAMs) and PUFs. In addition, the SR-FTJ crosspoint array reduces area by $>$ 84.2% compared to the previous structures that implement individual CAM and PUF.