Se Keon Kim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Se Keon Kim has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Seong-Ook Jung
Yonsei University
8 shared publications - Dong Han Ko
School of Electrical and Electronic Engineering, Yonsei University, Seoul, South Korea
6 shared publications - Sehee Lim
School of Electrical and Electronic Engineering, Yonsei University, Seoul, South Korea
5 shared publications - Tae Woo Oh
School of Electrical and Electronic Engineering, Yonsei University, Seoul, South Korea
4 shared publications Dongwook Seo
Foundry Division, Samsung Electronics Company Ltd., Gyeonggi, South Korea
2 shared publications- Giseok Kim
School of Electrical and Electronic Engineering, Yonsei University, Seoul, South Korea
2 shared publications
Latest Publications
- 27 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. PP (00189200) , 1-12
Dual-Mode Inverter-Based Write Termination Scheme for Energy- and Area-Efficient Write Operation in 28-nm 1T1MTJ STT-MRAM
Spin-transfer torque magnetic random access memory (STT-MRAM) is a promising non-volatile memory, but its write operation requires a large static current, leading to high write power. Resistance-monitoring write termination (RM-WT) schemes were introduced to reduce write power, but they suffer from several limitations: 1) the sensing circuit (SC) used in previous schemes has limited effective input voltage, degrading the robustness of WT; 2) the prior schemes cause severe area overhead due to the additional WT circuits besides sense amplifier (SA); and 3) the previous schemes cannot support write 0 termination, limiting write power reduction. This article proposes a dual-mode inverter-based write-termination (DMI-WT) circuit that resolves these limitations. In the proposed scheme, a single-ended inverter-based SC (INV-SC) is used, which doubles the effective input voltage without area overhead. In addition, self-referenced offset cancel (OC) is used, which enables robust WT and SA operation. DMI-WT enables WT operation for both write 0 and write 1 operation while simultaneously serving as an SA, thereby reducing the write power and removing the area overhead caused by WT circuits. A prototype chip fabricated in 28-nm CMOS technology with a 256-kb STT-MRAM array shows that DMI-WT achieves up to $6.39{\times }$ area overhead reduction, $7.5{\times }$ lower write power per bit at a 20-ns write access time, $1.27{\times }$ faster read access time, and $1.41{\times }$ lower read power compared with previous WT circuits using STT-MRAM.
- 27 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. PP (00189200) , 1-12
Dual-Mode Inverter-Based Write Termination Scheme for Energy- and Area-Efficient Write Operation in 28-nm 1T1MTJ STT-MRAM
Spin-transfer torque magnetic random access memory (STT-MRAM) is a promising non-volatile memory, but its write operation requires a large static current, leading to high write power. Resistance-monitoring write termination (RM-WT) schemes were introduced to reduce write power, but they suffer from several limitations: 1) the sensing circuit (SC) used in previous schemes has limited effective input voltage, degrading the robustness of WT; 2) the prior schemes cause severe area overhead due to the additional WT circuits besides sense amplifier (SA); and 3) the previous schemes cannot support write 0 termination, limiting write power reduction. This article proposes a dual-mode inverter-based write-termination (DMI-WT) circuit that resolves these limitations. In the proposed scheme, a single-ended inverter-based SC (INV-SC) is used, which doubles the effective input voltage without area overhead. In addition, self-referenced offset cancel (OC) is used, which enables robust WT and SA operation. DMI-WT enables WT operation for both write 0 and write 1 operation while simultaneously serving as an SA, thereby reducing the write power and removing the area overhead caused by WT circuits. A prototype chip fabricated in 28-nm CMOS technology with a 256-kb STT-MRAM array shows that DMI-WT achieves up to $6.39{\times }$ area overhead reduction, $7.5{\times }$ lower write power per bit at a 20-ns write access time, $1.27{\times }$ faster read access time, and $1.41{\times }$ lower read power compared with previous WT circuits using STT-MRAM.
- 1 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (3) , 1228-1239
A High-Density Low-Leakage and Low-Power Fully Voltage-Stacked SRAM for IoT Application
The general approach to suppress leakage in static random access memory (SRAM) is to use a low voltage ( $V_{\text {L}}$ ), generated by a low-dropout regulator (LDO), as the cell supply voltage (CVDD) of SRAM array in the standby mode. However, the effectiveness of lowering CVDD is constrained by the area and power overhead introduced by the LDO, as well as the additional latency and power consumption incurred during mode switching. This work presents a fully voltage-stacked (FVS) SRAM that reduces leakage power with internally generated intermediate voltage ( $V_{\text {MID}}$ ) by stacking SRAM arrays. The FVS SRAM consists of a foundry high-density (HD) cell and a pMOS pass-gate (PG) cell having the same metal pattern and size as the HD cell, ensuring compatibility across various process nodes. In addition, the FVS SRAM reduces minimum operating voltage and access energy by the intermediate cell voltage (ICV) assist technique and charge-sharing-based precharge, respectively. The silicon measurement results from a 14-nm FinFET test chip demonstrate that the FVS SRAM achieves a leakage power of 5.34 pW/bit and an access energy of 24.6 fJ/bit at ${V_{\text {MIN}}}{=}0.5$ V. Compared to conventional non-stacked SRAM, the FVS SRAM exhibits 29%–59% and 10%–21% reduction in leakage power and access energy across VDD ${=}0.6$ –0.8 V.
- 1 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (3) , 1228-1239
A High-Density Low-Leakage and Low-Power Fully Voltage-Stacked SRAM for IoT Application
The general approach to suppress leakage in static random access memory (SRAM) is to use a low voltage ( $V_{\text {L}}$ ), generated by a low-dropout regulator (LDO), as the cell supply voltage (CVDD) of SRAM array in the standby mode. However, the effectiveness of lowering CVDD is constrained by the area and power overhead introduced by the LDO, as well as the additional latency and power consumption incurred during mode switching. This work presents a fully voltage-stacked (FVS) SRAM that reduces leakage power with internally generated intermediate voltage ( $V_{\text {MID}}$ ) by stacking SRAM arrays. The FVS SRAM consists of a foundry high-density (HD) cell and a pMOS pass-gate (PG) cell having the same metal pattern and size as the HD cell, ensuring compatibility across various process nodes. In addition, the FVS SRAM reduces minimum operating voltage and access energy by the intermediate cell voltage (ICV) assist technique and charge-sharing-based precharge, respectively. The silicon measurement results from a 14-nm FinFET test chip demonstrate that the FVS SRAM achieves a leakage power of 5.34 pW/bit and an access energy of 24.6 fJ/bit at ${V_{\text {MIN}}}{=}0.5$ V. Compared to conventional non-stacked SRAM, the FVS SRAM exhibits 29%–59% and 10%–21% reduction in leakage power and access energy across VDD ${=}0.6$ –0.8 V.
- 25 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (2) , 724-735
A 14 nm SRAM Using NMOS Header Assist Cell for Improved Write Ability and Reduced Cell Retention Leakage With Minimal Power Overhead
This article presents an NMOS header assist cell (NHAC) that lowers static random access memory (SRAM) minimum operating voltage ( $V_{\text {MIN}}$ ) with minimal power overhead for low-power applications, even in the case of increased interconnect resistance ( $R_{\text {INT}}$ ) with technology scaling. The proposed NHAC, featuring a Bitcell-compatible layout, is inserted between cell arrays to supply power by dividing cell-power (CVDD) into sub-arrays without additional dummy cells or white space. NHAC improves write ability even in high $R_{\text {INT}}$ cases, thanks to the continuous self-collapse of the CVDD voltage by supplying cell power through NMOS during write operations. The NMOS header in NHAC prevents excessive CVDD voltage collapse, thus ensuring the dynamic data retention stability of column half-selected cells (CHSCs). Additionally, by enabling all NHACs in sleep mode, the CVDD voltage can be clamped below the supply voltage, thereby reducing bitcell retention leakage without additional area costs. SRAM macros with additional resistors were fabricated using a 14 nm FinFET process to measure the impact of $R_{\text {INT}}$ on the write assist circuits. NHAC achieves a $V_{\text {MIN}}$ improvement of 210 mV with 4% power overhead, even in the high $R_{\text {INT}}$ case. In sleep mode, NHAC reduces bitcell retention leakage by 25% at 0.65 V and up to 61% at 1 V. NHAC demonstrates improved write $V_{\text {MIN}}$ similar to transient voltage collapse (TVC) write assist. Additionally, it achieves low-power overhead similar to self-induced voltage collapse (SIC) write assist.
- 25 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (2) , 724-735
A 14 nm SRAM Using NMOS Header Assist Cell for Improved Write Ability and Reduced Cell Retention Leakage With Minimal Power Overhead
This article presents an NMOS header assist cell (NHAC) that lowers static random access memory (SRAM) minimum operating voltage ( $V_{\text {MIN}}$ ) with minimal power overhead for low-power applications, even in the case of increased interconnect resistance ( $R_{\text {INT}}$ ) with technology scaling. The proposed NHAC, featuring a Bitcell-compatible layout, is inserted between cell arrays to supply power by dividing cell-power (CVDD) into sub-arrays without additional dummy cells or white space. NHAC improves write ability even in high $R_{\text {INT}}$ cases, thanks to the continuous self-collapse of the CVDD voltage by supplying cell power through NMOS during write operations. The NMOS header in NHAC prevents excessive CVDD voltage collapse, thus ensuring the dynamic data retention stability of column half-selected cells (CHSCs). Additionally, by enabling all NHACs in sleep mode, the CVDD voltage can be clamped below the supply voltage, thereby reducing bitcell retention leakage without additional area costs. SRAM macros with additional resistors were fabricated using a 14 nm FinFET process to measure the impact of $R_{\text {INT}}$ on the write assist circuits. NHAC achieves a $V_{\text {MIN}}$ improvement of 210 mV with 4% power overhead, even in the high $R_{\text {INT}}$ case. In sleep mode, NHAC reduces bitcell retention leakage by 25% at 0.65 V and up to 61% at 1 V. NHAC demonstrates improved write $V_{\text {MIN}}$ similar to transient voltage collapse (TVC) write assist. Additionally, it achieves low-power overhead similar to self-induced voltage collapse (SIC) write assist.
- 10 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Internet of Things Journal
- Vol. 11 (16) , 27676-27686
Design of Physically Unclonable Function Using Ferroelectric FET With Auto Write-Back Technique for Resource-Limited IoT Security
Physically unclonable function (PUF) is a lightweight encryption technique that generates random digital keys (responses) using intrinsic process variations of devices, which is a promising solution for Internet of Things (IoT) security due to its compatibility with constrained resources. Recent attempts to adopt nonvolatile memory (NVM) into PUFs have enhanced stability through a write-back technique that maintains consistent responses from the enrollment phase even under wide environmental variations by storing the response in the NVM device. However, the stability of the previous NVM PUFs is limited by the low on/off ratio of the NVMs. In addition, the circuit required to implement the write-back technique poses challenges of increased area and energy consumption. Considering the hardware limitations and power constraints of IoT devices, this paper proposes a ferroelectric field-effect transistor (FeFET) PUF as a suitable security solution. The high on/off ratio of FeFET and the proposed auto write-back technique that does not require additional circuitry realize the stability improvement (a bit error rate of <0.0001%) under wide environmental variations without incurring area and energy overheads. The negligible off current of FeFET prevents static power consumption, which leads to the lowest energy consumption of 6.70e-15 J during the response generation of the FeFET PUF. In addition, the compact PUF cell composed of two FeFETs achieves a high density of 87.37 F2.
- 10 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Internet of Things Journal
- Vol. 11 (16) , 27676-27686
Design of Physically Unclonable Function Using Ferroelectric FET With Auto Write-Back Technique for Resource-Limited IoT Security
Physically unclonable function (PUF) is a lightweight encryption technique that generates random digital keys (responses) using intrinsic process variations of devices, which is a promising solution for Internet of Things (IoT) security due to its compatibility with constrained resources. Recent attempts to adopt nonvolatile memory (NVM) into PUFs have enhanced stability through a write-back technique that maintains consistent responses from the enrollment phase even under wide environmental variations by storing the response in the NVM device. However, the stability of the previous NVM PUFs is limited by the low on/off ratio of the NVMs. In addition, the circuit required to implement the write-back technique poses challenges of increased area and energy consumption. Considering the hardware limitations and power constraints of IoT devices, this paper proposes a ferroelectric field-effect transistor (FeFET) PUF as a suitable security solution. The high on/off ratio of FeFET and the proposed auto write-back technique that does not require additional circuitry realize the stability improvement (a bit error rate of <0.0001%) under wide environmental variations without incurring area and energy overheads. The negligible off current of FeFET prevents static power consumption, which leads to the lowest energy consumption of 6.70e-15 J during the response generation of the FeFET PUF. In addition, the compact PUF cell composed of two FeFETs achieves a high density of 87.37 F2.
- 2 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 71 (1) , 274-286
Ferroelectric FET Nonvolatile Sense-Amplifier-Based Flip-Flops for Low Voltage Operation
Nonvolatile processors (NVPs) are promising for energy-constrained internet-of-things applications in which frequent switch to standby mode occurs due to their fast and energy-efficient backup and restore operations of locally embedded nonvolatile flip-flops (NV-FFs) with zero leakage current. In addition, the most effective method to reduce dynamic energy consumption is to lower the supply voltage ( V $_{DD}$ ). The sense-amplifier-based flip-flop (SAFF) is considered a suitable choice for the low V $_{DD}$ operation, since it does not suffer from setup time degradation as V $_{DD}$ lowers. This study presents two ferroelectric FET (FeFET) nonvolatile SAFFs (FeFET NV-SAFF-1 and -2) that exhibit significantly low sequencing overhead (setup time $+$ clock-to-Q time) at low V $_{DD}$ and consume low operating energy in the range of femto joules with compact layout area. The FeFET NV-SAFF-1 can operate robustly at low V $_{DD}$ even with a low resistance ratio. The FeFET NV-SAFF-2 has no area overhead and achieves the best power-performance-area at low V $_{DD}$ among state-of-the-art and proposed FeFET NV-FFs.
- 2 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 71 (1) , 274-286
Ferroelectric FET Nonvolatile Sense-Amplifier-Based Flip-Flops for Low Voltage Operation
Nonvolatile processors (NVPs) are promising for energy-constrained internet-of-things applications in which frequent switch to standby mode occurs due to their fast and energy-efficient backup and restore operations of locally embedded nonvolatile flip-flops (NV-FFs) with zero leakage current. In addition, the most effective method to reduce dynamic energy consumption is to lower the supply voltage ( V $_{DD}$ ). The sense-amplifier-based flip-flop (SAFF) is considered a suitable choice for the low V $_{DD}$ operation, since it does not suffer from setup time degradation as V $_{DD}$ lowers. This study presents two ferroelectric FET (FeFET) nonvolatile SAFFs (FeFET NV-SAFF-1 and -2) that exhibit significantly low sequencing overhead (setup time $+$ clock-to-Q time) at low V $_{DD}$ and consume low operating energy in the range of femto joules with compact layout area. The FeFET NV-SAFF-1 can operate robustly at low V $_{DD}$ even with a low resistance ratio. The FeFET NV-SAFF-2 has no area overhead and achieves the best power-performance-area at low V $_{DD}$ among state-of-the-art and proposed FeFET NV-FFs.
- 17 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 70 (2) , 806-818
Cross-Coupled Ferroelectric FET-Based Ternary Content Addressable Memory With Energy-Efficient Match Line Scheme
Fast communication between networking devices increases the importance of the ternary content addressable memory (TCAM). The demands for low energy in networking devices have accelerated the research on nonvolatile TCAMs that store data without the power supply. Recently, ferroelectric field-effect transistors (FeFETs), nonvolatile three-terminal devices with a high on/off ratio, have been adopted for TCAMs. Although the previous FeFET TCAMs consume low write energy with a significantly compact TCAM cell area, they suffer from write problems: 1) the write scheme cannot afford the saturated polarization switching in FeFETs and 2) the states stored in the unselected TCAM cells are changed during the write operation. In addition, search yield is deteriorated by wide process variations of FeFETs. This paper proposes a novel FeFET TCAM that is free from the write problems of the previous FeFET TCAMs and tolerant to process variations. This paper also proposes a novel match line scheme to improve search energy and time by reducing match line capacitance and the amount of discharged voltage in the match evaluation phase. Industrial-compatible 28 nm technology-based simulation results with the Preisach FeFET model show that the proposed FeFET TCAM achieves the highest search yield.
- 17 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 70 (2) , 806-818
Cross-Coupled Ferroelectric FET-Based Ternary Content Addressable Memory With Energy-Efficient Match Line Scheme
Fast communication between networking devices increases the importance of the ternary content addressable memory (TCAM). The demands for low energy in networking devices have accelerated the research on nonvolatile TCAMs that store data without the power supply. Recently, ferroelectric field-effect transistors (FeFETs), nonvolatile three-terminal devices with a high on/off ratio, have been adopted for TCAMs. Although the previous FeFET TCAMs consume low write energy with a significantly compact TCAM cell area, they suffer from write problems: 1) the write scheme cannot afford the saturated polarization switching in FeFETs and 2) the states stored in the unselected TCAM cells are changed during the write operation. In addition, search yield is deteriorated by wide process variations of FeFETs. This paper proposes a novel FeFET TCAM that is free from the write problems of the previous FeFET TCAMs and tolerant to process variations. This paper also proposes a novel match line scheme to improve search energy and time by reducing match line capacitance and the amount of discharged voltage in the match evaluation phase. Industrial-compatible 28 nm technology-based simulation results with the Preisach FeFET model show that the proposed FeFET TCAM achieves the highest search yield.
- Open Access
- 10 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 127895-127905
Comparative Analysis and Energy-Efficient Write Scheme of Ferroelectric FET-Based Memory Cells
The ferroelectric field-effect transistor (FeFET) is one of the most promising candidates for emerging nonvolatile memory devices owing to its low write energy and high $I_{\mathrm {ON}}/I_{\mathrm {OFF}}$ ratio. For FeFET applications as nonvolatile memory devices, 1FeFET, 1T-1FeFET, 2T-1FeFET, and 3T-1FeFET cells have been proposed. The 1FeFET cell exhibits the highest density but suffers from write disturbance. Although the 1T-1FeFET and 2T-1FeFET cells resolve the write disturbance, they use a write scheme with a negative write voltage ( $V_{\mathrm {W}}$ ), which requires voltage swings of many control signals, leading to a significantly high write energy consumption. The 3T-1FeFET cell uses a write scheme without a negative $V_{\mathrm {W}}$ ; however, it exhibits the largest area overhead. Although the 1T-1FeFET cell resolves the write disturbance with a small area overhead; however, it exhibits high write energy consumption because of the use of a negative $V_{\mathrm {W}}$ . In this paper, to significantly reduce the write energy consumption, we propose a less control signal swing (LCSS) write scheme without using a negative $V_{\mathrm {W}}$ . Simulation results indicate that the worst, average, and best cases of the proposed LCSS write scheme can achieve 35%, 66%, and 96% lower write energy consumption, respectively, than the write scheme with a negative $V_{\mathrm {W}}$ in the 1T-1FeFET cell. We also identify the available sensing schemes for each FeFET cell in the read operation according to the FeFET threshold voltage distribution.
- 10 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 127895-127905
Open AccessComparative Analysis and Energy-Efficient Write Scheme of Ferroelectric FET-Based Memory Cells
The ferroelectric field-effect transistor (FeFET) is one of the most promising candidates for emerging nonvolatile memory devices owing to its low write energy and high $I_{\mathrm {ON}}/I_{\mathrm {OFF}}$ ratio. For FeFET applications as nonvolatile memory devices, 1FeFET, 1T-1FeFET, 2T-1FeFET, and 3T-1FeFET cells have been proposed. The 1FeFET cell exhibits the highest density but suffers from write disturbance. Although the 1T-1FeFET and 2T-1FeFET cells resolve the write disturbance, they use a write scheme with a negative write voltage ( $V_{\mathrm {W}}$ ), which requires voltage swings of many control signals, leading to a significantly high write energy consumption. The 3T-1FeFET cell uses a write scheme without a negative $V_{\mathrm {W}}$ ; however, it exhibits the largest area overhead. Although the 1T-1FeFET cell resolves the write disturbance with a small area overhead; however, it exhibits high write energy consumption because of the use of a negative $V_{\mathrm {W}}$ . In this paper, to significantly reduce the write energy consumption, we propose a less control signal swing (LCSS) write scheme without using a negative $V_{\mathrm {W}}$ . Simulation results indicate that the worst, average, and best cases of the proposed LCSS write scheme can achieve 35%, 66%, and 96% lower write energy consumption, respectively, than the write scheme with a negative $V_{\mathrm {W}}$ in the 1T-1FeFET cell. We also identify the available sensing schemes for each FeFET cell in the read operation according to the FeFET threshold voltage distribution.
- Open Access
- 24 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 35549-35561
High-Performance and Area-Efficient Ferroelectric FET-Based Nonvolatile Flip-Flops
Recently, nonvolatile systems with nonvolatile flip-flops (NVFFs) have gained prominence for their energy efficiency in energy-harvesting devices and battery-operated Internet of Things applications. They are normally-off instantly-on, and thus, can save energy effectively owing to their zero standby power consumption. An NVFF stores the computing state in nonvolatile memories (NVMs) when the power is off. A ferroelectric field-effect transistor (FeFET) is one of the most promising NVMs owing to its high I on /I off ratio and low write power. Three FeFET-based NVFFs (previous FeFET-out NVFF-1/-2 and FeFET-in NVFF) were recently proposed to improve the area, power, and speed; however, they still have their own problems. Previous FeFET-out NVFF-1 has large area overhead and previous FeFET-out NVFF-2 does not properly perform restore operation. Previous FeFET-in NVFF has a long clock-to-Q delay and high operating energy. This paper introduces two novel FeFET-based NVFFs (proposed FeFET-out and -in NVFFs). Proposed FeFET-out NVFF reduces the large area overhead of previous FeFET-out NVFF-1 and corrects the malfunction in the restore operation of previous FeFET-out NVFF-2. Proposed FeFET-in NVFF achieves a better clock-to-Q delay, operating energy, and area than the previous FeFET-in NVFF. Monte Carlo simulations based on an industry-compatible 10-nm FinFET model are performed for a comparative analysis. Proposed FeFET-out NVFF achieves 17.6% smaller area with slightly higher (6.3%) operating energy and only 0.8% slower clock-to-Q delay than previous FeFET-out NVFF-1. Proposed FeFET-in NVFF achieves 18.9% shorter clock-to-Q and 3.0% smaller operating energy with 8.7% smaller area than the previous FeFET-in NVFF.
- 24 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 35549-35561
Open AccessHigh-Performance and Area-Efficient Ferroelectric FET-Based Nonvolatile Flip-Flops
Recently, nonvolatile systems with nonvolatile flip-flops (NVFFs) have gained prominence for their energy efficiency in energy-harvesting devices and battery-operated Internet of Things applications. They are normally-off instantly-on, and thus, can save energy effectively owing to their zero standby power consumption. An NVFF stores the computing state in nonvolatile memories (NVMs) when the power is off. A ferroelectric field-effect transistor (FeFET) is one of the most promising NVMs owing to its high I on /I off ratio and low write power. Three FeFET-based NVFFs (previous FeFET-out NVFF-1/-2 and FeFET-in NVFF) were recently proposed to improve the area, power, and speed; however, they still have their own problems. Previous FeFET-out NVFF-1 has large area overhead and previous FeFET-out NVFF-2 does not properly perform restore operation. Previous FeFET-in NVFF has a long clock-to-Q delay and high operating energy. This paper introduces two novel FeFET-based NVFFs (proposed FeFET-out and -in NVFFs). Proposed FeFET-out NVFF reduces the large area overhead of previous FeFET-out NVFF-1 and corrects the malfunction in the restore operation of previous FeFET-out NVFF-2. Proposed FeFET-in NVFF achieves a better clock-to-Q delay, operating energy, and area than the previous FeFET-in NVFF. Monte Carlo simulations based on an industry-compatible 10-nm FinFET model are performed for a comparative analysis. Proposed FeFET-out NVFF achieves 17.6% smaller area with slightly higher (6.3%) operating energy and only 0.8% slower clock-to-Q delay than previous FeFET-out NVFF-1. Proposed FeFET-in NVFF achieves 18.9% shorter clock-to-Q and 3.0% smaller operating energy with 8.7% smaller area than the previous FeFET-in NVFF.