C. R. Neeraj
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
C. R. Neeraj has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Sudheesh Thiyyakkandi
Indian Institute of Technology Palakkad
4 shared publications - Alpha Lukose
MA College of Engineering
1 shared publication - K. T. Saikumar
Indian Institute of Technology Palakkad
1 shared publication - Michael McVay
Professor, Dept. of Civil and Coastal Engineering, Univ. of Florida, 365 Weil Hall, Gainesville, FL 32611
1 shared publication - P. Shankar
Department of Civil Engineering, Indian Institute of Technology, Kerala, India
1 shared publication
Latest Publications
- 29 November 2022
- Published by Springer Nature
- p. 249-259
Influence of Soil Cover on Lateral Response of Rock-Socketed Piles
- 29 November 2022
- Published by Springer Nature
- p. 249-259
Influence of Soil Cover on Lateral Response of Rock-Socketed Piles
- 1 June 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 148 (6) , 04022030
Full-Scale Axial Load Response of Jetted and Grouted Precast Piles in Cohesionless Soils
Jetted and grouted precast piles (JGPPs) are a newly developed urban-friendly deep foundation technique that employs water jetting for pile penetration and pressure grouting to enhance the axial and torsional resistance of precast piles. Previous experimental studies of JGPPs in a large test chamber setup have revealed that they can withstand very high axial loads; however, validation of the same in a typical field scenario was needed. This paper presents the pioneering study of the full-scale axial response of JGPPs in cohesionless soil condition. The study showed that JGPPs exhibit high skin and tip resistances under axial top-down loading. The paper also proposes a direct method to predict the ultimate skin resistance of JGPPs using the pressuremeter test results. The experimental results were compared with the values estimated using both the proposed and existing methods.
- 1 June 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 148 (6) , 04022030
Full-Scale Axial Load Response of Jetted and Grouted Precast Piles in Cohesionless Soils
Jetted and grouted precast piles (JGPPs) are a newly developed urban-friendly deep foundation technique that employs water jetting for pile penetration and pressure grouting to enhance the axial and torsional resistance of precast piles. Previous experimental studies of JGPPs in a large test chamber setup have revealed that they can withstand very high axial loads; however, validation of the same in a typical field scenario was needed. This paper presents the pioneering study of the full-scale axial response of JGPPs in cohesionless soil condition. The study showed that JGPPs exhibit high skin and tip resistances under axial top-down loading. The paper also proposes a direct method to predict the ultimate skin resistance of JGPPs using the pressuremeter test results. The experimental results were compared with the values estimated using both the proposed and existing methods.
- 20 December 2021
- Published by Springer Nature in Innovative Infrastructure Solutions
- Vol. 7 (1) , 1-8
Active earth pressure on retaining walls with sloping backfill considering arching effect under rotation about base
- 20 December 2021
- Published by Springer Nature in Innovative Infrastructure Solutions
- Vol. 7 (1) , 1-8
Active earth pressure on retaining walls with sloping backfill considering arching effect under rotation about base
- Open Access
- 1 December 2021
- Published by Emerald Publishing in Geotechnical Research
- Vol. 8 (4) , 117-129
Factor of safety of pile-stabilised slopes: an algorithm incorporating soil-arching effect
The current practice of factor of safety computation of pile-stabilised slopes depends substantially on either the extension of methods for normal slopes with the pile-contribution introduced as an additional term or finite-element modelling. Extending conventional methods to analyse pile-stabilised slopes fails to capture the key mechanisms like soil arching, gradual transfer of resistance offered by the pile through the slope, change in slip surface due to introduction of piles and so on. In this paper, a new algorithm is proposed to compute the factor of safety of pile-stabilised slopes, in which the Morgenstern–Price method is modified to incorporate the effect of a pile. The resistance offered by the pile is obtained using a pressure-based method which considers the soil-arching effect in horizontal and vertical directions. The gradual propagation of this resistance offered by the pile is incorporated through an iterative procedure, unlike the conventional methods. The algorithm considers the change in slip surface due to the introduction of the pile. The factor of safety values computed using the proposed algorithm were found to be in close agreement with that obtained from finite-element modelling. Moreover, a simple technique to determine the optimal location of stabilising piles and pile-spacing is also presented.
- 1 December 2021
- Published by Emerald Publishing in Geotechnical Research
- Vol. 8 (4) , 117-129
Open AccessFactor of safety of pile-stabilised slopes: an algorithm incorporating soil-arching effect
The current practice of factor of safety computation of pile-stabilised slopes depends substantially on either the extension of methods for normal slopes with the pile-contribution introduced as an additional term or finite-element modelling. Extending conventional methods to analyse pile-stabilised slopes fails to capture the key mechanisms like soil arching, gradual transfer of resistance offered by the pile through the slope, change in slip surface due to introduction of piles and so on. In this paper, a new algorithm is proposed to compute the factor of safety of pile-stabilised slopes, in which the Morgenstern–Price method is modified to incorporate the effect of a pile. The resistance offered by the pile is obtained using a pressure-based method which considers the soil-arching effect in horizontal and vertical directions. The gradual propagation of this resistance offered by the pile is incorporated through an iterative procedure, unlike the conventional methods. The algorithm considers the change in slip surface due to the introduction of the pile. The factor of safety values computed using the proposed algorithm were found to be in close agreement with that obtained from finite-element modelling. Moreover, a simple technique to determine the optimal location of stabilising piles and pile-spacing is also presented.