Viviane Bouyer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Viviane Bouyer has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- Christophe Journeau
CEA, DES, IRESNE, DTN, Severe Accident Experimental Laboratory
5 shared publications Arthur Denoix
4 shared publications- Michael Johnson
Commissariat à l'Énergie Atomique et aux Énergies Alternatives (CEA), Cadarache, DES, IRESNE, DTN, SMTA, LEAG Saint‐Paul‐lez‐Durance France
2 shared publications Antonin Bouland
1 shared publication- Arthur Denoix1 shared publication
- Benjamin Turquais
CEA, DES, IRESNE, DTN 1 , Cadarache, F-13108 Saint-Paul-Lez-Durance, France
1 shared publication
Latest Publications
- Open Access
- 3 October 2026
- Published by Elsevier in Annals of Nuclear Energy
- Vol. 242
Experimental investigation of corium top-flooding with sustained induction heating and MCCI
- 3 October 2026
- Published by Elsevier in Annals of Nuclear Energy
- Vol. 242
Open AccessExperimental investigation of corium top-flooding with sustained induction heating and MCCI
- Open Access
- 4 September 2026
- Published by Elsevier in SSRN Electronic Journal
Fuel debris prototype fabrication and cutting in view of determining airborne release fraction for Fukushima Daiichi fuel debris retrieval
Estimating the Airborne Release Fraction (ARF) during fuel debris (FD) retrieval is important for the safe decommissioning of the Fukushima Daiichi Nuclear Power Plant (1F) because it supports exposure assessment and the design of mitigation measures. Dust generation during dry mechanical cutting depends not only on operating conditions but also strongly on the properties of the cut material, including size, geometry, mechanical behavior and multiphase heterogeneity. Therefore, representative simulants are required to obtain reliable datasets. In the CRIEPI-led Dust Acquisition project, this paper focuses on the design and kilogram-scale fabrication of uranium-bearing FD simulants representative of major in-vessel and ex-vessel debris conditions at 1F. Five simulants were manufactured at CEA using thermite reactions, direct induction heating or combined processing, depending on thermochemical constraints and target compositions. A representative manufacturing example is presented to illustrate composition selection and optimization of thermite reaction in order to obtain complete melting and coherent blocks at the kilogram scale. As a result of this project and previously manufactured compositions in URASOL IRID-JAEA/CLADS project, some of the five FD representative blocks with multiphase (U-Zr-O oxide matrices with metallic inclusions and MCCI-like silicate-rich phases) and non-uniform aspect have been selected. Main features of the blocks are presented. They provide realistic FD for generation of aerosols by dry disc cutting on FUJISAN2 facility, designed within a collaboration between CRIEPI, ONET, CEA, and IRSN (now ASNR). Physical and chemical characterization of aerosols techniques are shortly presented.
- 4 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessFuel debris prototype fabrication and cutting in view of determining airborne release fraction for Fukushima Daiichi fuel debris retrieval
Estimating the Airborne Release Fraction (ARF) during fuel debris (FD) retrieval is important for the safe decommissioning of the Fukushima Daiichi Nuclear Power Plant (1F) because it supports exposure assessment and the design of mitigation measures. Dust generation during dry mechanical cutting depends not only on operating conditions but also strongly on the properties of the cut material, including size, geometry, mechanical behavior and multiphase heterogeneity. Therefore, representative simulants are required to obtain reliable datasets. In the CRIEPI-led Dust Acquisition project, this paper focuses on the design and kilogram-scale fabrication of uranium-bearing FD simulants representative of major in-vessel and ex-vessel debris conditions at 1F. Five simulants were manufactured at CEA using thermite reactions, direct induction heating or combined processing, depending on thermochemical constraints and target compositions. A representative manufacturing example is presented to illustrate composition selection and optimization of thermite reaction in order to obtain complete melting and coherent blocks at the kilogram scale. As a result of this project and previously manufactured compositions in URASOL IRID-JAEA/CLADS project, some of the five FD representative blocks with multiphase (U-Zr-O oxide matrices with metallic inclusions and MCCI-like silicate-rich phases) and non-uniform aspect have been selected. Main features of the blocks are presented. They provide realistic FD for generation of aerosols by dry disc cutting on FUJISAN2 facility, designed within a collaboration between CRIEPI, ONET, CEA, and IRSN (now ASNR). Physical and chemical characterization of aerosols techniques are shortly presented.
- 1 January 2022
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 386, 111511
Upgrading the PLINIUS platform toward smarter prototypic-corium experimental R&D
- 1 January 2022
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 386, 111511
Upgrading the PLINIUS platform toward smarter prototypic-corium experimental R&D
- 25 October 2021
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 59 (4) , 459-471
High-temperature ex-vessel corium spreading. Part 2: scaling principles for gravity-viscous spreading with slip at the melt–substrate interface
Promoting the spreading of molten corium represents a key strategy in the dissipation of decay heat and in the maintainence of containment integrity in the aftermath of a severe nuclear accident. Precise repeatability is difficult to achieve during high-temperature melt spreading experiments, and so scaling factors are necessary to correct for differences in flow rate, viscosity, and density between comparative experiments. A gravity-viscous momentum balance derived for spreading in the two-dimensional spreading geometry employed during recent kg-scale VE-U9 experiments on ceramic and sacrificial concrete substrates establishes that no-slip spreading length scales with the square root of the mass flow rate. Scaling for the reduced mass flow rate and enhanced viscosity implied that the melt spread 37% further on the sacrificial concrete than on the inert ceramic substrate. The possibility of a lubricating film of molten concrete and ablation gases reducing friction at the lower boundary is investigated through the imposition of a slip velocity proportional to the shear at the melt–substrate interface. Simulations over a range of Navier slip lengths implied that spreading length scales with the ratio of slip length to the melt thickness and that spreading length can be augmented by as much as 68% in the case of a virtually frictionless interface.- 25 October 2021
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 59 (4) , 459-471
High-temperature ex-vessel corium spreading. Part 2: scaling principles for gravity-viscous spreading with slip at the melt–substrate interface
Promoting the spreading of molten corium represents a key strategy in the dissipation of decay heat and in the maintainence of containment integrity in the aftermath of a severe nuclear accident. Precise repeatability is difficult to achieve during high-temperature melt spreading experiments, and so scaling factors are necessary to correct for differences in flow rate, viscosity, and density between comparative experiments. A gravity-viscous momentum balance derived for spreading in the two-dimensional spreading geometry employed during recent kg-scale VE-U9 experiments on ceramic and sacrificial concrete substrates establishes that no-slip spreading length scales with the square root of the mass flow rate. Scaling for the reduced mass flow rate and enhanced viscosity implied that the melt spread 37% further on the sacrificial concrete than on the inert ceramic substrate. The possibility of a lubricating film of molten concrete and ablation gases reducing friction at the lower boundary is investigated through the imposition of a slip velocity proportional to the shear at the melt–substrate interface. Simulations over a range of Navier slip lengths implied that spreading length scales with the ratio of slip length to the melt thickness and that spreading length can be augmented by as much as 68% in the case of a virtually frictionless interface.- 25 October 2021
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 59 (4) , 446-458
High-temperature ex-vessel corium spreading. Part 1: experimental investigations on ceramic and sacrificial concrete substrates
Optimizing melt spreading in the aftermath of a core disruptive accident is crucial for achieving sufficient melt cooling to maintain reactor containment integrity. Two ≈30 kg-scale experiments performed at the VULCANO facility explore the spreading of high-temperature molten corium-concrete mixtures over ceramic and sacrificial concrete substrates. Imaging of the melt front propagation revealed a 7% increase in spreading length and a 30% increase in maximum front velocity during spreading over sacrificial concrete, despite a reduced mass partaking in spreading due to increased holdup within the crucible. Infrared imaging of the melt indicated surface temperatures around 45°C lower during spreading on sacrificial concrete, resulting in a roughly three-fold increase in melt viscosity. The enhanced viscosity and reduced mass during the VE-U9-concrete test imply an increased spreadability on sacrificial concrete greater than the observed 7% increase in spreading length. This enhanced spreadability on sacrificial concrete could be explained by the apparent gliding motion of the melt, consistent with reduced friction at the melt-substrate interface. Reduced friction at the melt-substrate interface is best explained by a diphasic film of molten concrete and gaseous concrete decomposition products acting as a lubricant between the melt and solid substrate.
- 25 October 2021
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 59 (4) , 446-458
High-temperature ex-vessel corium spreading. Part 1: experimental investigations on ceramic and sacrificial concrete substrates
Optimizing melt spreading in the aftermath of a core disruptive accident is crucial for achieving sufficient melt cooling to maintain reactor containment integrity. Two ≈30 kg-scale experiments performed at the VULCANO facility explore the spreading of high-temperature molten corium-concrete mixtures over ceramic and sacrificial concrete substrates. Imaging of the melt front propagation revealed a 7% increase in spreading length and a 30% increase in maximum front velocity during spreading over sacrificial concrete, despite a reduced mass partaking in spreading due to increased holdup within the crucible. Infrared imaging of the melt indicated surface temperatures around 45°C lower during spreading on sacrificial concrete, resulting in a roughly three-fold increase in melt viscosity. The enhanced viscosity and reduced mass during the VE-U9-concrete test imply an increased spreadability on sacrificial concrete greater than the observed 7% increase in spreading length. This enhanced spreadability on sacrificial concrete could be explained by the apparent gliding motion of the melt, consistent with reduced friction at the melt-substrate interface. Reduced friction at the melt-substrate interface is best explained by a diphasic film of molten concrete and gaseous concrete decomposition products acting as a lubricant between the melt and solid substrate.
- Open Access
- 1 January 2017
- Published by University of Latvia in Magnetohydrodynamics
- Vol. 53 (4) , 611-618
Influence of skin depth on convective heat transfer in induction heating
- 1 January 2017
- Published by University of Latvia in Magnetohydrodynamics
- Vol. 53 (4) , 611-618
Open AccessInfluence of skin depth on convective heat transfer in induction heating