Tae-Hoon Jang
Research Subjects
Research Interests
Tae-Hoon Jang has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Chel-Jong Choi
School of Semiconductor and Chemical Engineering, Semiconductor Physics Research Center, (SPRC), Jeonbuk National University, Jeonju, Republic of Korea
2 shared publications - Kyu-Hwan Shim
Chonbuk National University
2 shared publications - Sakhone Pharkphoumy
School of Semiconductor and Chemical Engineering, Semiconductor Physics Research Center, Jeonbuk National University, Jeonju 54896, Republic of Korea
2 shared publications - Vallivedu Janardhanam
School of Semiconductor and Chemical Engineering, Semiconductor Physics Research Center (SPRC), Chonbuk National University 2 , Jeonju 54896, Republic of Korea
2 shared publications - Jaejun Park
School of Semiconductor and Chemical Engineering, Semiconductor Physics Research Center, Chonbuk National University, Jeonju 54896, Korea
1 shared publication
Latest Publications
- Open Access
- 20 February 2023
- Published by MDPI AG in Electronics
- Vol. 12 (4) , 1049
Correlation of Crystal Defects with Device Performance of AlGaN/GaN High-Electron-Mobility Transistors Fabricated on Silicon and Sapphire Substrates
Herein, the performance of AlGaN/GaN high-electron-mobility transistor (HEMT) devices fabricated on Si and sapphire substrates is investigated. The drain current of the AlGaN/GaN HEMT fabricated on sapphire and Si substrates improved from 155 and 150 mA/mm to 290 and 232 mA/mm, respectively, at VGS = 0 V after SiO2 passivation. This could be owing to the improvement in the two-dimensional electron gas charge and reduction in electron injection into the surface traps. The SiO2 passivation resulted in the augmentation of breakdown voltage from 245 and 415 V to 400 and 425 V for the AlGaN/GaN HEMTs fabricated on Si and sapphire substrates, respectively, implying the effectiveness of SiO2 passivation. The lower transconductance of the AlGaN/GaN HEMT fabricated on the Si substrate can be ascribed to the higher self-heating effect in Si. The X-ray rocking curve measurements demonstrated that the AlGaN/GaN heterostructures grown on sapphire exhibited a full-width half maximum of 368 arcsec against 703 arcsec for the one grown on Si substrate, implying a better crystalline quality of the AlGaN/GaN heterostructure grown on sapphire. The AlGaN/GaN HEMT fabricated on the sapphire substrate exhibited better performance characteristics than that on the Si substrate, owing to the high crystalline quality and improved surface.
- 20 February 2023
- Published by MDPI AG in Electronics
- Vol. 12 (4) , 1049
Open AccessCorrelation of Crystal Defects with Device Performance of AlGaN/GaN High-Electron-Mobility Transistors Fabricated on Silicon and Sapphire Substrates
Herein, the performance of AlGaN/GaN high-electron-mobility transistor (HEMT) devices fabricated on Si and sapphire substrates is investigated. The drain current of the AlGaN/GaN HEMT fabricated on sapphire and Si substrates improved from 155 and 150 mA/mm to 290 and 232 mA/mm, respectively, at VGS = 0 V after SiO2 passivation. This could be owing to the improvement in the two-dimensional electron gas charge and reduction in electron injection into the surface traps. The SiO2 passivation resulted in the augmentation of breakdown voltage from 245 and 415 V to 400 and 425 V for the AlGaN/GaN HEMTs fabricated on Si and sapphire substrates, respectively, implying the effectiveness of SiO2 passivation. The lower transconductance of the AlGaN/GaN HEMT fabricated on the Si substrate can be ascribed to the higher self-heating effect in Si. The X-ray rocking curve measurements demonstrated that the AlGaN/GaN heterostructures grown on sapphire exhibited a full-width half maximum of 368 arcsec against 703 arcsec for the one grown on Si substrate, implying a better crystalline quality of the AlGaN/GaN heterostructure grown on sapphire. The AlGaN/GaN HEMT fabricated on the sapphire substrate exhibited better performance characteristics than that on the Si substrate, owing to the high crystalline quality and improved surface.
- Open Access
- 28 October 2021
- Published by MDPI AG in Electronics
- Vol. 10 (21) , 2642
Optimized Device Geometry of Normally-On Field-Plate AlGaN/GaN High Electron Mobility Transistors for High Breakdown Performance Using TCAD Simulation
This study presents the optimization of the lateral device geometry and thickness of the channel and barrier layers of AlGaN/GaN high electron mobility transistors (HEMTs) for the enhancement of breakdown voltage (VBR) characteristics using a TCAD simulation. The effect of device geometry on the device performance was explored by varying the device design parameters, such as the field plate length (LFP), gate-to-drain length (LGD), gate-to-source length (LGS), gate length (LG), thickness of the Si3N4 passivation layer (Tox), thickness of the GaN channel (Tch), and AlGaN barrier (Tbarrier). The VBR was estimated from the off-state drain current versus the drain voltage (IDS–VDS) curve, and it exhibited a strong dependence on the length and thickness of the parameters. The optimum values of VBR for all the device’s geometrical parameters were evaluated, based on which, an optimized device geometry of the field-plated AlGaN/GaN HEMT structure was proposed. The optimized AlGaN/GaN HEMT structure exhibited VBR = 970 V at IGS = 0.14 A/mm, which was considerably higher than the results obtained in previous studies. The results obtained in this study could provide vital information for the selection of the device geometry for the implementation of HEMT structures.
- 28 October 2021
- Published by MDPI AG in Electronics
- Vol. 10 (21) , 2642
Open AccessOptimized Device Geometry of Normally-On Field-Plate AlGaN/GaN High Electron Mobility Transistors for High Breakdown Performance Using TCAD Simulation
This study presents the optimization of the lateral device geometry and thickness of the channel and barrier layers of AlGaN/GaN high electron mobility transistors (HEMTs) for the enhancement of breakdown voltage (VBR) characteristics using a TCAD simulation. The effect of device geometry on the device performance was explored by varying the device design parameters, such as the field plate length (LFP), gate-to-drain length (LGD), gate-to-source length (LGS), gate length (LG), thickness of the Si3N4 passivation layer (Tox), thickness of the GaN channel (Tch), and AlGaN barrier (Tbarrier). The VBR was estimated from the off-state drain current versus the drain voltage (IDS–VDS) curve, and it exhibited a strong dependence on the length and thickness of the parameters. The optimum values of VBR for all the device’s geometrical parameters were evaluated, based on which, an optimized device geometry of the field-plated AlGaN/GaN HEMT structure was proposed. The optimized AlGaN/GaN HEMT structure exhibited VBR = 970 V at IGS = 0.14 A/mm, which was considerably higher than the results obtained in previous studies. The results obtained in this study could provide vital information for the selection of the device geometry for the implementation of HEMT structures.