Hongri Fan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hongri Fan has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Bo Qian
School of Mechanical and Automotive Engineering, Shanghai University of Engineering Science, Shanghai, China
5 shared publications - Gang Liu
Shanghai University of Engineering Science
3 shared publications - Jianrui Zhang
School of Mechanical and Power Engineering, East China University of Science and Technology, Shanghai 200237, China
2 shared publications - Pei Li
School of Mechanical and Power Engineering, East China University of Science and Technology, Shanghai 200237, China
2 shared publications - Jianrui Zhang
School of Intelligent Manufacturing, Longdong University, Qingyang 745000, China
1 shared publication - Pei Li
School of Mechanical and Power Engineering, East China University of Science and Technology, Shanghai 200237, China
1 shared publication
Latest Publications
- Open Access
Heat Exchanging Grid Structures Based on Laser-Based Powder Bed Fusion: Formation Process and Boiling Heat Transfer Performance
Microchannel structures possess high efficiency and high boiling heat transfer coefficient of two-phase flow. In particular, the grid structure has the advantages of a simple pattern, large load capacity, and good surface adaptability. Employing the laser-based powder bed fusion (L-PBF) manufacturing technology, a new method of forming heat transfer grids with a controllable structure is proposed in this study. The formation principle, process, and the reasons for improvements in the boiling heat transfer performance were investigated with stainless steel materials. Laser scanning with varying scan spacings was used to prepare multiple structures with different grid widths and wall heights. On this basis, the porosity and pore morphology of the grid structures were analyzed, followed by pool boiling heat transfer experiments. The results revealed that the grid structure significantly affected the nucleate boiling behavior and increased the critical heat flux (CHF). It was found that the 0.5 mm sample exhibited optimum critical heat transfer performance, with an improvement of 10–27% compared to those of the other four samples (minimum of 63.3 W·cm−2 and maximum of 93.9 W·cm−2). In addition, for samples with a grid width greater than 0.5 mm, the boiling slightly decreased by <5%. When the grid width was further increased, the flow resistance effect and the bubble synapse generation effect tended to converge. In these cases, boiling heat transfer only occurred in a single phase along the direction of the medium wall thickness, thus failing to achieve two-phase heat transfer through bubble growth and collapse.
Open AccessHeat Exchanging Grid Structures Based on Laser-Based Powder Bed Fusion: Formation Process and Boiling Heat Transfer Performance
Microchannel structures possess high efficiency and high boiling heat transfer coefficient of two-phase flow. In particular, the grid structure has the advantages of a simple pattern, large load capacity, and good surface adaptability. Employing the laser-based powder bed fusion (L-PBF) manufacturing technology, a new method of forming heat transfer grids with a controllable structure is proposed in this study. The formation principle, process, and the reasons for improvements in the boiling heat transfer performance were investigated with stainless steel materials. Laser scanning with varying scan spacings was used to prepare multiple structures with different grid widths and wall heights. On this basis, the porosity and pore morphology of the grid structures were analyzed, followed by pool boiling heat transfer experiments. The results revealed that the grid structure significantly affected the nucleate boiling behavior and increased the critical heat flux (CHF). It was found that the 0.5 mm sample exhibited optimum critical heat transfer performance, with an improvement of 10–27% compared to those of the other four samples (minimum of 63.3 W·cm−2 and maximum of 93.9 W·cm−2). In addition, for samples with a grid width greater than 0.5 mm, the boiling slightly decreased by <5%. When the grid width was further increased, the flow resistance effect and the bubble synapse generation effect tended to converge. In these cases, boiling heat transfer only occurred in a single phase along the direction of the medium wall thickness, thus failing to achieve two-phase heat transfer through bubble growth and collapse.
- Open Access
Microchannel Liquid-Cooled Heat Exchanger Based on a Nonuniform Lattice: Study on Structure Calculation, Formation Process, and Boiling Heat Transfer Performance
A microchannel radiator is advantageous due to its high efficiency and large boiling heat transfer coefficient of two-phase flow. Based on the research of uniform lattice structures, this study proposed a microchannel heat exchanger with a nonuniform lattice structure. The calculation, optimal formation, and boiling heat transfer performance of the nonuniform lattice structure based on selective laser melting (SLM) were investigated, and heat exchange samples were successfully prepared using SLM. The porosity and pore morphology of the samples were analysed, and the contrast experiments of boiling heat transfer were conducted with deionised water. The results revealed that the heat flow density of the lattice structure was a minimum of 244% higher than that of the traditional liquid-cooled plate. The critical heat flux density of the lattice structure is 110 W∙cm−2, and the critical heat flux density of the traditional flat plate is 45 W∙cm−2. In addition, the effects of cell structures indicated that for frame cells, the heat transfer effect of nonuniform frames was inferior to that of uniform frames; for face-centred cubic (FCC) cells, the nonuniform and uniform frames exhibited the same trend. However, the heat flow density of FCC cells was 25% higher than that of frame structures.
Open AccessMicrochannel Liquid-Cooled Heat Exchanger Based on a Nonuniform Lattice: Study on Structure Calculation, Formation Process, and Boiling Heat Transfer Performance
A microchannel radiator is advantageous due to its high efficiency and large boiling heat transfer coefficient of two-phase flow. Based on the research of uniform lattice structures, this study proposed a microchannel heat exchanger with a nonuniform lattice structure. The calculation, optimal formation, and boiling heat transfer performance of the nonuniform lattice structure based on selective laser melting (SLM) were investigated, and heat exchange samples were successfully prepared using SLM. The porosity and pore morphology of the samples were analysed, and the contrast experiments of boiling heat transfer were conducted with deionised water. The results revealed that the heat flow density of the lattice structure was a minimum of 244% higher than that of the traditional liquid-cooled plate. The critical heat flux density of the lattice structure is 110 W∙cm−2, and the critical heat flux density of the traditional flat plate is 45 W∙cm−2. In addition, the effects of cell structures indicated that for frame cells, the heat transfer effect of nonuniform frames was inferior to that of uniform frames; for face-centred cubic (FCC) cells, the nonuniform and uniform frames exhibited the same trend. However, the heat flow density of FCC cells was 25% higher than that of frame structures.
- 24 November 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 119 (3-4) , 1553-1578
Fast calculation algorithm for region recognition and model interference ratio in the STL model based on voxel mapping decoupling
- 24 November 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 119 (3-4) , 1553-1578
Fast calculation algorithm for region recognition and model interference ratio in the STL model based on voxel mapping decoupling
- Open Access
Self-Supporting Microchannel Liquid-Cooled Plate for T/R Modules Based on Additive Manufacturing: Study on Its Pass Design, Formation Process and Boiling Heat Transfer Performance
The additive manufacturing technology of laser-based powder bed fusion (L-PBF), which is used to produce boiling heat transfer structures, offers a high processing flexibility and can provide lattice structures with a high surface-to-volume ratio. As an important part of the phased array radar, the plentiful transmit/receive (T/R) modules can generate considerable heat. Targeting this local overheating problem, this study discusses the pass design, the optimal formation process, and boiling heat transfer performance of microchannel liquid-cooled plates based on L-PBF additive manufacturing technology. The optimum design and process parameters were obtained by performing basic channel experiments. On this basis, the design and formation experiments of the microchannel structure were performed, and then the porosity and pore morphology of microchannel liquid-cooled plate samples were analysed. The boiling heat transfer experiments were conducted with deionised water, and the boiling heat transfer characteristics were compared with the saturated boiling curve of a traditional copper-tube liquid-cooled plate. The average wall temperature of the designed samples decreased by 4% compared with that of the traditional liquid-cooled plate under the same heat flow density the value reduced from 111.9 °C to 108.2 °C. Furthermore, within the same optimal boiling temperature range, the average heat flow densities of all the prepared samples increased by >60% compared with those of the traditional liquid-cooled plate the value increased from minimum 16 W∙cm−2 to maximum 34 W∙cm−2. The self-supporting microchannel structure can considerably improve the heat dissipation effect of T/R modules and solve the local overheating problem.
Open AccessSelf-Supporting Microchannel Liquid-Cooled Plate for T/R Modules Based on Additive Manufacturing: Study on Its Pass Design, Formation Process and Boiling Heat Transfer Performance
The additive manufacturing technology of laser-based powder bed fusion (L-PBF), which is used to produce boiling heat transfer structures, offers a high processing flexibility and can provide lattice structures with a high surface-to-volume ratio. As an important part of the phased array radar, the plentiful transmit/receive (T/R) modules can generate considerable heat. Targeting this local overheating problem, this study discusses the pass design, the optimal formation process, and boiling heat transfer performance of microchannel liquid-cooled plates based on L-PBF additive manufacturing technology. The optimum design and process parameters were obtained by performing basic channel experiments. On this basis, the design and formation experiments of the microchannel structure were performed, and then the porosity and pore morphology of microchannel liquid-cooled plate samples were analysed. The boiling heat transfer experiments were conducted with deionised water, and the boiling heat transfer characteristics were compared with the saturated boiling curve of a traditional copper-tube liquid-cooled plate. The average wall temperature of the designed samples decreased by 4% compared with that of the traditional liquid-cooled plate under the same heat flow density the value reduced from 111.9 °C to 108.2 °C. Furthermore, within the same optimal boiling temperature range, the average heat flow densities of all the prepared samples increased by >60% compared with those of the traditional liquid-cooled plate the value increased from minimum 16 W∙cm−2 to maximum 34 W∙cm−2. The self-supporting microchannel structure can considerably improve the heat dissipation effect of T/R modules and solve the local overheating problem.