JHJingcong He

Jingcong He

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jingcong He has a total of 25 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A Terahertz-Band Rectangular TE10 to Circular TE01 Mode Converter

    by Guoxiang Shu, Xinlun Xie, Junchen Ren, Guangxin Lin, Qi Li, Jujian Lin, Jiacai Liao, Jingcong He, Biaogang Xu, Zhiwei Chang, et al.

    The design, fabrication, and experimental measurement of a broadband and compact TE $^{\Box}_{\text{10}}$ –TE $^{\circ}_{\text{01}}$ (symbols $\Box$ $^{^{^{}}}$ and $\circ $ represent the rectangular and circular waveguides, respectively) mode converter is presented in this article. The proposed mode converter consists of three components, including a TE $^{\Box}_{\text{10}}$ –TE $^{\Box}_{\text{20}}$ mode converter based on a two-way H-T junction power divider, a TE $^{\Box}_{\text{20}}$ –TE $^{+}_{\text{22}}$ mode converter with variable cross-shaped waveguide, and a TE $^{+}_{\text{22}}$ –TE $^{\circ}_{\text{01}}$ mode converter. Two distinct design schemes have been employed for the first part of the TE $^{\Box}_{\text{10}}$ –TE $^{\circ}_{\text{01}}$ mode converter, which are based on two-way $^{^{^{}}}$ H-T junction power dividers with a path difference of odd times half-waveguide wavelength (Scheme 1) and a 180 $^{\circ}$ phase shifter (Scheme 2), respectively. This mode converter is highlighted by the significant advantage of high conversion efficiency over a wide bandwidth with a relatively easy-to-fabricate structure, which is evidenced by the measurement of two identical back-to-back joined mode converters based on Scheme 1. Measurement results matched with simulation ones within reasonable accuracy, which predicted that a 1-dB transmission bandwidth of $\sim$ 56.7 GHz was obtained. Meanwhile, the reflection coefficient S $_{\text{11}}$ was below $-$ 13.2 dB over that bandwidth.


  • Design and Experimental Verification of 0.34-THz Rectangular TE10 to TEn0 Mode Converters

    by Guangxin Lin, Guoxiang Shu, Jujian Lin, Qi Li, Jingcong He, Xinlun Xie, Huaxin Pan, Qingyi Guo, Xue Ren, Huabi Yin, et al.

    A novel rectangular TE $_{10}$ to rectangular TE $_{n0}$ ( $n=2, 3, 4, \ldots$ ) mode converter based on an $E$ -plane Y-shaped branch waveguide power dividing network is proposed in this article. To obtain the desired high-order mode, the signal observed at the output end of each adjacent branch waveguide of the power dividing network is designed to possess the property of equal amplitude and reversed phase. Three terahertz-band (300–400 GHz) rectangular TE $_{20}$ /TE $_{30}$ /TE $_{40}$ mode converters were designed and optimized, obtaining a 1-dB transmission bandwidth of 100.0 GHz (29.4%), 100.0 GHz (29.4%), and 67.2 GHz (19.8%), respectively. This kind of mode converter offers good flexibility to excite any TE $_{n0}$ modes with good electrical performance, including high mode conversion efficiency and low port reflection over a wide frequency bandwidth. The prototype of two identical rectangular TE $_{30}$ mode converters joined back-to-back was microfabricated and measured. The experimental measurement results were in good agreement with simulation predictions when the conductor ohmic loss, machining, and assembling errors were taken into account, which verifies the feasibility of the design methodology and manufacturing scheme for a mode converter operating above 300 GHz.


  • Study of a 0.3-THz Extended Interaction Oscillator Based on the Pseudospark-Sourced Sheet Electron Beam

    by Jiacai Liao, Guoxiang Shu, Guangxin Lin, Jujian Lin, Qi Li, Jingcong He, Junchen Ren, Zhiwei Chang, Biaogang Xu, Junzhe Deng, et al.

    Our previous experimental study of a 0.2-THz extended interaction oscillator (EIO) driven by the pseudospark-sourced (PS) sheet electron beam has revealed one key issue: the discrepancy between the simulated and measured output power was dramatically large. Around this issue, the design and analysis of an improved 0.3-THz EIO are presented in this article. To make the prediction closer to the actual situation, a few factors, including the plasma effect, the ohmic loss caused by the surface roughness, the effective beam current, and the energy spread, are analyzed and considered in the simulations. The plasma is equivalent to a dielectric. To verify the design, the interaction circuit of the 0.3-THz EIO was microfabricated. Its RF performance was measured by using a vector network analyzer, which was in good agreement with the simulation prediction, and its surface roughness was measured by using an optical 3-D surface profiler. Beam–wave interaction simulations having considered the ohmic loss, energy spread, and plasma effect predicted that the upgraded EIO still could produce an output power of 16.3 W at 295.3 GHz.


  • Preliminary Research of a Terahertz Band High-Order Mode Backward Wave Oscillator

    by Jiacai Liao, Guoxiang Shu, Jingcong He, Junchen Ren, Jujian Lin, Guangxin Lin, Qi Li, Wenlong He

  • A Sub-THz High-Order Mode Backward Wave Oscillator Driven by Pseudospark Sourced Multiple Sheet Electron Beams

    by Guoxiang Shu, Jiacai Liao, Jingcong He, Junchen Ren, Jujian Lin, Guangxin Lin, Qi Li, Cunjun Ruan, Wenlong He

    A novel concept of combining the advantages of pseudospark (PS)-sourced electron beam (high beam current density), multiple-sheet-electron-beams (large total beam cross-sectional area), and high-order mode (HOM) slow wave structure (SWS) (high power capacity) to produce high-power terahertz signals is presented in this article. As an example, a sub-terahertz backward wave oscillator (BEO) driven by PS-sourced dual-sheet-electron-beams is designed. Measured results of the interaction circuit, including transmission/reflection coefficients and the dispersion relation, were in good agreement with simulation predictions. Beam-wave interaction simulations having considered the plasma effect and conductor loss predicted stable output signals with radiation power of 167.4–255.4 W over a tunable bandwidth of 234.4–241.0 GHz.


  • Demonstration of a Wideband and Compact Input–Output Coupling Structure for Subterahertz Sheet-Beam Traveling Wave Amplifiers

    by Guoxiang Shu, Jiacai Liao, Jingcong He, Junchen Ren, Junzhe Deng, Zhiwei Chang, Yanyan Tian, Cunjun Ruan, Wenlong He

    A novel methodology for the beam-wave division/combination in a sheet beam traveling wave amplifier (SB-TWT) is proposed. The design, microfabrication, and measurement of an H -band (220–325 GHz) input–output coupling structures, which originates from an E -plane Riblet coupler with one shorted port, are presented in this article. To experimentally validate the proposed methodology, the designed input–output coupling structure was manufactured by using nanocomputer numerical control milling and measured by using a vector network analyzer. A 3-dB transmission bandwidth of ∼94.0 GHz (231.0–325.0 GHz, 33.8% fractional bandwidth) was measured, over which the measured reflection and isolation coefficients were smaller than –15.3 dB and –11.6 dB, respectively. Compared with other previously reported input–output coupling structures for SB-TWTs, this structure is highlighted by its superior comprehensive performance, including compact geometry, insensitive to the manufacturing tolerance, and good electrical performance over a wide frequency bandwidth, which makes it especially applicable in the terahertz-band operation.


  • A Terahertz Band TE20□ Mode Input/Output Coupling Structure for Dual-Sheet-Beam Traveling-Wave Tubes

    by Jiacai Liao, Guoxiang Shu, Jingcong He, Junchen Ren, Jujian Lin, Junzhe Deng, Zhiwei Chang, Biaogang Xu, Cunjun Ruan, Wenlong He

    This article presents the design, microfab- rication, and measurement of a terahertz band ${\mathrm {TE}}^{\Box }_{20}$ mode input–output coupling structure for dual-sheet-beam traveling-wave tubes (TWTs). The proposed coupling structure is based on an $E$ -plane Riblet slot coupler with one shorted port and a ${\mathrm {TE}}^{\Box }_{10}$ – ${\mathrm {TE}}^{\Box }_{20}$ mode converter. Compared to the previously reported high-order mode (HOM) coupling structures, the proposed structure possesses superior electrical and mechanical performance, including better reflection/transmission properties and relatively easy-to-fabricate configuration with features insensitive to fabrication tolerances. For verification, two $H$ -band (220–325 GHz) identical ${\mathrm {TE}}^{\Box }_{20}$ mode coupling structures joined back-to-back were manufactured and measured. Good agreement between the experimental results and the simulated responses is observed. The fabricated prototype of the coupling structure exhibits good electromagnetic (EM) performance over a bandwidth of 52.1 GHz (243.2–295.3 GHz) with a transmission coefficient better than −1.5 dB and a port reflection lower than −15.0 dB.


  • An Easy-to-Fabricate Circular TE₂₁/TE₀₁ Mode Generator

    by Junchen Ren, Guoxiang Shu, Jingcong He, Jiacai Liao, Junzhe Deng, Jujian Lin, Cunjun Ruan, Wenlong He

    The design, fabrication, and cold test of a mode generator to excite the circular TE 01 or TE 21 mode for ${H}$ -band (220–325 GHz) gyrotron traveling-wave-tubes (TWTs) are presented in this article. The mode generator is composed of two parts: a TE $^{\Box }_{10}$ –TE $^{\Box }_{20}$ mode converter based on a two-way H-T junction power divider and a TE $^{\Box }_{20}$ –TE $^{\circ }_{01}$ /TE $^{\circ }_{{21{ }}}$ mode converter with a tapered waveguide ( $^{{\Box { }}}$ and ° represent the rectangular and circular waveguide, respectively). By adjusting the ratio of width and height of the tapered waveguide, the TE $^{\circ }_{01}$ or TE $^{\circ }_{\vphantom {D_{l}}21}$ mode could be excited. The primary advantage of this technique is that it has a relatively compact and easy-to-fabricate configuration, which is especially useful in the terahertz-band. To verify the design, two identical mode generators joined back-to-back were manufactured and measured. The measured ${S}$ -parameters were in good agreement with the simulated ones, which predicted that the TE $^{\circ }_{\vphantom {D_{l}}21}$ /TE $^{\circ }_{01}$ mode generator obtained a 1-dB transmission bandwidth of ~38.1 and ~48.0 GHz, respectively. Meanwhile the reflection coefficient $S_{11}$ was below −10 dB over that bandwidth.


  • Dispersion and Dielectric Attenuation Properties of a Wideband Double-Staggered Grating Waveguide for Subterahertz Sheet-Beam Traveling-Wave Amplifiers

    by Guoxiang Shu, Jiacai Liao, Junchen Ren, Jingcong He, Junzhe Deng, Zhiwei Chang, Biaogang Xu, Gang Wang, Cunjun Ruan, Wenlong He

    The dispersion and dielectric attenuation characteristics of a double-staggered grating waveguide (DSGW) are two crucial features related to the output characteristics of a sheet-beam traveling-wave amplifier and have been previously studied by using theoretical analysis and simulations. In this work, these two characteristics are both experimentally studied. Two ${H}$ -band (220–325 GHz) DSGW circuit prototypes with and without dielectric attenuators made of the BeO-TiO 2 composite ceramic were machined by using nanocomputer numerical control milling. Experimental studies of the dispersion property were performed successfully where the measurement results were in good agreement with those predicted by simulations, exhibiting a wide passband of 70 GHz (230–300 GHz). The measured transmission coefficient has been decreased from −5 to −55 dB after the introduction of dielectric attenuators, experimentally verifying the feasibility of the adopted methodology. The effects of the variations of dispersion relation and transmission loss on the beam-wave interaction stability were also investigated.


  • Development of a Sub-terahertz Sheet Beam Travelling Wave Tube

    by Guoxiang Shu, Zhihui Ouyang, Lin Zhang, Jiacai Liao, Junchen Ren, Jingcong He, Wenlong He

    The sheet beam travelling wave tube (SB-TWT) is a promising sub-terahertz amplifier with high output power and wide frequency bandwidth. The design of key components operating within the H-band (220–325 GHz), including a sheet electron beam gun, an offset-pole periodic cusped magnet, and a high frequency system composed of input/output couplers as well as a double staggered grating waveguide slow-wave structure, is presented in this paper. Beam-wave interaction simulations with the ohmic loss being taken into account predicted that the amplifier produced an output power of >55 W in the frequency range of 230–280 GHz.