Ivan Stojadinovic
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Ivan Stojadinovic has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Dragan Adamovic
Faculty of Engineering, University of Kragujevac, 34000 Kragujevac, Serbia
1 shared publication - Fatima Zivic
Faculty of Engineering, University of Kragujevac, Sestre Janjić 6, 34000 Kragujevac, Serbia
1 shared publication - Jelena Stevanovic
University of Kragujevac, Serbia
1 shared publication - Jovan Tanasković
Faculty of Mechanical Engineering, University of Belgrade, 11120 Belgrade, Serbia
1 shared publication - Nenad Grujovic
Faculty of Engineering, University of Kragujevac, Sestre Janjić 6, 34000 Kragujevac, Serbia
1 shared publication - Slobodan Mitrović
University of Kragujevac, Faculty of Engineering
1 shared publication
Latest Publications
- 1 January 2026
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in Medicinski casopis
- Vol. 60 (3) , 139-142
Functional gait assessment scales before and after orthopedic treatment
Monitoring and analyzing gait before and after surgical treatment is a very important parameter in the recovery of patients. Independent walking is necessary for independence in activities of daily living. The consequences of gait disorders can be influenced by weakness of the muscles, limitation of movement in the joints, degenerative changes in the joints, and injuries. Gait analysis is important in order for the individual approach to the patient to be as the best possible and the rehabilitation treatment to be as successful as possible. To monitor functional recovery and find the best possible therapeutic program, a comprehensive and standardized functional assessment is necessary. There are numerous tests and scales that, with their numerical values, enable the quantification of existing gait deficits and their monitoring over time. Since we can monitor different characteristics when assessing gait, there are scalesfor monitoring the determination of gait characteristics. To test walking speed, we use the scales for walking speed Timed Up and Go test, 10-meter walk test, the four square step test. We monitor the walking distance using cadence (number of steps/min). Functional movement can be tested using Functional gait assessment, Dynamic Gait Index, Functional Ambulation Category
- 1 January 2026
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in Medicinski casopis
- Vol. 60 (3) , 139-142
Functional gait assessment scales before and after orthopedic treatment
Monitoring and analyzing gait before and after surgical treatment is a very important parameter in the recovery of patients. Independent walking is necessary for independence in activities of daily living. The consequences of gait disorders can be influenced by weakness of the muscles, limitation of movement in the joints, degenerative changes in the joints, and injuries. Gait analysis is important in order for the individual approach to the patient to be as the best possible and the rehabilitation treatment to be as successful as possible. To monitor functional recovery and find the best possible therapeutic program, a comprehensive and standardized functional assessment is necessary. There are numerous tests and scales that, with their numerical values, enable the quantification of existing gait deficits and their monitoring over time. Since we can monitor different characteristics when assessing gait, there are scalesfor monitoring the determination of gait characteristics. To test walking speed, we use the scales for walking speed Timed Up and Go test, 10-meter walk test, the four square step test. We monitor the walking distance using cadence (number of steps/min). Functional movement can be tested using Functional gait assessment, Dynamic Gait Index, Functional Ambulation Category
- 5 November 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
- Vol. 236 (10) , 2004-2012
Influence of different environments on the sliding friction of Ultra-high-molecular-weight polyethylene (UHMWPE)
Dynamic friction coefficient (COF) of the reciprocating sliding contact of the conventional UHMWPE, was investigated in four different environments (dry contact; distilled water; pure Ringer's solution and with PMMA particles), at five values of low normal load (0.1–1 N) and three values of sliding speed (4 - 12 mm/s). Significant differences of COF values occurred at the lowest load (0.1 N), whereas sliding speed did not influence COF values. Addition of PMMA particles in Ringer's solution produced significant increase of COF values, especially at the lowest load of 0.1 N. For the dry contact and the highest load (1 N), steady state was reached shortly after the beginning of the test and friction coefficient had uniform behaviour. In the case of wet environment and the lowest load, steady state was not reached and the friction coefficient exhibited non-reproducible random behaviour. According to the Hertz theory, 0.5 N load corresponded to the elastic stress of 48.7 MPa, thus surpassing the values of the elastic limits, hardness and true yield stress of the UHMWPE, and the behaviour of the friction coefficient was drastically different below and above this load value. It can be assumed that below the 0.5 N load, viscoelastic response, accompanied with plastic deformation is dominant, with transition to mainly plastic deformation for the higher loads.
- 5 November 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
- Vol. 236 (10) , 2004-2012
Influence of different environments on the sliding friction of Ultra-high-molecular-weight polyethylene (UHMWPE)
Dynamic friction coefficient (COF) of the reciprocating sliding contact of the conventional UHMWPE, was investigated in four different environments (dry contact; distilled water; pure Ringer's solution and with PMMA particles), at five values of low normal load (0.1–1 N) and three values of sliding speed (4 - 12 mm/s). Significant differences of COF values occurred at the lowest load (0.1 N), whereas sliding speed did not influence COF values. Addition of PMMA particles in Ringer's solution produced significant increase of COF values, especially at the lowest load of 0.1 N. For the dry contact and the highest load (1 N), steady state was reached shortly after the beginning of the test and friction coefficient had uniform behaviour. In the case of wet environment and the lowest load, steady state was not reached and the friction coefficient exhibited non-reproducible random behaviour. According to the Hertz theory, 0.5 N load corresponded to the elastic stress of 48.7 MPa, thus surpassing the values of the elastic limits, hardness and true yield stress of the UHMWPE, and the behaviour of the friction coefficient was drastically different below and above this load value. It can be assumed that below the 0.5 N load, viscoelastic response, accompanied with plastic deformation is dominant, with transition to mainly plastic deformation for the higher loads.