Mikhail Kravtsov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mikhail Kravtsov has a total of 66 co-authors. Here are the top co-authors by number of shared publications:
- Boris Pospelov
Scientific-methodical Center of Educational Institutions in the Sphere of Civil Defence
3 shared publications - Oleksiy Bazhinov
Kharkiv National Automobile and Highway University
3 shared publications - Olena Petrova
Mykolayiv National Agrarian University
3 shared publications - Yuliia Bezuhla
National University of Civil Defence of Ukraine
3 shared publications - Dmytro Saveliev
National University of Civil Defence of Ukraine
2 shared publications - Evgeniy Rybka
National University of Civil Protection of Ukraine
2 shared publications
Latest Publications
- Open Access
- 18 October 2026
- Published by MDPI AG in World Electric Vehicle Journal
- Vol. 17 (10) , 539
Computational and Experimental Analysis of Spatial Distribution and Spectral Composition of Electromagnetic Fields Inside a Vehicle Cabin
This paper estimates the total electromagnetic load in the passenger compartment. A computational model is proposed based on the numerical solution of Maxwell’s equations and the specular reflection method for near-field emitters, accounting for the shielding properties of the metal body and attenuation through the glazing apertures. Theoretical calculations and field measurements were performed using a spectrum analyzer (Narda NBM-550) and isotropic probes over the frequency range from 10 Hz to 3 GHz during various operating modes of the power plant and auxiliary electrical equipment. The comprehensive measurement campaign utilized two complementary metrological systems to cover the entire spectrum: a dedicated Narda EHP-50F isotropic analyzer was deployed for the low-frequency domain (10 Hz–100 kHz), while high-frequency electromagnetic and radiofrequency components (100 kHz–3 GHz) were acquired using a Narda NBM-550 broadband field meter equipped with isotropic electric (EF-0391) and magnetic (HF-3061) probes. The maximum low-frequency magnetic induction (B max = 2.4 μT) was recorded near the driver’s pedal unit and the engine shield, attributable to generator field leakage and ignition-system transients. In the high-frequency range (2.4 GHz), resonant effects of the metal body caused standing-wave interference nodes, producing electric field strength peaks of 8.5–9.5 V/m. Although the recorded field parameters are within the limits specified by ICNIRP and national sanitary standards, they pose a chronic exposure risk to drivers traveling long distances. Design recommendations are proposed to optimize the wiring topology and local shielding.
- 18 October 2026
- Published by MDPI AG in World Electric Vehicle Journal
- Vol. 17 (10) , 539
Open AccessComputational and Experimental Analysis of Spatial Distribution and Spectral Composition of Electromagnetic Fields Inside a Vehicle Cabin
This paper estimates the total electromagnetic load in the passenger compartment. A computational model is proposed based on the numerical solution of Maxwell’s equations and the specular reflection method for near-field emitters, accounting for the shielding properties of the metal body and attenuation through the glazing apertures. Theoretical calculations and field measurements were performed using a spectrum analyzer (Narda NBM-550) and isotropic probes over the frequency range from 10 Hz to 3 GHz during various operating modes of the power plant and auxiliary electrical equipment. The comprehensive measurement campaign utilized two complementary metrological systems to cover the entire spectrum: a dedicated Narda EHP-50F isotropic analyzer was deployed for the low-frequency domain (10 Hz–100 kHz), while high-frequency electromagnetic and radiofrequency components (100 kHz–3 GHz) were acquired using a Narda NBM-550 broadband field meter equipped with isotropic electric (EF-0391) and magnetic (HF-3061) probes. The maximum low-frequency magnetic induction (B max = 2.4 μT) was recorded near the driver’s pedal unit and the engine shield, attributable to generator field leakage and ignition-system transients. In the high-frequency range (2.4 GHz), resonant effects of the metal body caused standing-wave interference nodes, producing electric field strength peaks of 8.5–9.5 V/m. Although the recorded field parameters are within the limits specified by ICNIRP and national sanitary standards, they pose a chronic exposure risk to drivers traveling long distances. Design recommendations are proposed to optimize the wiring topology and local shielding.
- 25 June 2025
- Published by Dnipro University of Technology in Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu
- No. 3,p. 107-118
Optimization of electromagnetic radiation by hybrid and electric vehicles
Purpose. Improvement of electromagnetic radiation evaluation methods depending on working conditions of the vehicle. This will optimize the electromagnetic hazard of electric vehicles, hybrids and ordinary cars using a unified approach to the study of the magnetic field, regardless of the structure and design circuits of their power plants at the operation stage. Methodology. The methodological basis of the work is the generalization and analysis of known scientific results on the organization of the test system, the development and application of efficiency criteria, the rational combination of theoretical and experimental research and the use of a systemic approach. The object of the study is the process of determining the electromagnetic pollution of electric and hybrid vehicles at the operation stage, which minimizes the vector quality criterion depending on external conditions. Findings. A flexible protective fabric has been developed that allows for increased effective protection of the driver and passengers from electromagnetic radiation in the vehicle interior. Originality. The concept of modeling, optimization of the assessment of the electromagnetic hazard of electric and hybrid vehicles, which have a single approach to the study of the induced magnetic field voltage, is provided. Particular attention is paid to the estimate of the EMC frequency spectrum, which covers both low frequencies (characteristic of inverters) and high-frequency noise (electric motors). Testing in real operating conditions allows considering the impact of variable factors, such as temperature, humidity and features of road conditions. Practical value. The development of this study has a wide potential for improving technical solutions, expanding their scope, improving the methodology and integration of innovative technologies. At the same time, special attention should be paid to social, economic and regulatory aspects, which will ensure efficient and safe solution to the problem on a global scale.
- 25 June 2025
- Published by Dnipro University of Technology in Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu
- No. 3,p. 107-118
Optimization of electromagnetic radiation by hybrid and electric vehicles
Purpose. Improvement of electromagnetic radiation evaluation methods depending on working conditions of the vehicle. This will optimize the electromagnetic hazard of electric vehicles, hybrids and ordinary cars using a unified approach to the study of the magnetic field, regardless of the structure and design circuits of their power plants at the operation stage. Methodology. The methodological basis of the work is the generalization and analysis of known scientific results on the organization of the test system, the development and application of efficiency criteria, the rational combination of theoretical and experimental research and the use of a systemic approach. The object of the study is the process of determining the electromagnetic pollution of electric and hybrid vehicles at the operation stage, which minimizes the vector quality criterion depending on external conditions. Findings. A flexible protective fabric has been developed that allows for increased effective protection of the driver and passengers from electromagnetic radiation in the vehicle interior. Originality. The concept of modeling, optimization of the assessment of the electromagnetic hazard of electric and hybrid vehicles, which have a single approach to the study of the induced magnetic field voltage, is provided. Particular attention is paid to the estimate of the EMC frequency spectrum, which covers both low frequencies (characteristic of inverters) and high-frequency noise (electric motors). Testing in real operating conditions allows considering the impact of variable factors, such as temperature, humidity and features of road conditions. Practical value. The development of this study has a wide potential for improving technical solutions, expanding their scope, improving the methodology and integration of innovative technologies. At the same time, special attention should be paid to social, economic and regulatory aspects, which will ensure efficient and safe solution to the problem on a global scale.
- Open Access
- 30 December 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (5 (132)) , 6-12
Detection of fire by comparison of sampling coefficients of variation of current measurements of dangerous parameters of the gas environment
The object of this study is the selective coefficient of variation of dangerous parameters of the gas environment, which are caused by the general aggregates of reliable absence or occurrence of ignition of materials. The method of prompt detection of fires based on the comparison of the sample coefficients of variation of the hazardous parameters of the gas environment of the specified general populations and the verification for each moment of time of the result of the comparison of the sample coefficients of variation and exceeding the current threshold is theoretically substantiated. At the same time, the value of the current threshold is calculated taking into account the given probability of false detection of ignition and the current error of the result of comparing the sample coefficients of variation. This method makes it possible to ensure the maximum current probability of correct ignition detection. Experiments were conducted to verify the performance of the proposed method. The obtained results in general indicate the efficiency of the method. It was established that the result of the comparison of the sample coefficients of variation of the hazardous parameters of the gas environment, which correspond to the specified general populations for carbon monoxide at the time of ignition of alcohol, paper, wood, and textiles, is 0.47, 0.14, 0.2, and 0.001, respectively. For the temperature, the results of the comparison of the sample coefficients of variation during the ignition of similar materials are 0.12, 0.13, 0.015 and 0.045, respectively. At the same time, for prompt detection of fires based on the proposed method, it is necessary to preferably use the concentration of carbon monoxide and the temperature of the gas environment as dangerous parameters of the gas environment. The practical importance of the research is the use of selective coefficients of hazardous parameters of the gas environment for the detection of material fires in real time
- 30 December 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (5 (132)) , 6-12
Open AccessDetection of fire by comparison of sampling coefficients of variation of current measurements of dangerous parameters of the gas environment
The object of this study is the selective coefficient of variation of dangerous parameters of the gas environment, which are caused by the general aggregates of reliable absence or occurrence of ignition of materials. The method of prompt detection of fires based on the comparison of the sample coefficients of variation of the hazardous parameters of the gas environment of the specified general populations and the verification for each moment of time of the result of the comparison of the sample coefficients of variation and exceeding the current threshold is theoretically substantiated. At the same time, the value of the current threshold is calculated taking into account the given probability of false detection of ignition and the current error of the result of comparing the sample coefficients of variation. This method makes it possible to ensure the maximum current probability of correct ignition detection. Experiments were conducted to verify the performance of the proposed method. The obtained results in general indicate the efficiency of the method. It was established that the result of the comparison of the sample coefficients of variation of the hazardous parameters of the gas environment, which correspond to the specified general populations for carbon monoxide at the time of ignition of alcohol, paper, wood, and textiles, is 0.47, 0.14, 0.2, and 0.001, respectively. For the temperature, the results of the comparison of the sample coefficients of variation during the ignition of similar materials are 0.12, 0.13, 0.015 and 0.045, respectively. At the same time, for prompt detection of fires based on the proposed method, it is necessary to preferably use the concentration of carbon monoxide and the temperature of the gas environment as dangerous parameters of the gas environment. The practical importance of the research is the use of selective coefficients of hazardous parameters of the gas environment for the detection of material fires in real time
- Open Access
- 30 April 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (6 (128)) , 14-19
Development of conditions for obtaining oil from sunflower oil hydration waste
The object of the study is the process of treatment of sunflower phosphatide concentrate using sodium chloride solution. Hydration is a stage of oil refining. The waste of the process is a phosphatide concentrate, the disposal of which is dangerous to the environment. The concentrate contains valuable components – oil and phosphatides. An important task is to separate these components for effective use in various industries. The process of extracting oil from phosphatide concentrate by hydration in the presence of sodium chloride solution was investigated. The influence of the concentrate treatment conditions on the oil yield was determined. A sample of concentrate according to SOU 15.4-37-212:2004 (CAS 3436-44-0) was used: mass fraction of moisture and volatile substances – 2.8 %, mass fraction of phosphatides – 41.5 %. The concentrate was treated with sodium chloride solution with a concentration of (5–20) %. The hydration time was 25 min., the temperature was 45 °C, and the mass ratio of the sodium chloride solution to the concentrate was 1:1. Conditions for the concentrate treatment were determined: the concentration of sodium chloride solution was 15 %, settling time was 5 hours. At the same time, the yield of oil was 86.9 %. The parameters of the extracted oil were determined: acid value 2.8 mg KOH/g, peroxide value 3.2 ½ O mmol/kg, mass fraction of moisture and volatile substances 0.12 %. According to these indicators, the extracted oil corresponds to first-grade unrefined unfrozen sunflower oil according to DSTU 4492. The mass fraction of phosphorus-containing substances in terms of stearooleolecithin was 1.7 %, which slightly exceeds the standard value. The research results make it possible to process hydration waste and obtain oil, which is a raw material for the products of many industries. This will help solve the problem of disposal of environmentally hazardous waste and improve the state of the environment
- 30 April 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (6 (128)) , 14-19
Open AccessDevelopment of conditions for obtaining oil from sunflower oil hydration waste
The object of the study is the process of treatment of sunflower phosphatide concentrate using sodium chloride solution. Hydration is a stage of oil refining. The waste of the process is a phosphatide concentrate, the disposal of which is dangerous to the environment. The concentrate contains valuable components – oil and phosphatides. An important task is to separate these components for effective use in various industries. The process of extracting oil from phosphatide concentrate by hydration in the presence of sodium chloride solution was investigated. The influence of the concentrate treatment conditions on the oil yield was determined. A sample of concentrate according to SOU 15.4-37-212:2004 (CAS 3436-44-0) was used: mass fraction of moisture and volatile substances – 2.8 %, mass fraction of phosphatides – 41.5 %. The concentrate was treated with sodium chloride solution with a concentration of (5–20) %. The hydration time was 25 min., the temperature was 45 °C, and the mass ratio of the sodium chloride solution to the concentrate was 1:1. Conditions for the concentrate treatment were determined: the concentration of sodium chloride solution was 15 %, settling time was 5 hours. At the same time, the yield of oil was 86.9 %. The parameters of the extracted oil were determined: acid value 2.8 mg KOH/g, peroxide value 3.2 ½ O mmol/kg, mass fraction of moisture and volatile substances 0.12 %. According to these indicators, the extracted oil corresponds to first-grade unrefined unfrozen sunflower oil according to DSTU 4492. The mass fraction of phosphorus-containing substances in terms of stearooleolecithin was 1.7 %, which slightly exceeds the standard value. The research results make it possible to process hydration waste and obtain oil, which is a raw material for the products of many industries. This will help solve the problem of disposal of environmentally hazardous waste and improve the state of the environment
- Open Access
- 31 October 2023
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (10 (125)) , 53-62
Dynamics of skewness and kurtosis of dangerous environmental parameters in the event of fire
The object of this study is the dynamics of skewness and kurtosis of the selective distribution of dangerous parameters of the gas environment in the current time when materials are ignited. The theoretical substantiation of the methodology for determining the dynamics of skewness and kurtosis based on a sample of an arbitrary size of dangerous parameters of the gas medium moving in the current time of observation has been performed. Thresholds for current skewness and kurtosis are determined depending on sample size and null hypothesis significance levels. The procedure makes it possible to investigate the peculiarities of the dynamics of skewness and kurtosis and to identify moments of time for which alternative hypotheses (stability of parameter dynamics) are valid. Laboratory experiments were conducted to study the dynamics of skewness and kurtosis in terms of carbon monoxide concentration, smoke density, and the temperature of the gas environment during the ignition of alcohol and textiles. The results indicate that the investigated dangerous parameters are generally not Gaussian in the observation interval. It was found that the nature of the dynamics of measures of the current sample distributions of dangerous parameters depends on the type of ignition material and the dangerous parameter. It was established that in the absence of ignition, the dynamics of skewness and kurtosis of dangerous parameters is characterized by different directional skewness and kurtosis. In the event of ignition, the dynamics of skewness and kurtosis are fluctuating (from –4 to 18), which indicates the instability of the development of the dangerous parameter over time. The specified procedure creates an opportunity to detect the instability of the development of a dangerous parameter, which in practice makes it possible to detect the occurrence of fires (with a given reliability) in order to eliminate them and prevent the occurrence of a fire
- 31 October 2023
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (10 (125)) , 53-62
Open AccessDynamics of skewness and kurtosis of dangerous environmental parameters in the event of fire
The object of this study is the dynamics of skewness and kurtosis of the selective distribution of dangerous parameters of the gas environment in the current time when materials are ignited. The theoretical substantiation of the methodology for determining the dynamics of skewness and kurtosis based on a sample of an arbitrary size of dangerous parameters of the gas medium moving in the current time of observation has been performed. Thresholds for current skewness and kurtosis are determined depending on sample size and null hypothesis significance levels. The procedure makes it possible to investigate the peculiarities of the dynamics of skewness and kurtosis and to identify moments of time for which alternative hypotheses (stability of parameter dynamics) are valid. Laboratory experiments were conducted to study the dynamics of skewness and kurtosis in terms of carbon monoxide concentration, smoke density, and the temperature of the gas environment during the ignition of alcohol and textiles. The results indicate that the investigated dangerous parameters are generally not Gaussian in the observation interval. It was found that the nature of the dynamics of measures of the current sample distributions of dangerous parameters depends on the type of ignition material and the dangerous parameter. It was established that in the absence of ignition, the dynamics of skewness and kurtosis of dangerous parameters is characterized by different directional skewness and kurtosis. In the event of ignition, the dynamics of skewness and kurtosis are fluctuating (from –4 to 18), which indicates the instability of the development of the dangerous parameter over time. The specified procedure creates an opportunity to detect the instability of the development of a dangerous parameter, which in practice makes it possible to detect the occurrence of fires (with a given reliability) in order to eliminate them and prevent the occurrence of a fire
- Open Access
- 4 September 2023
- Published by O.M.Beketov National University of Urban Economy in Kharkiv in Municipal economy of cities
- Vol. 4 (178) , 206-209
FIRE HAZARD OF HYBRID AND ELECTRICAND VEHICLES
In the following time, we received information from many countries of the world about accidents related to fires and explosions of motor vehicles with electric and hybrid vehicles. The popularity of such news is caused by the fact that accidents and fires of cars with internal combustion engines have long become commonplace, which do not attract the attention of the general public. However, many numerous and conducted scientific studies say about the danger of electric and hybrid vehicle models with lithium-ion batteries that they are greatly exaggerated, i.e., damage to the traction battery (battery) can cause a self-destructive chain reaction, but the degree the danger of electrolyte is less than that of gasoline or diesel fuel and much less than that of hydrogen fuel in hybrid modifications. The article examines the causes of the fire hazard of electric and hybrid cars and their consequences. Scientific reasons and innovations regarding the prevention and immediate elimination of short circuits, fires and explosions in the closed space of lithium-ion batteries during the operation of electric hybrid cars are provided. Electric vehicles and hybrids tend to suffer from traction battery technical and other issues. Although a battery flash is dangerous and more difficult to extinguish than a gas flash, the cause of the fire is usually different and these results are found in a defect in the battery pack: "ruptured anode" and "complex separator". The Hyundai Kona and Chevrolet Bolt EV had the most electric vehicle recalls related to fires this year, totaling 152,000 vehicles, while the top two hybrid recalls totaled more than 32,000 vehicles. A lithium-ion type of car catches fire usually not immediately, but after some time. This determines the driver and passengers to immediately leave the interior of the vehicle. When extinguishing a fire, there is a risk of damage to passengers, eyewitnesses and others who are near it by the electric current of high-voltage systems. It is recommended to get out of the interior of the car engulfed in fire and smoke in a timely manner and call the rescuers of the Ministry of Emergency Situations by calling the emergency service. The main task of the firefighters who arrived in the city at the first stage of the event was to disconnect the high-voltage cable using an emergency disconnector or mechanically and to disconnect the high-voltage traction battery. Although the risk of flash in EVs and hybrids exists, it may be receiving a disproportionate amount of attention. It is important for car manufacturers to eliminate the risk of ignition in their vehicles as much as possible, but obviously no form of driving is completely safe. Keywords: hybrid and electricand car, fire, explosion, lithium-ion battery.
- 4 September 2023
- Published by O.M.Beketov National University of Urban Economy in Kharkiv in Municipal economy of cities
- Vol. 4 (178) , 206-209
Open AccessFIRE HAZARD OF HYBRID AND ELECTRICAND VEHICLES
In the following time, we received information from many countries of the world about accidents related to fires and explosions of motor vehicles with electric and hybrid vehicles. The popularity of such news is caused by the fact that accidents and fires of cars with internal combustion engines have long become commonplace, which do not attract the attention of the general public. However, many numerous and conducted scientific studies say about the danger of electric and hybrid vehicle models with lithium-ion batteries that they are greatly exaggerated, i.e., damage to the traction battery (battery) can cause a self-destructive chain reaction, but the degree the danger of electrolyte is less than that of gasoline or diesel fuel and much less than that of hydrogen fuel in hybrid modifications. The article examines the causes of the fire hazard of electric and hybrid cars and their consequences. Scientific reasons and innovations regarding the prevention and immediate elimination of short circuits, fires and explosions in the closed space of lithium-ion batteries during the operation of electric hybrid cars are provided. Electric vehicles and hybrids tend to suffer from traction battery technical and other issues. Although a battery flash is dangerous and more difficult to extinguish than a gas flash, the cause of the fire is usually different and these results are found in a defect in the battery pack: "ruptured anode" and "complex separator". The Hyundai Kona and Chevrolet Bolt EV had the most electric vehicle recalls related to fires this year, totaling 152,000 vehicles, while the top two hybrid recalls totaled more than 32,000 vehicles. A lithium-ion type of car catches fire usually not immediately, but after some time. This determines the driver and passengers to immediately leave the interior of the vehicle. When extinguishing a fire, there is a risk of damage to passengers, eyewitnesses and others who are near it by the electric current of high-voltage systems. It is recommended to get out of the interior of the car engulfed in fire and smoke in a timely manner and call the rescuers of the Ministry of Emergency Situations by calling the emergency service. The main task of the firefighters who arrived in the city at the first stage of the event was to disconnect the high-voltage cable using an emergency disconnector or mechanically and to disconnect the high-voltage traction battery. Although the risk of flash in EVs and hybrids exists, it may be receiving a disproportionate amount of attention. It is important for car manufacturers to eliminate the risk of ignition in their vehicles as much as possible, but obviously no form of driving is completely safe. Keywords: hybrid and electricand car, fire, explosion, lithium-ion battery.
- Open Access
- 29 April 2023
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (10 (122)) , 14-21
Comparison of bicoherence on the ensemble of realizations and a selective evaluation of the bispectrum of the dynamics of dangerous parameters of the gas medium during fire
The object of the study is the bicoherence of the bispectrum assessment of the dynamics of dangerous parameters of the gas environment during the ignition of materials. The subject is a measure of bicoherence of the bispectrum estimation from the ensemble of realizations and selective bispectrum estimation for the dynamics of hazardous parameters of the gas environment. The practical importance of the research is the use of the measure of bicoherence of the bispectrum for the early detection of fires. The measure of bicoherence of the dynamics of hazardous parameters of the gas environment is substantiated, which allows them to be numerically compared for the studied bispectrum estimates. As such measure, it is proposed to use the integral value of bicoherence for a given frequency interval, which makes it possible to numerically compare the bicoherence of bispectrum estimates for arbitrary time intervals of the dynamics of hazardous parameters of the gas environment. On the basis of the proposed measure for the frequency range of 0.2–2 Hz, a comparison of the integral bicoherence of the bispectrum estimates was made. The numerical value of the measure was determined for three fixed time intervals of the dynamics of hazardous parameters of the environment, corresponding to the absence of ignition, the occurrence of ignition, and the subsequent burning of test materials in the laboratory chamber. According to the results of the comparison of such values, it was established that the bicoherence of the bispectrum estimation from the ensemble of realizations is the most appropriate for detecting fires. When ignited, the numerical value of the measure for all test materials is about 90°. This means that the nature of the dynamics of hazardous environmental parameters in the event of fires becomes random. In this regard, the proposed measure is recommended to be used as a test for early detection of fires.
- 29 April 2023
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (10 (122)) , 14-21
Open AccessComparison of bicoherence on the ensemble of realizations and a selective evaluation of the bispectrum of the dynamics of dangerous parameters of the gas medium during fire
The object of the study is the bicoherence of the bispectrum assessment of the dynamics of dangerous parameters of the gas environment during the ignition of materials. The subject is a measure of bicoherence of the bispectrum estimation from the ensemble of realizations and selective bispectrum estimation for the dynamics of hazardous parameters of the gas environment. The practical importance of the research is the use of the measure of bicoherence of the bispectrum for the early detection of fires. The measure of bicoherence of the dynamics of hazardous parameters of the gas environment is substantiated, which allows them to be numerically compared for the studied bispectrum estimates. As such measure, it is proposed to use the integral value of bicoherence for a given frequency interval, which makes it possible to numerically compare the bicoherence of bispectrum estimates for arbitrary time intervals of the dynamics of hazardous parameters of the gas environment. On the basis of the proposed measure for the frequency range of 0.2–2 Hz, a comparison of the integral bicoherence of the bispectrum estimates was made. The numerical value of the measure was determined for three fixed time intervals of the dynamics of hazardous parameters of the environment, corresponding to the absence of ignition, the occurrence of ignition, and the subsequent burning of test materials in the laboratory chamber. According to the results of the comparison of such values, it was established that the bicoherence of the bispectrum estimation from the ensemble of realizations is the most appropriate for detecting fires. When ignited, the numerical value of the measure for all test materials is about 90°. This means that the nature of the dynamics of hazardous environmental parameters in the event of fires becomes random. In this regard, the proposed measure is recommended to be used as a test for early detection of fires.
- Open Access
- 28 February 2023
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 1 (6 (121)) , 33-39
Development of technology for obtaining fat compositions with increased oxidative stability
The object of research is the process of fat oxidation at elevated and standard temperatures. Fats are used in chemical, pharmaceutical, food and other industries. Oxidative deterioration changes the composition of fats, reduces the efficiency of chemical reactions involving fats and the quality of final products. An urgent task is to increase the oxidative stability of fats. The oxidative stability of fat compositions based on rapeseed, high-oleic sunflower and palm oils by the induction period at a temperature of 110 °C was investigated. The induction periods of the initial oils were 408.48 min., 795.87 min. and 630.2 min., respectively. Rational ratios of oils in the compositions were found: high-oleic sunflower: palm (50:50) %; rapeseed: high-oleic sunflower: palm (16.67:66.67:16.67) %; rapeseed: high-oleic sunflower: palm (33.33:33.33:33.33) %. The induction periods of the mixtures are 650.57 min., 710.56 min. and 670.56 min., respectively. The increase in the oxidative stability of the developed compositions using the mixture of synthetic antioxidants (butylhydroxyanisole, butylhydroxytoluene and tert-butylhydroquinone) in an amount of 300 mg/kg of fat mixture was studied. The induction periods of the developed compositions were 910.80 min., 1279.01 min. and 1072.90 min., respectively. The physicochemical parameters of compositions with the addition of antioxidants after 5 months of storage at a temperature of (20±2) °C were determined. The peroxide values of the compositions were 5.65; 3.28; 4.50 ½ O mmol/kg, respectively. The research results make it possible to produce fats with increased oxidative stability and necessary properties, to predict induction periods of fat compositions depending on the concentrations of components. This will increase the profitability of production and the quality of fats obtained
- 28 February 2023
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 1 (6 (121)) , 33-39
Open AccessDevelopment of technology for obtaining fat compositions with increased oxidative stability
The object of research is the process of fat oxidation at elevated and standard temperatures. Fats are used in chemical, pharmaceutical, food and other industries. Oxidative deterioration changes the composition of fats, reduces the efficiency of chemical reactions involving fats and the quality of final products. An urgent task is to increase the oxidative stability of fats. The oxidative stability of fat compositions based on rapeseed, high-oleic sunflower and palm oils by the induction period at a temperature of 110 °C was investigated. The induction periods of the initial oils were 408.48 min., 795.87 min. and 630.2 min., respectively. Rational ratios of oils in the compositions were found: high-oleic sunflower: palm (50:50) %; rapeseed: high-oleic sunflower: palm (16.67:66.67:16.67) %; rapeseed: high-oleic sunflower: palm (33.33:33.33:33.33) %. The induction periods of the mixtures are 650.57 min., 710.56 min. and 670.56 min., respectively. The increase in the oxidative stability of the developed compositions using the mixture of synthetic antioxidants (butylhydroxyanisole, butylhydroxytoluene and tert-butylhydroquinone) in an amount of 300 mg/kg of fat mixture was studied. The induction periods of the developed compositions were 910.80 min., 1279.01 min. and 1072.90 min., respectively. The physicochemical parameters of compositions with the addition of antioxidants after 5 months of storage at a temperature of (20±2) °C were determined. The peroxide values of the compositions were 5.65; 3.28; 4.50 ½ O mmol/kg, respectively. The research results make it possible to produce fats with increased oxidative stability and necessary properties, to predict induction periods of fat compositions depending on the concentrations of components. This will increase the profitability of production and the quality of fats obtained
- Open Access
- 29 June 2022
- Published by Kharkiv National Automobile and Highway University in Vehicle and Electronics. Innovative Technologies
- No. 21,p. 40-47
Electromagnetic radiation of hybrid vehicles
Problem. As a result of automobile traffic every year 20-30% of the territory of cities are subject to electromagnetic pollution in cities and settlements. This is due to the increase in power and number of electrical equipment of each individual car. The urgency of the problem of electromagnetic pollution is an important step in determining the impact of electromagnetic radiation on humans in the rapid development of hybrid cars. Goal. The aim of this work is to determine the effect of electromagnetic radiation on humans in the conditions of rapid development of hybrid cars. To achieve this goal, it is necessary to solve the following tasks: review anthropogenic electromagnetic fields; find the elements of the electromagnetic field in a hybrid car; consider the most common methods of protection against electromagnetic fields. Methodology. The article presents a general classification of electromagnetic radiation to humans arising in hybrid vehicles. It is extremely important to reveal the phenomena occurring in hybrid cars in the research work to find the truth and the processes of occurrence of electromagnetic radiation. This issue is given primary importance, because finding effective technical, environmental and other methods and means of protecting people in hybrid and other vehicles is extremely necessary and in demand at the present stage. Thus, based on the characteristics of the material and aspects of its analysis determined the structure of the text in which some of the facts are given using the information available in the attached literature. Results. The result of the work were the proposed methods of shielding high-frequency and low-frequency levels based on physical properties – the reflection and absorption of electromagnetic waves during the transition from one medium to another. Originality. Methods of studying the effect of electromagnetic radiation on a person in vehicles (automotive, hybrid, electric) and especially on the reaction of a biological cell, its vital activity, require in-depth research to determine criteria, acceptable standards and optimal methods of protection against EMF and EMI. Practical value. The practical significance of this study is focused on readers and researchers of vehicles (automotive, hybrid, electric) which are interested in the negative effects of electromagnetic radiation, protection of passengers and drivers from them. The impact of electromagnetic radiation from hybrid and other types of vehicles on humans is a necessary task not only for scientists but also for manufacturers of these modes of transport, who for unknown reasons are trying to "freeze" the proposals and technical solutions offered by the World Scientific Society.
- 29 June 2022
- Published by Kharkiv National Automobile and Highway University in Vehicle and Electronics. Innovative Technologies
- No. 21,p. 40-47
Open AccessElectromagnetic radiation of hybrid vehicles
Problem. As a result of automobile traffic every year 20-30% of the territory of cities are subject to electromagnetic pollution in cities and settlements. This is due to the increase in power and number of electrical equipment of each individual car. The urgency of the problem of electromagnetic pollution is an important step in determining the impact of electromagnetic radiation on humans in the rapid development of hybrid cars. Goal. The aim of this work is to determine the effect of electromagnetic radiation on humans in the conditions of rapid development of hybrid cars. To achieve this goal, it is necessary to solve the following tasks: review anthropogenic electromagnetic fields; find the elements of the electromagnetic field in a hybrid car; consider the most common methods of protection against electromagnetic fields. Methodology. The article presents a general classification of electromagnetic radiation to humans arising in hybrid vehicles. It is extremely important to reveal the phenomena occurring in hybrid cars in the research work to find the truth and the processes of occurrence of electromagnetic radiation. This issue is given primary importance, because finding effective technical, environmental and other methods and means of protecting people in hybrid and other vehicles is extremely necessary and in demand at the present stage. Thus, based on the characteristics of the material and aspects of its analysis determined the structure of the text in which some of the facts are given using the information available in the attached literature. Results. The result of the work were the proposed methods of shielding high-frequency and low-frequency levels based on physical properties – the reflection and absorption of electromagnetic waves during the transition from one medium to another. Originality. Methods of studying the effect of electromagnetic radiation on a person in vehicles (automotive, hybrid, electric) and especially on the reaction of a biological cell, its vital activity, require in-depth research to determine criteria, acceptable standards and optimal methods of protection against EMF and EMI. Practical value. The practical significance of this study is focused on readers and researchers of vehicles (automotive, hybrid, electric) which are interested in the negative effects of electromagnetic radiation, protection of passengers and drivers from them. The impact of electromagnetic radiation from hybrid and other types of vehicles on humans is a necessary task not only for scientists but also for manufacturers of these modes of transport, who for unknown reasons are trying to "freeze" the proposals and technical solutions offered by the World Scientific Society.
- Open Access
- 25 February 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 1 (10(115)) , 31-40
Devising a procedure to forecast the level of chemical damage to the atmosphere during active deposition of dangerous gases
This paper reports a procedure devised to forecast the level of chemical pollution of the atmosphere, which includes a mathematical model for the distribution of the concentration of dangerous gas in the atmosphere at its active deposition by dispersed jets of liquid, as well as a technique for its implementation. Based on the differential equations of gas distribution in space, a phased model of the propagation of a cloud of a dangerous chemical substance was built. The model describes stages in the discharge of a dangerous gaseous substance from emergency technological equipment, the deposition of dangerous gas by a finely-dispersed flow, and free propagation of the cloud in the air. The reported mathematical model makes it possible to calculate the size of pollution zones while determining the boundary safety conditions. When forecasting, the main meteorological parameters, the width of the deposition zone, and the chemical properties of both the gas and liquid are taken into consideration. The comparative analysis of the results of forecasting a conditional zone of chemical damage with the free propagation of the cloud, and at the active deposition by precipitation or technical devices, was carried out. The simulation results revealed that with an increase in the wind speed from 1 m/s to 5 m/s, the size of the affected area increases by 2.7 times, while the concentration of dangerous gas in the cloud falls by 2.5‒3 times. An algorithm has been proposed for integrating the devised methodology of forecasting the level of chemical pollution of the atmosphere into a general cycle of emergency management. It should be especially noted that the devised procedure contains the entire range of components that are necessary for its practical application. It includes a description of the procedure and practical recommendations for the use of the proposed technique in the elimination of emergencies, as well as a list of probable events when the use of the developed procedure would be most effective.
- 25 February 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 1 (10(115)) , 31-40
Open AccessDevising a procedure to forecast the level of chemical damage to the atmosphere during active deposition of dangerous gases
This paper reports a procedure devised to forecast the level of chemical pollution of the atmosphere, which includes a mathematical model for the distribution of the concentration of dangerous gas in the atmosphere at its active deposition by dispersed jets of liquid, as well as a technique for its implementation. Based on the differential equations of gas distribution in space, a phased model of the propagation of a cloud of a dangerous chemical substance was built. The model describes stages in the discharge of a dangerous gaseous substance from emergency technological equipment, the deposition of dangerous gas by a finely-dispersed flow, and free propagation of the cloud in the air. The reported mathematical model makes it possible to calculate the size of pollution zones while determining the boundary safety conditions. When forecasting, the main meteorological parameters, the width of the deposition zone, and the chemical properties of both the gas and liquid are taken into consideration. The comparative analysis of the results of forecasting a conditional zone of chemical damage with the free propagation of the cloud, and at the active deposition by precipitation or technical devices, was carried out. The simulation results revealed that with an increase in the wind speed from 1 m/s to 5 m/s, the size of the affected area increases by 2.7 times, while the concentration of dangerous gas in the cloud falls by 2.5‒3 times. An algorithm has been proposed for integrating the devised methodology of forecasting the level of chemical pollution of the atmosphere into a general cycle of emergency management. It should be especially noted that the devised procedure contains the entire range of components that are necessary for its practical application. It includes a description of the procedure and practical recommendations for the use of the proposed technique in the elimination of emergencies, as well as a list of probable events when the use of the developed procedure would be most effective.