Arif Wahjudi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Arif Wahjudi has a total of 49 co-authors. Here are the top co-authors by number of shared publications:
- I. Made Londen Batan
Institut Teknologi Sepuluh Nopember
9 shared publications - Agus Sigit Pramono
Institut Teknologi Sepuluh Nopember
7 shared publications - Ahmad Anas Arifin
Department of Mechanical Engineering, Institut Teknologi Sepuluh Nopember, Indonesia
4 shared publications - Michele Bici
Sapienza University of Rome
4 shared publications - Adi Susanto
Institut Teknologi Sepuluh Nopember
2 shared publications Faisal Ibrahim
2 shared publications
Latest Publications
- Open Access
- 26 July 2026
- Published by Elsevier in SSRN Electronic Journal
Ergonomic Design and Evaluation of an Operation Table Using the Rapid Upper Limb Assessment (RULA) Method
Operating tables should facilitate safe patient positioning and support suitable working postures for medical personnel of different body sizes. This study developed an adjustable operating table with ergonomic assessment, structural verification and stability testing. The table was 2.0 m in length, 0.7 m in width and had an electrically actuated height range of 75–105 cm, controlled by push buttons. It was mainly structured from Al 6061-T aluminum alloy. The ergonomic performance was evaluated based on the Rapid Upper Limb Assessment (RULA) method using CATIA V5. Stability was assessed at loads of 0, 20, 40, 60.5, 82.7, and 100 kg and table heights from 75 to 105 cm with three repetitions per condition and response surface analysis. Verifying structure under 120 kg load showed maximum von Mises stress to be 14.6 MPa, well below allowable stress of 179 MPa. The most stable condition predicted was at 75 cm and 0 kg with pitch, roll and translational deviation values of 0.518°, 0.773° and 2.066 mm, respectively. The least stable condition was 105 cm and 86.76 kg with corresponding values of 2.305°, 3.311° and 5.340 mm respectively. The most important factor for stability was the loading condition. The RULA scores ranged from 3 to 4 and a table height of 85–90 cm gave the best compromise between ergonomic suitability and mechanical stability. The present results confirm the structural safety, mechanical stability and ergonomic acceptability of the proposed table in the recommended operating range.
- 26 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessErgonomic Design and Evaluation of an Operation Table Using the Rapid Upper Limb Assessment (RULA) Method
Operating tables should facilitate safe patient positioning and support suitable working postures for medical personnel of different body sizes. This study developed an adjustable operating table with ergonomic assessment, structural verification and stability testing. The table was 2.0 m in length, 0.7 m in width and had an electrically actuated height range of 75–105 cm, controlled by push buttons. It was mainly structured from Al 6061-T aluminum alloy. The ergonomic performance was evaluated based on the Rapid Upper Limb Assessment (RULA) method using CATIA V5. Stability was assessed at loads of 0, 20, 40, 60.5, 82.7, and 100 kg and table heights from 75 to 105 cm with three repetitions per condition and response surface analysis. Verifying structure under 120 kg load showed maximum von Mises stress to be 14.6 MPa, well below allowable stress of 179 MPa. The most stable condition predicted was at 75 cm and 0 kg with pitch, roll and translational deviation values of 0.518°, 0.773° and 2.066 mm, respectively. The least stable condition was 105 cm and 86.76 kg with corresponding values of 2.305°, 3.311° and 5.340 mm respectively. The most important factor for stability was the loading condition. The RULA scores ranged from 3 to 4 and a table height of 85–90 cm gave the best compromise between ergonomic suitability and mechanical stability. The present results confirm the structural safety, mechanical stability and ergonomic acceptability of the proposed table in the recommended operating range.
- Open Access
- 7 May 2026
- Published by Elsevier in SSRN Electronic Journal
A Multi-Criteria Framework for Optimizing Drilling Conditions in AFRP Composites based on a BPNN-GA Intelligent Framework
Aramid Fiber Reinforced Polymer (AFRP) composites are increasingly adopted in automotive lightweight structures for their excellent mechanical performance. Precision drilling remains indispensable in component assembly, where maintaining superior hole integrity is a critical requirement. This study introduces an AI-driven multi-objective optimization framework to minimize thrust force, torque, peel-up and push-out delamination damage during AFRP drilling. A two-replication full factorial design was employed, varying drill type, spindle speed, and feed rate to generate a comprehensive dataset for analysis. A Backpropagation Neural Network (BPNN) was constructed to evaluate and predict the complex connection between process parameters and multiple responses. The integration of a Backpropagation Neural Network (BPNN) with a Genetic Algorithm (GA) enabled efficient identification of the optimal drilling parameter set. Verification experiments confirmed that drilling with a twist drill at 1455 rpm and 10 mm/min achieved the lowest thrust (29.03 N), torque (90.33 Nmm), and delamination factors (peel-up: 1.157, push-out: 1.081). This hybrid BPNN–GA framework demonstrates an effective AI-driven strategy for achieving sustainable and high-precision machining of AFRP composites.
- 7 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessA Multi-Criteria Framework for Optimizing Drilling Conditions in AFRP Composites based on a BPNN-GA Intelligent Framework
Aramid Fiber Reinforced Polymer (AFRP) composites are increasingly adopted in automotive lightweight structures for their excellent mechanical performance. Precision drilling remains indispensable in component assembly, where maintaining superior hole integrity is a critical requirement. This study introduces an AI-driven multi-objective optimization framework to minimize thrust force, torque, peel-up and push-out delamination damage during AFRP drilling. A two-replication full factorial design was employed, varying drill type, spindle speed, and feed rate to generate a comprehensive dataset for analysis. A Backpropagation Neural Network (BPNN) was constructed to evaluate and predict the complex connection between process parameters and multiple responses. The integration of a Backpropagation Neural Network (BPNN) with a Genetic Algorithm (GA) enabled efficient identification of the optimal drilling parameter set. Verification experiments confirmed that drilling with a twist drill at 1455 rpm and 10 mm/min achieved the lowest thrust (29.03 N), torque (90.33 Nmm), and delamination factors (peel-up: 1.157, push-out: 1.081). This hybrid BPNN–GA framework demonstrates an effective AI-driven strategy for achieving sustainable and high-precision machining of AFRP composites.
- 1 May 2026
- Published by Springer Nature
- p. 79-101
Numerical Investigation of the Thermal Performance of Lattice Structures
- 1 May 2026
- Published by Springer Nature
- p. 79-101
Numerical Investigation of the Thermal Performance of Lattice Structures
- 1 March 2026
- Published by Kyushu University in Evergreen
- Vol. 13 (1) , 373-386
Optimization of Surface Roughness and Diameter Error in Thin-Walled AA6063 during Internal Turning under Minimum Quantity Lubrication
- 1 March 2026
- Published by Kyushu University in Evergreen
- Vol. 13 (1) , 373-386
Optimization of Surface Roughness and Diameter Error in Thin-Walled AA6063 during Internal Turning under Minimum Quantity Lubrication
- Open Access
- 28 February 2026
- Published by Universitas Negeri Padang in Teknomekanik
- Vol. 9 (1) , 1-24
Comparative analysis of bio-inspired and topology-optimized lattices under compressive loading
Lattice structure design is still dominated by strut-based forms and surface-based shapes, such as triply periodic minimal surfaces (TPMS), which both exhibit overlapping limitations. Strut lattices often show strong anisotropy because their response depends heavily on cell orientation, while TPMS lattices are difficult to adjust when bounded by geometric constraints. These conditions eventually led to stagnation in the development of lattice morphology. Hybrid and topology-optimization methods have appeared as possible alternatives, but many of them still produce modified versions of classical patterns. This study examined two lattice geometries: the Pyramorph, inspired by the shape of a pyramid, and the Topomorph, generated through a topology optimization framework. Both structures were designed using a CAD unit cell patterning technique and manufactured using the FDM method, with relative densities ranging from 0.40 to 0.44. Their mechanical behaviour was examined through FEA simulation and uniaxial compression testing. The parameter variations included cell orientations of 0°, 15°, 30°, and 45°, and cell sizes of 8 mm and 12 mm within a 24 mm specimen. The Topomorph showed superior strength, reaching 15–20 MPa, while the Pyramorph reached only 7–8 MPa. The highest value, about 20.5 MPa, was obtained from the Topomorph at 0° and with an 8 mm cell size. Failure modes indicated buckling and delamination in the Pyramorph, while the Topomorph tended to collapse progressively. These findings indicate that topology optimization combined with CAD-based patterning could significantly improve lattice performance.
- 28 February 2026
- Published by Universitas Negeri Padang in Teknomekanik
- Vol. 9 (1) , 1-24
Open AccessComparative analysis of bio-inspired and topology-optimized lattices under compressive loading
Lattice structure design is still dominated by strut-based forms and surface-based shapes, such as triply periodic minimal surfaces (TPMS), which both exhibit overlapping limitations. Strut lattices often show strong anisotropy because their response depends heavily on cell orientation, while TPMS lattices are difficult to adjust when bounded by geometric constraints. These conditions eventually led to stagnation in the development of lattice morphology. Hybrid and topology-optimization methods have appeared as possible alternatives, but many of them still produce modified versions of classical patterns. This study examined two lattice geometries: the Pyramorph, inspired by the shape of a pyramid, and the Topomorph, generated through a topology optimization framework. Both structures were designed using a CAD unit cell patterning technique and manufactured using the FDM method, with relative densities ranging from 0.40 to 0.44. Their mechanical behaviour was examined through FEA simulation and uniaxial compression testing. The parameter variations included cell orientations of 0°, 15°, 30°, and 45°, and cell sizes of 8 mm and 12 mm within a 24 mm specimen. The Topomorph showed superior strength, reaching 15–20 MPa, while the Pyramorph reached only 7–8 MPa. The highest value, about 20.5 MPa, was obtained from the Topomorph at 0° and with an 8 mm cell size. Failure modes indicated buckling and delamination in the Pyramorph, while the Topomorph tended to collapse progressively. These findings indicate that topology optimization combined with CAD-based patterning could significantly improve lattice performance.
- 17 March 2025
- Published by Springer Nature
- p. 45-53
Isotropic Body-Centered Cubic (BCC) Lattice Structure Design
- 17 March 2025
- Published by Springer Nature
- p. 45-53
Isotropic Body-Centered Cubic (BCC) Lattice Structure Design
- 18 February 2025
- Published by Springer Nature
- p. 363-370
Fuzzy PID Control for Parallel Friction Stir Welding Robot Manipulator
- 18 February 2025
- Published by Springer Nature
- p. 363-370
Fuzzy PID Control for Parallel Friction Stir Welding Robot Manipulator
- Open Access
- 12 January 2025
- Published by Universitas Muhammadiyah Magelang in Mechanical Engineering for Society and Industry
- Vol. 5 (1) , 245-256
Investigation of discrepancies in isotropic material and structural properties in lattice frameworks
Lattice structures have developed as a vital component in advanced engineering applications due to their superior strength-to-weight ratios and adjustable mechanical properties. This paper focuses on examining the correlation between the isotropic features of lattices at the material level and their structural performance. The research used near-isotropic Crossing-cylinder (CC)- Body Centered Cubic (BCC) cells in various orientations and sizes. Both experimental analysis and finite element analysis were used to examine the compressive strength of the structure in each orientation. The results reveal that cell orientation is important for determining failure modes and mechanical performance at the structural level. At 0°, the lattice has higher compressive strength and energy absorption due to effective load transfer via CC-aligned struts. In contrast, higher orientations (e.g., 15°, 30°, and 45°) are dominated by collapse-type failures, indicating anisotropic behavior in an otherwise isotropic design. Smaller cell sizes have more strength at lower orientations due to their higher relative density, but larger cells perform better at higher orientations.
- 12 January 2025
- Published by Universitas Muhammadiyah Magelang in Mechanical Engineering for Society and Industry
- Vol. 5 (1) , 245-256
Open AccessInvestigation of discrepancies in isotropic material and structural properties in lattice frameworks
Lattice structures have developed as a vital component in advanced engineering applications due to their superior strength-to-weight ratios and adjustable mechanical properties. This paper focuses on examining the correlation between the isotropic features of lattices at the material level and their structural performance. The research used near-isotropic Crossing-cylinder (CC)- Body Centered Cubic (BCC) cells in various orientations and sizes. Both experimental analysis and finite element analysis were used to examine the compressive strength of the structure in each orientation. The results reveal that cell orientation is important for determining failure modes and mechanical performance at the structural level. At 0°, the lattice has higher compressive strength and energy absorption due to effective load transfer via CC-aligned struts. In contrast, higher orientations (e.g., 15°, 30°, and 45°) are dominated by collapse-type failures, indicating anisotropic behavior in an otherwise isotropic design. Smaller cell sizes have more strength at lower orientations due to their higher relative density, but larger cells perform better at higher orientations.
- Open Access
- 3 July 2024
- Published by Knowledge E DMCC in KnE Social Sciences
- p. 35–48
Numerical Study of Optimal Combustion in Tangentially Fired Coal Boiler 625 MW by Considering Rear Pass Temperature
Tangentially fired boilers have a burner system within a single actuator group and a SOFA system that controls the fuel and air distribution to generate boiler combustion in the furnace. The goal of this study was to determine optimal combustion by statistically examining the effect of changes in the burner and SOFA angles on the response of rear pass boiler temperature and NOx concentration in tangentially burned boilers. (1) Tilting burner angles of +30⁰, +15⁰, 0⁰, –15⁰, and –30⁰, and (2) SOFA tilting and yawing angles of –15⁰, –8⁰, 0⁰, +8⁰, +15⁰ were used in this study. The GA (Genetic Algorithm) approach and CFD software were utilized to optimize the rear pass temperature and NOx content response. The simulation results data were then examined using ANOVA, and it was discovered that tilting burner and tilting SOFA have a substantial effect on response, however, yaw SOFA does not. In this scenario, the resulting angle variations for tilting burner, SOFA-tilt, and SOFA-yaw are +11⁰, –15⁰, and 2⁰, respectively. The optimal angle adjustments result in rear pass temperatures of 821.33 ⁰K and 816.27 ⁰K, with a slight fluctuation of 5.06 ⁰K. This was in contrast to the preceding conditions, when the rear pass temperatures of sides A and B were 781.32 ⁰K and 767.83 ⁰K, respectively, resulting in a 13.49 ⁰K difference. Keywords: tilting burner, tilting and yawing SOFA, rear pass temperature, NOx, GA and CFD method
- 3 July 2024
- Published by Knowledge E DMCC in KnE Social Sciences
- p. 35–48
Open AccessNumerical Study of Optimal Combustion in Tangentially Fired Coal Boiler 625 MW by Considering Rear Pass Temperature
Tangentially fired boilers have a burner system within a single actuator group and a SOFA system that controls the fuel and air distribution to generate boiler combustion in the furnace. The goal of this study was to determine optimal combustion by statistically examining the effect of changes in the burner and SOFA angles on the response of rear pass boiler temperature and NOx concentration in tangentially burned boilers. (1) Tilting burner angles of +30⁰, +15⁰, 0⁰, –15⁰, and –30⁰, and (2) SOFA tilting and yawing angles of –15⁰, –8⁰, 0⁰, +8⁰, +15⁰ were used in this study. The GA (Genetic Algorithm) approach and CFD software were utilized to optimize the rear pass temperature and NOx content response. The simulation results data were then examined using ANOVA, and it was discovered that tilting burner and tilting SOFA have a substantial effect on response, however, yaw SOFA does not. In this scenario, the resulting angle variations for tilting burner, SOFA-tilt, and SOFA-yaw are +11⁰, –15⁰, and 2⁰, respectively. The optimal angle adjustments result in rear pass temperatures of 821.33 ⁰K and 816.27 ⁰K, with a slight fluctuation of 5.06 ⁰K. This was in contrast to the preceding conditions, when the rear pass temperatures of sides A and B were 781.32 ⁰K and 767.83 ⁰K, respectively, resulting in a 13.49 ⁰K difference. Keywords: tilting burner, tilting and yawing SOFA, rear pass temperature, NOx, GA and CFD method