BNBilal J. Noman

Bilal J. Noman

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Bilal J. Noman has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Impact of Vertical Vibration on Group Piles During Earthquake Loading: Experimental Findings

    by Bilal J. Noman, Bushra S. Albusoda

    This study presents novel research on the impact of vertical vibration on the dynamic response of pile groups embedded in stratified soil under seismic loading conditions. An experimental setup was employed wherein the piled machine foundation was subjected to vertical vibrations at three operating frequencies (10, 20, and 30 Hz) and subsequently exposed to four levels of seismic acceleration (0.1 g, 0.34 g, 0.77 g, and 0.82 g). Piles with a length-to-diameter ratio of 25 were embedded in a stratified soil profile, with an upper loose layer (30% relative density) and a lower dense layer (80% relative density) acting as end-bearing. Measurements and analyses of horizontal and vertical accelerations, and amplification factors were conducted using the Fast Fourier Transform (FFT), spectral acceleration (Sa), and variation of acceleration with depth. The results demonstrated a significant reduction in horizontal acceleration, with a peak ground acceleration (PGA) reduction of up to 64% in average, particularly at higher frequencies such as 30 Hz. The mitigation efficiency at 30Hz improved with increasing PGA, showing reductions of 42, 68, 75, and 63% for seismic accelerations of 0.1 g, 0.34 g, 0.77 g, and 0.82 g, respectively. The analysis further revealed harmonic resonance and higher mode effects at lower frequencies, with nonlinear soil behavior affecting the resonance and amplification patterns. Additionally, the results demonstrate that the far-field accelerations exceeded the near-field accelerations within the pile group, particularly in the surface layer. The results indicated that the initial vibration amplitudes exceeded the safe operating limits outlined in ACI 351.3R-18 under seismic loading, particularly at higher seismic acceleration levels and lower frequencies. Additional modified charts were presented to account for these conditions. The results presented promising evidence for using vertical vibrations as an earthquake-mitigation strategy. However, avoiding operating at frequencies less than 10 Hz is recommended because of the potential resonance and interaction with horizontal accelerations during earthquakes. Doi: 10.28991/CEJ-SP2024-010-010 Full Text: PDF


  • Numerical Analysis of Piles Group Surrounded by Grouting Under Seismic Load

    by Mahdi O. Karkush, Abeer H. Mohsin, Husam M. Saleh, Bilal J. Noman


  • Open Access

    Seismic Analysis of Floating Stone Columns in Soft Clayey Soil

    by Mahdi O. Karkush, Amer G. Jihad, Karrar A. Jawad, Mustafa S. Ali, Bilal J. Noman

    The response of floating stone columns of different lengths to diameter ratio (L/D = 0, 2, 4, 6, 8, and 10) ratios exposed to earthquake excitations is well modeled in this paper. Such stone column behavior is essential in the case of lateral displacement under an earthquake through the soft clay soil. ABAQUS software was used to simulate the behavior of stone columns in soft clayey soil using an axisymmetric finite element model. The behavior of stone column material has been modeled with a Drucker-Prager model. The soft soil material was modeled by the Mohr-Coulomb failure criterion assuming an elastic-perfectly plastic behavior. The floating stone columns were subjected to the El Centro earthquake, which had a magnitude of 7.1 and a peak ground acceleration of 3.50 m/s2. The surface displacement, velocity, and acceleration in soft clayey enhanced by floating stone columns are also smaller than in natural soft clay. The findings of this research revealed that under the influence of earthquake waves, lateral displacement varies with stone columns of various lengths.


  • Open Access

    Effect of Using Different Aspect Ratio of Longitudinal Steel Plates in Reinforced Concrete Beams

    by Khalid I. Qaddoory, Ahmed A. Mansor, Ahlam S. Mohammed, Bilal J. Noman

    In the past few years, new techniques have emerged using steel plates instead of traditional reinforcement in the reinforced concrete beams. This study deals with using a new method for reinforced concrete beams using steel plates instead of traditional steel bars with different thicknesses of (4, 5, and 6 mm) placed vertically inside the lower part of the beam. Four reinforced concrete beams were cast and tested under a two-point load. All beams had the same cross-sectional area of reinforcement and dimensions of 2100 mm in length, 350 mm in height, and 250 in width. The results showed that as the thickness of the steel plate increases, the samples would have greater resistance until more deflection is produced. In addition, there is a reduction in the crack load, ultimate load, and yield load when replacing reinforcing bars with steel plates. In which, a reduction in crack load by about 11.1, 15.5, and 22.2% plate thicknesses of 4,5,6 mm respectively, compared to reference beam that had a deformed steel bar (Dia. 16 mm). In addition, a reduction in yielding load was observed about 42, 53, and 60% for steel plate thickness of 4, 5, and 6 mm respectively, compared to the reference model. Finally, the cracks for all the steel plate specimens compared to reference specimens were wider and smaller.