Chuntai Zheng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Chuntai Zheng has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
- Xin Zhang
The Hong Kong University of Science and Technology
7 shared publications - Peng Zhou
Division of Integrative Systems and Design, The Hong Kong University of Science and Technology 4 , Clear Water Bay, Kowloon, Hong Kong Special Administrative Region
6 shared publications - Siyang Zhong
Department of Aeronautical and Aviation Engineering, The Hong Kong Polytechnic University, Kowloon, China
3 shared publications - Han Wu
The Hong Kong Polytechnic University
2 shared publications Keke Gao
2 shared publicationsLei Zhong
2 shared publications
Latest Publications
- 12 August 2026
- Published by Walter de Gruyter GmbH in Transport Phenomena
- Vol. 1 (3)
Turbulence enhancement with a fan array wind generator using geometrically textured actuation and particle swarm optimization
Fan array wind generators (FAWG) are designed to generate a rich set of turbulent flows reminiscent of those found in natural environments. In this study, we experimentally investigate a square FAWG consisting of 10 × 10 individually controllable fans with 4 cm width and a maximum velocity of 17 m/s. The goal is to maximize the turbulence intensity in the test region. Two approaches for fan operation are investigated: first, geometric texturing of the duty cycle distribution, and second, maximization of the turbulence intensity at selected hot-wire sensors with particle-swarm optimization (PSO). We find that geometric texturing, specifically a checkerboard pattern of active fans, yields a nearly uniform turbulence field driven by jet interactions with turbulence levels around 0.14. However, particle swarm optimization doubles this local turbulence level yielding 0.28 at the chosen sensor locations but sacrifices performance elsewhere. A physical analysis reveals that particle swarm location places the sensors in the shear-layer between active and inactive regions while geometric texturing exploits the large fluctuation at the end of the potential core of the active patches. This region marks the maximum achievable turbulence level. The proposed physical interpretation of texture-based turbulence enhancement is corroborated with a square 40 × 40 fan array wind generator (Guinness World Record 2025) with a width of 3.25 m. Texture-based turbulence control opens a promising avenue to simultaneously command the mean velocity profile and the turbulence level field of a sufficiently large fan array wind generator.
- 12 August 2026
- Published by Walter de Gruyter GmbH in Transport Phenomena
- Vol. 1 (3)
Turbulence enhancement with a fan array wind generator using geometrically textured actuation and particle swarm optimization
Fan array wind generators (FAWG) are designed to generate a rich set of turbulent flows reminiscent of those found in natural environments. In this study, we experimentally investigate a square FAWG consisting of 10 × 10 individually controllable fans with 4 cm width and a maximum velocity of 17 m/s. The goal is to maximize the turbulence intensity in the test region. Two approaches for fan operation are investigated: first, geometric texturing of the duty cycle distribution, and second, maximization of the turbulence intensity at selected hot-wire sensors with particle-swarm optimization (PSO). We find that geometric texturing, specifically a checkerboard pattern of active fans, yields a nearly uniform turbulence field driven by jet interactions with turbulence levels around 0.14. However, particle swarm optimization doubles this local turbulence level yielding 0.28 at the chosen sensor locations but sacrifices performance elsewhere. A physical analysis reveals that particle swarm location places the sensors in the shear-layer between active and inactive regions while geometric texturing exploits the large fluctuation at the end of the potential core of the active patches. This region marks the maximum achievable turbulence level. The proposed physical interpretation of texture-based turbulence enhancement is corroborated with a square 40 × 40 fan array wind generator (Guinness World Record 2025) with a width of 3.25 m. Texture-based turbulence control opens a promising avenue to simultaneously command the mean velocity profile and the turbulence level field of a sufficiently large fan array wind generator.
- 1 December 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (12)
Experimental investigation into pressure oscillations in the compression chamber of a rotary compressor
This study experimentally investigates the characteristics of the pressure oscillations within the compression chamber of a rotary compressor and evaluates their impact on compressor performance. Four fast-response pressure transducers are installed at circumferential positions in the upper cylinder to measure instantaneous pressure under varying rotational speeds (60–120 Hz) and suction pressures (0.4–1.0 MPa). Results reveal significant pressure oscillations during compression, with amplitudes increasing at higher rotational speeds. The oscillation frequency ranges from below 1000 Hz at the start of compression to approximately 4000 Hz near discharge. A finite element study is conducted to calculate the natural frequencies of the compression chamber assuming the shape at an instantaneous shaft angle. The calculated frequencies are identical to those observed in the experiments. It is revealed that the physical mechanisms of the pressure oscillations are the quasi-static acoustic resonance within the crescent-shaped chamber. Rapid volume changes with fast roller motions are identified as key triggers for the resonance. Performance tests demonstrate a decline in the coefficient of performance (COP) with increasing speed. The study highlights that acoustic resonance-induced pressure oscillations critically degrade energy efficiency, particularly at elevated rotational speeds. Mitigating these oscillations is essential for optimizing compressor performance at high speeds.
- 1 December 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (12)
Experimental investigation into pressure oscillations in the compression chamber of a rotary compressor
This study experimentally investigates the characteristics of the pressure oscillations within the compression chamber of a rotary compressor and evaluates their impact on compressor performance. Four fast-response pressure transducers are installed at circumferential positions in the upper cylinder to measure instantaneous pressure under varying rotational speeds (60–120 Hz) and suction pressures (0.4–1.0 MPa). Results reveal significant pressure oscillations during compression, with amplitudes increasing at higher rotational speeds. The oscillation frequency ranges from below 1000 Hz at the start of compression to approximately 4000 Hz near discharge. A finite element study is conducted to calculate the natural frequencies of the compression chamber assuming the shape at an instantaneous shaft angle. The calculated frequencies are identical to those observed in the experiments. It is revealed that the physical mechanisms of the pressure oscillations are the quasi-static acoustic resonance within the crescent-shaped chamber. Rapid volume changes with fast roller motions are identified as key triggers for the resonance. Performance tests demonstrate a decline in the coefficient of performance (COP) with increasing speed. The study highlights that acoustic resonance-induced pressure oscillations critically degrade energy efficiency, particularly at elevated rotational speeds. Mitigating these oscillations is essential for optimizing compressor performance at high speeds.
- 24 December 2024
- Published by Elsevier in Applied Thermal Engineering
- Vol. 263
Performance analysis for a rotary compressor at high speed: Experimental study and mathematical modeling
- 24 December 2024
- Published by Elsevier in Applied Thermal Engineering
- Vol. 263
Performance analysis for a rotary compressor at high speed: Experimental study and mathematical modeling
- Open Access
- 1 January 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (1)
On the evolution of flow structures around a track cyclist
In this study, flow structures and their evolution over a track cyclist were investigated through wind tunnel tests. In supplement to the experiment, high-fidelity numerical simulations were also conducted to demonstrate the origins of global flow structures. In wind tunnel tests, a full-scale track cyclist mannequin was built based on the three-dimensional scanning of an elite track cyclist in a riding position of a sprint event, and a Cobra probe was used to measure the wake structures. The results show that the preeminent flow structures around the track cyclist mannequin are the streamwise vortices originating from different body parts. The evolution of these vortices involves strong vortex interactions and performs differently on each side, resulting in a dominant streamwise vortex merged behind the right thigh, which is associated with aerodynamic drag productions. In particular, leg position affects the lateral displacement between the elbow vortex and upper thigh, which is the reason for the distinct flow behaviors on each side. This study helps to better understand the flow around a track cyclist, facilitating the development of drag-saving strategies in the future.
- 1 January 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (1)
Open AccessOn the evolution of flow structures around a track cyclist
In this study, flow structures and their evolution over a track cyclist were investigated through wind tunnel tests. In supplement to the experiment, high-fidelity numerical simulations were also conducted to demonstrate the origins of global flow structures. In wind tunnel tests, a full-scale track cyclist mannequin was built based on the three-dimensional scanning of an elite track cyclist in a riding position of a sprint event, and a Cobra probe was used to measure the wake structures. The results show that the preeminent flow structures around the track cyclist mannequin are the streamwise vortices originating from different body parts. The evolution of these vortices involves strong vortex interactions and performs differently on each side, resulting in a dominant streamwise vortex merged behind the right thigh, which is associated with aerodynamic drag productions. In particular, leg position affects the lateral displacement between the elbow vortex and upper thigh, which is the reason for the distinct flow behaviors on each side. This study helps to better understand the flow around a track cyclist, facilitating the development of drag-saving strategies in the future.
- 1 April 2023
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 61 (4) , 1876-1880
Development of a Low-Noise and High-Efficiency Propeller Using Divergent Riblet Surface Pattern
- 1 April 2023
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 61 (4) , 1876-1880
Development of a Low-Noise and High-Efficiency Propeller Using Divergent Riblet Surface Pattern
- 1 March 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (3) , 035103
Experimental investigation on cylinder noise and its reductions by identifying aerodynamic sound sources in flow fields
Through anechoic wind tunnel tests, this study comprehensively investigates the noise and drag reductions on a circular cylinder with dimples. Dimples built on a surface pattern fabric cover the cylinder surface as one of the passive flow control methods. The force, noise, and flow field measurements are performed at diameter-based Reynolds numbers ranging from to , covering the sub-critical, critical, and supercritical regimes. The force and noise measurement results show that dimple fabric simultaneously reduces noise and drag in the critical regime. The changes in flow structures were characterized by the Time-resolved Particle Image Velocimetry (TR-PIV) measurements. Based on the vortex sound theory, the flow analysis shows that the dominant sound sources are found to be concentrated near the cylinder surface, which is caused by the unsteady vortex motions near the separation locations during the process of vortex shedding. The cross-correlation between the synchronized TR-PIV and microphone measurements further supports the conclusions. Moreover, the cylinder noise reductions controlled by the dimples are directly associated with the reduced sound sources in the critical and supercritical regimes, corresponding to the reduced strength of the vortex shedding.- 1 March 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (3) , 035103
Experimental investigation on cylinder noise and its reductions by identifying aerodynamic sound sources in flow fields
Through anechoic wind tunnel tests, this study comprehensively investigates the noise and drag reductions on a circular cylinder with dimples. Dimples built on a surface pattern fabric cover the cylinder surface as one of the passive flow control methods. The force, noise, and flow field measurements are performed at diameter-based Reynolds numbers ranging from to , covering the sub-critical, critical, and supercritical regimes. The force and noise measurement results show that dimple fabric simultaneously reduces noise and drag in the critical regime. The changes in flow structures were characterized by the Time-resolved Particle Image Velocimetry (TR-PIV) measurements. Based on the vortex sound theory, the flow analysis shows that the dominant sound sources are found to be concentrated near the cylinder surface, which is caused by the unsteady vortex motions near the separation locations during the process of vortex shedding. The cross-correlation between the synchronized TR-PIV and microphone measurements further supports the conclusions. Moreover, the cylinder noise reductions controlled by the dimples are directly associated with the reduced sound sources in the critical and supercritical regimes, corresponding to the reduced strength of the vortex shedding.- 1 March 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (3) , 035111
On the cylinder noise and drag reductions in different Reynolds number ranges using surface pattern fabrics
This study experimentally investigates the potential of using surface pattern fabrics for the cylinder noise and drag control in different Reynolds number ranges. The aerodynamic and aeroacoustic effects were evaluated through the noise and force measurements in an anechoic wind tunnel. It was observed that the noise and drag reductions take place simultaneously but in different Reynolds number ranges, corresponding to the cylinder flow in different flow regimes, e.g., sub-critical, critical, and supercritical flow regimes. Microphone arc array measurements reveal that the suppression of the Aeolian tone in the critical regime is the major cause of noise reductions, and the noise directivity gradually loses dipole features in the critical and supercritical flow regimes, which is probably related to the reduced lift fluctuation coefficient and the spanwise segment of the sound sources. Further hotwire wake survey revealed significant changes in flow dynamics, which explain the variations of noise and drag in different flow regimes. We have shown for the first time that fabric with different surface patterns can effectively reduce cylinder drag and noise in different Reynolds number ranges. Since the Reynolds number is a key factor that determines the flow state in practical engineering applications, e.g., cycling aerodynamics, this study suggests that optimal drag and noise reductions can be realized by employing the combinations of different surface pattern fabrics to account for the Reynolds number effects.
- 1 March 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (3) , 035111
On the cylinder noise and drag reductions in different Reynolds number ranges using surface pattern fabrics
This study experimentally investigates the potential of using surface pattern fabrics for the cylinder noise and drag control in different Reynolds number ranges. The aerodynamic and aeroacoustic effects were evaluated through the noise and force measurements in an anechoic wind tunnel. It was observed that the noise and drag reductions take place simultaneously but in different Reynolds number ranges, corresponding to the cylinder flow in different flow regimes, e.g., sub-critical, critical, and supercritical flow regimes. Microphone arc array measurements reveal that the suppression of the Aeolian tone in the critical regime is the major cause of noise reductions, and the noise directivity gradually loses dipole features in the critical and supercritical flow regimes, which is probably related to the reduced lift fluctuation coefficient and the spanwise segment of the sound sources. Further hotwire wake survey revealed significant changes in flow dynamics, which explain the variations of noise and drag in different flow regimes. We have shown for the first time that fabric with different surface patterns can effectively reduce cylinder drag and noise in different Reynolds number ranges. Since the Reynolds number is a key factor that determines the flow state in practical engineering applications, e.g., cycling aerodynamics, this study suggests that optimal drag and noise reductions can be realized by employing the combinations of different surface pattern fabrics to account for the Reynolds number effects.
- 1 November 2021
- Published by AIP Publishing in Physics of Fluids
- Vol. 33 (11) , 115110
An experimental investigation of drag and noise reduction from a circular cylinder using longitudinal grooves
Aerodynamic and aeroacoustic characteristics of a cylinder with longitudinal grooves were studied in an anechoic wind tunnel, emphasizing on drag and noise attenuation. The parallel mounted load cells and a single microphone measured the aerodynamic resistance and noise of a circular cylinder with longitudinal grooves at Reynolds number ranging from to , covering the flow regimes from the sub-critical to the post-critical states. The results show that longitudinal grooves can effectively trigger the boundary-layer transition started at a Reynolds number around , causing the so-called drag crisis. During the transition process, a drag reduction over 50% and a maximum noise attenuation over 15 dB can be achieved by longitudinal grooves. The variations of the drag and noise are linked to the near-field flow measurements using hot-wire in different regimes, enhancing our understanding of the problem.- 1 November 2021
- Published by AIP Publishing in Physics of Fluids
- Vol. 33 (11) , 115110
An experimental investigation of drag and noise reduction from a circular cylinder using longitudinal grooves
Aerodynamic and aeroacoustic characteristics of a cylinder with longitudinal grooves were studied in an anechoic wind tunnel, emphasizing on drag and noise attenuation. The parallel mounted load cells and a single microphone measured the aerodynamic resistance and noise of a circular cylinder with longitudinal grooves at Reynolds number ranging from to , covering the flow regimes from the sub-critical to the post-critical states. The results show that longitudinal grooves can effectively trigger the boundary-layer transition started at a Reynolds number around , causing the so-called drag crisis. During the transition process, a drag reduction over 50% and a maximum noise attenuation over 15 dB can be achieved by longitudinal grooves. The variations of the drag and noise are linked to the near-field flow measurements using hot-wire in different regimes, enhancing our understanding of the problem.- 1 August 2021
- Published by Institute of Noise Control Engineering (INCE) in INTER-NOISE and NOISE-CON Congress and Conference Proceedings
- Vol. 263 (2) , 4410-4417
The multi-functional rotor aerodynamic and aeroacoustic test platform at HKUST
This paper describes the multi-functional rotor noise and aerodynamics test platform at the Hong Kong University of Science and Technology (HKUST). To investigate the noise characteristics of propellers with aerodynamic flows, the test rig is installed in the 2.5×2 (m) low-speed and low-noise wind tunnel in the Aerodynamic and Acoustic Facility (AAF) at HKUST. The wind tunnel can facilitate flow from 0 to 40 m/s. The test rig is assembled in a turntable on the ceiling of the tunnel wall, which enables the testing range of pitch angle can vary from 0° (axial flow) to 90° (parallel flow), with an accuracy of 0.1°. The noise produced by the rotor is measured by a set of wall-mounted surface microphones. Semi-empirical calibration is conducted to quantify the noise reflection by the tunnel walls. A low-noise struct has been designed and manufactured to locate a set of far-field microphones equipped with nosecone, to improve the quality of acoustic measurement inside the flow. In addition, a synchronized system is developed to conduct the phase-locking Particle Image Velocimetry (PIV) measurement on the rotor, to study the flow pattern to better understand the noise generation mechanism.
- 1 August 2021
- Published by Institute of Noise Control Engineering (INCE) in INTER-NOISE and NOISE-CON Congress and Conference Proceedings
- Vol. 263 (2) , 4410-4417
The multi-functional rotor aerodynamic and aeroacoustic test platform at HKUST
This paper describes the multi-functional rotor noise and aerodynamics test platform at the Hong Kong University of Science and Technology (HKUST). To investigate the noise characteristics of propellers with aerodynamic flows, the test rig is installed in the 2.5×2 (m) low-speed and low-noise wind tunnel in the Aerodynamic and Acoustic Facility (AAF) at HKUST. The wind tunnel can facilitate flow from 0 to 40 m/s. The test rig is assembled in a turntable on the ceiling of the tunnel wall, which enables the testing range of pitch angle can vary from 0° (axial flow) to 90° (parallel flow), with an accuracy of 0.1°. The noise produced by the rotor is measured by a set of wall-mounted surface microphones. Semi-empirical calibration is conducted to quantify the noise reflection by the tunnel walls. A low-noise struct has been designed and manufactured to locate a set of far-field microphones equipped with nosecone, to improve the quality of acoustic measurement inside the flow. In addition, a synchronized system is developed to conduct the phase-locking Particle Image Velocimetry (PIV) measurement on the rotor, to study the flow pattern to better understand the noise generation mechanism.