Anatoly Konovalov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Anatoly Konovalov has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Alexander Smirnov
Institute of Cytology and Genetics of the Siberian Branch of the Russian Academy of Sciences
2 shared publications - Vladislav Kanakin
Institute of Engineering Science, UB RAS, 34 Komsomolskaya St., 620049 Ekaterinburg, Russia
2 shared publications - Evgeniya O. Smirnova
Institute of Engineering Science, Ural Branch of RAS, 620049 Ekaterinburg, Russia
1 shared publication
Latest Publications
- Open Access
- 10 January 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (2) , 939
Neural Network Modeling of Microstructure Formation in an AlMg6/10% SiC Metal Matrix Composite and Identification of Its Softening Mechanisms under High-Temperature Deformation
The paper investigates the rheological behavior and microstructuring of an AlMg6/10% SiC metal matrix composite (MMC). The rheological behavior and microstructuring of the AlMg6/10% SiC composite is studied for strain rates ranging between 0.1 and 4 s−1 and temperatures ranging from 300 to 500 °C. The microstructure formation is studied using EBSD analysis, as well as finite element simulation and neural network models. The paper proposes a new method of adding data to a training sample, which allows neural networks to correctly predict the behavior of microstructure parameters, such as the average grain diameter, and the fraction and density of low-angle boundaries with scanty initial experimental data. The use of neural networks has made it possible to relate the thermomechanical parameters of deformation to the microstructure parameters formed under these conditions. These dependences allow us to establish that, at strain rates ranging from 0.1 to 4 s−1 and temperatures between 300 to 500 °C, the main softening processes in the AlMg6/10% SiC MMC are dynamic recovery and continuous dynamic recrystallization accompanied, under certain strain and strain rate conditions at 300 and 350 °C, by geometric recrystallization.
- 10 January 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (2) , 939
Open AccessNeural Network Modeling of Microstructure Formation in an AlMg6/10% SiC Metal Matrix Composite and Identification of Its Softening Mechanisms under High-Temperature Deformation
The paper investigates the rheological behavior and microstructuring of an AlMg6/10% SiC metal matrix composite (MMC). The rheological behavior and microstructuring of the AlMg6/10% SiC composite is studied for strain rates ranging between 0.1 and 4 s−1 and temperatures ranging from 300 to 500 °C. The microstructure formation is studied using EBSD analysis, as well as finite element simulation and neural network models. The paper proposes a new method of adding data to a training sample, which allows neural networks to correctly predict the behavior of microstructure parameters, such as the average grain diameter, and the fraction and density of low-angle boundaries with scanty initial experimental data. The use of neural networks has made it possible to relate the thermomechanical parameters of deformation to the microstructure parameters formed under these conditions. These dependences allow us to establish that, at strain rates ranging from 0.1 to 4 s−1 and temperatures between 300 to 500 °C, the main softening processes in the AlMg6/10% SiC MMC are dynamic recovery and continuous dynamic recrystallization accompanied, under certain strain and strain rate conditions at 300 and 350 °C, by geometric recrystallization.
- Open Access
- 10 November 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (22) , 10590
Using the Instrumented Indentation Technique to Determine Damage in Sintered Metal Matrix Composites after High-Temperature Deformation
The paper shows the applicability of data on the evolution of the elastic modulus measured by the instrumented microindentation technique to the determination of accumulated damage in metal matrix composites (MMCs) under high temperature deformation. A composite with a V95 aluminum alloy matrix (the Russian equivalent of the 7075 alloy) and SiC reinforcing particles is used as the research material. The metal matrix composite was produced by powder technology. The obtained results show that, under macroscopic compression at temperatures ranging between 300 and 500 °C, the V95\10% SiC MMC has the best plasticity at 300 °C. At a deformation temperature of 500 °C, the plastic properties are significantly lower than those at 300 and 400 °C.
- 10 November 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (22) , 10590
Open AccessUsing the Instrumented Indentation Technique to Determine Damage in Sintered Metal Matrix Composites after High-Temperature Deformation
The paper shows the applicability of data on the evolution of the elastic modulus measured by the instrumented microindentation technique to the determination of accumulated damage in metal matrix composites (MMCs) under high temperature deformation. A composite with a V95 aluminum alloy matrix (the Russian equivalent of the 7075 alloy) and SiC reinforcing particles is used as the research material. The metal matrix composite was produced by powder technology. The obtained results show that, under macroscopic compression at temperatures ranging between 300 and 500 °C, the V95\10% SiC MMC has the best plasticity at 300 °C. At a deformation temperature of 500 °C, the plastic properties are significantly lower than those at 300 and 400 °C.