Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Vladislav Kanakin has a total of 9 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Determining the Elastic Constants and Thickness of the Interphase in Fiberglass Plastic Composites from Micromechanical and Macromechanical Tests

    by Alexander Smirnov, Evgeniya Smirnova, Dmitry Vichuzhanin, Yulia Khudorozhkova, Irina Spirina, Vladislav Kanakin, Olga Muizemnek

    The aim of this paper is to describe a methodology for determining the elastic constants and thickness of the interphase between matrix and fiber in fiberglass plastic composites from macro- and micromechanical testing. Macromechanical testing is tension of unidirectional fiberglass plastics along and across the fiber direction. Micromechanical testing is tension of glass fibers and instrumented microindentation into the matrix and the fiberglass. The interphase thickness is determined by dynamic force microscopy on thin sections without a height difference. The measured interphase thickness is 621 nm. Based on the interphase thickness, a mesomechanical finite element model of a fiberglass monolayer is constructed. As a result, it is found that the elastic modulus and Poisson’s ratio are 12.7 GPa, 0.07. It is established that the elastic properties of the interphase differ significantly from those of the matrix. The paper also explores the possibility of determining the interphase thickness through computational experiments. It turns out that by knowing the actual elastic properties of the matrix and the fiber, as well as the fiberglass monolayer, it is feasible to calculate the interphase and its elastic properties with acceptable engineering accuracy. The deviation of the calculated interphase thickness from the experimentally measured one is 6%.


  • Open Access

    Neural Network Modeling of Microstructure Formation in an AlMg6/10% SiC Metal Matrix Composite and Identification of Its Softening Mechanisms under High-Temperature Deformation

    by Alexander Smirnov, Vladislav Kanakin, Anatoly Konovalov

    The paper investigates the rheological behavior and microstructuring of an AlMg6/10% SiC metal matrix composite (MMC). The rheological behavior and microstructuring of the AlMg6/10% SiC composite is studied for strain rates ranging between 0.1 and 4 s−1 and temperatures ranging from 300 to 500 °C. The microstructure formation is studied using EBSD analysis, as well as finite element simulation and neural network models. The paper proposes a new method of adding data to a training sample, which allows neural networks to correctly predict the behavior of microstructure parameters, such as the average grain diameter, and the fraction and density of low-angle boundaries with scanty initial experimental data. The use of neural networks has made it possible to relate the thermomechanical parameters of deformation to the microstructure parameters formed under these conditions. These dependences allow us to establish that, at strain rates ranging from 0.1 to 4 s−1 and temperatures between 300 to 500 °C, the main softening processes in the AlMg6/10% SiC MMC are dynamic recovery and continuous dynamic recrystallization accompanied, under certain strain and strain rate conditions at 300 and 350 °C, by geometric recrystallization.


  • Open Access

    Using the Instrumented Indentation Technique to Determine Damage in Sintered Metal Matrix Composites after High-Temperature Deformation

    by Alexander Smirnov, Evgeniya Smirnova, Anatoly Konovalov, Vladislav Kanakin

    The paper shows the applicability of data on the evolution of the elastic modulus measured by the instrumented microindentation technique to the determination of accumulated damage in metal matrix composites (MMCs) under high temperature deformation. A composite with a V95 aluminum alloy matrix (the Russian equivalent of the 7075 alloy) and SiC reinforcing particles is used as the research material. The metal matrix composite was produced by powder technology. The obtained results show that, under macroscopic compression at temperatures ranging between 300 and 500 °C, the V95\10% SiC MMC has the best plasticity at 300 °C. At a deformation temperature of 500 °C, the plastic properties are significantly lower than those at 300 and 400 °C.


  • Neural network modeling of the rheology of the AlMg6 alloy under the dispersoid barrier effect and the inhibition of dynamic relaxation processes

    by A. S. Smirnov, A. V. Konovalov, V. S. Kanakin

    The paper deals with a neural network to model the flow stress of the AlMg6 alloy at temperatures ranging between 300 and 500 C and strain rates from 1 to 25 s−1. In this temperature–strain-rate range, the movement of free dislocations is blocked and dynamic relaxation processes are inhibited. The results of training the neural network and its verification at a temperature not used in the training show that neural networks with a single hidden layer can correctly approximate and predict the rheological behavior of the AlMg6 alloy for the studied temperature–strain-rate range of deformation.