Krešimir Jukić
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Krešimir Jukić has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Tomislav Jarak
Faculty of Mechanical Engineering and Naval Architecture, University of Zagreb, Zagreb, Croatia
2 shared publications - Zdenko Tonković
Faculty of Mechanical Engineering and Naval Architecture, University of Zagreb, Zagreb, Croatia
2 shared publications - Ivica Skozrit
Faculty of Mechanical Engineering and Naval Architecture, University of Zagreb, Ivana Lucica 5, 10000 Zagreb, Croatia
1 shared publication - Mato Perić
Department of Mechatronics, University North, Trg dr. Žarka Dolinara 1, 48000 Koprivnica, Croatia
1 shared publication - Tamara Aleksandrov Fabijanić
Faculty of Mechanical Engineering and Naval Architecture, University of Zagreb, Ivana Lucica 5, 10000 Zagreb, Croatia
1 shared publication - Zoran Tomic
Uppsala University Hospital
1 shared publication
Latest Publications
- Open Access
- 9 July 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (14) , 2356
Phase-Field Modeling of Fused Silica Cone-Crack Vickers Indentation
In this paper, a 3D phase-field model for brittle fracture is applied for analyzing the complex fracture patterns appearing during the Vickers indentation of fused silica. Although recent phase-field models for the fracture caused by the indentation loading have been verified by some simpler academic axis-symmetric examples, a proper validation of such models is still missing. In addition, heavy computational costs, and a complicated compression stress field under the indenter, which demands different energy decompositions, have been identified as the most important impediments for the successful application of the phase-field method for such problems. An adaptive strategy is utilized for reducing the computational costs, and some modifications are introduced, which enable an accurate simulation of the Vickers indentation fracture. Here, the fracture initiation ring outside the contact zone is detected by using different energy decompositions, and the dominant cone-crack formation under the Vickers indenter is observed. Different contact conditions are investigated. The proposed model is validated by experimental measurements, and a quantitative and qualitative comparison between experimental and numerical results is conducted.
- 9 July 2022
- Published by MDPI AG in Nanomaterials
- Vol. 12 (14) , 2356
Open AccessPhase-Field Modeling of Fused Silica Cone-Crack Vickers Indentation
In this paper, a 3D phase-field model for brittle fracture is applied for analyzing the complex fracture patterns appearing during the Vickers indentation of fused silica. Although recent phase-field models for the fracture caused by the indentation loading have been verified by some simpler academic axis-symmetric examples, a proper validation of such models is still missing. In addition, heavy computational costs, and a complicated compression stress field under the indenter, which demands different energy decompositions, have been identified as the most important impediments for the successful application of the phase-field method for such problems. An adaptive strategy is utilized for reducing the computational costs, and some modifications are introduced, which enable an accurate simulation of the Vickers indentation fracture. Here, the fracture initiation ring outside the contact zone is detected by using different energy decompositions, and the dominant cone-crack formation under the Vickers indenter is observed. Different contact conditions are investigated. The proposed model is validated by experimental measurements, and a quantitative and qualitative comparison between experimental and numerical results is conducted.
- Open Access
Numerical Calculation of Stress Intensity Factors for Semi-Elliptical Surface Cracks in Buried-Arc Welded Thick Plates
The present study deals with the influence of residual stresses induced by the buried-arc welding on the crack behavior in two butt-welded 20 mm thick plates. The following steps were undertaken: the thermo-mechanical simulation of the welding process, the mapping of stress results from a finite element (FE) mesh used for the welding simulation to a new FE mesh with a crack, the stress balancing, and the stress intensity factor (SIF) calculation. The FE and weight function (WF) methods were used to investigate the SIFs at the deepest point of semi-elliptical surface cracks with different geometries, orientations, and positions in relation to the weld line. In the case of cracks perpendicular to the weld line, the FE and WF results showed a good agreement for smaller cracks, while deviation between the results increases with the size of the crack. Considering the SIF solutions for the cracks of arbitrary orientation, it was observed that for some cases, the SIF value for mode III of crack opening can be of significant influence.
Open AccessNumerical Calculation of Stress Intensity Factors for Semi-Elliptical Surface Cracks in Buried-Arc Welded Thick Plates
The present study deals with the influence of residual stresses induced by the buried-arc welding on the crack behavior in two butt-welded 20 mm thick plates. The following steps were undertaken: the thermo-mechanical simulation of the welding process, the mapping of stress results from a finite element (FE) mesh used for the welding simulation to a new FE mesh with a crack, the stress balancing, and the stress intensity factor (SIF) calculation. The FE and weight function (WF) methods were used to investigate the SIFs at the deepest point of semi-elliptical surface cracks with different geometries, orientations, and positions in relation to the weld line. In the case of cracks perpendicular to the weld line, the FE and WF results showed a good agreement for smaller cracks, while deviation between the results increases with the size of the crack. Considering the SIF solutions for the cracks of arbitrary orientation, it was observed that for some cases, the SIF value for mode III of crack opening can be of significant influence.