Jinghui Zhao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jinghui Zhao has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Zixi Wang
Tsinghua University
3 shared publications - Tiancai Ma
School of Automotive Studies, Tongji University, Shanghai 201804, China
2 shared publications - Yanbo Yang
School of Automotive Studies, Tongji University, Shanghai 201804, China
2 shared publications - Yuchao Ke
Key Laboratory of High-Performance Rubber & Products of Anhui Province, Ningguo 242300, China
2 shared publications - Cuihong Jin
New Energy R&D Center, Weichai Power Co., Ltd., Weifang 261061, China
1 shared publication - Decai Li
School of Mechanical, Electronic and Control Engineering, Beijing Jiaotong University, Beijing, China
1 shared publication
Latest Publications
- Open Access
- 4 August 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (15) , 12002
Research on Design and Optimization of Large Metal Bipolar Plate Sealing for Proton Exchange Membrane Fuel Cells
The sealing system, as the most important load-bearing component, is a critical part of the stack assembly in a proton exchange membrane fuel cell (PEMFC). Currently, flat or single-peak sealing gaskets are commonly used for large metal bipolar plate sealing, which can easily cause problems such as significant internal stress and distortion displacement. In order to solve this problem, an innovative double-peak sealing gasket structure is proposed. Based on the Mooney–Rivlin constitutive model, the impact of the sealing material hardness, friction coefficient, and compression ratio on the sealing performance are investigated. Meanwhile, the double-peak seal is fabricated and assembled into a single fuel cell for testing. The results show that the sealing performance of a double-peak sealing gasket with extended wings has been optimized, and the maximum contact pressure on the upper and lower contact surfaces is 1.2 MPa and 0.67 MPa, respectively, which is greater than the given air pressure of 0.1 MPa. And the sealing effect is optimal with a 45 Shore A hardness rubber, a friction coefficient of 0.05, and an initial compression ratio of 35%. The simulation and experimental sealing performance of the sealing gasket under different compression ratios remain similar.
- 4 August 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (15) , 12002
Open AccessResearch on Design and Optimization of Large Metal Bipolar Plate Sealing for Proton Exchange Membrane Fuel Cells
The sealing system, as the most important load-bearing component, is a critical part of the stack assembly in a proton exchange membrane fuel cell (PEMFC). Currently, flat or single-peak sealing gaskets are commonly used for large metal bipolar plate sealing, which can easily cause problems such as significant internal stress and distortion displacement. In order to solve this problem, an innovative double-peak sealing gasket structure is proposed. Based on the Mooney–Rivlin constitutive model, the impact of the sealing material hardness, friction coefficient, and compression ratio on the sealing performance are investigated. Meanwhile, the double-peak seal is fabricated and assembled into a single fuel cell for testing. The results show that the sealing performance of a double-peak sealing gasket with extended wings has been optimized, and the maximum contact pressure on the upper and lower contact surfaces is 1.2 MPa and 0.67 MPa, respectively, which is greater than the given air pressure of 0.1 MPa. And the sealing effect is optimal with a 45 Shore A hardness rubber, a friction coefficient of 0.05, and an initial compression ratio of 35%. The simulation and experimental sealing performance of the sealing gasket under different compression ratios remain similar.
- Open Access
Effect of Clamping Compression on the Mechanical Performance of a Carbon Paper Gas Diffusion Layer in Polymer Electrolyte Membrane Fuel Cells
During all the assembly stages of a polymer electrolyte membrane fuel cell (PEMFC) stack, gas diffusion layers (GDLs) endure clamping loads in the through-plane direction several times. Under such complicated assembly conditions, GDLs have to deform with the changes in structure, surface roughness, pore size, etc. A comprehensive understanding of the compressive performance of GDLs at different clamping phases is crucial to the assembly process improvement of PEMFCs. Two typical clamping compression was designed and performed to get close to the actual assembly conditions of PEMFCs. The results indicate that the initial clamping compression and the magnitude of the maximum clamping load have great impacts on the segmented compressive properties of GDLs. The nonlinear compressive performance of the GDL is mainly attributed to the unique microstructural information. The rough surface morphology contributes to the initial compressive characteristics where the big strain along with the small stress occurs, and the irreversible failures such as carbon fiber breakages and adhesive failures between fibers and binders account for the hysteresis between different compression stages. Importantly, it is found that the clamping compression hardly influences the small pore distribution below 175 μm but affects the large pore distribution over 200 μm.
Open AccessEffect of Clamping Compression on the Mechanical Performance of a Carbon Paper Gas Diffusion Layer in Polymer Electrolyte Membrane Fuel Cells
During all the assembly stages of a polymer electrolyte membrane fuel cell (PEMFC) stack, gas diffusion layers (GDLs) endure clamping loads in the through-plane direction several times. Under such complicated assembly conditions, GDLs have to deform with the changes in structure, surface roughness, pore size, etc. A comprehensive understanding of the compressive performance of GDLs at different clamping phases is crucial to the assembly process improvement of PEMFCs. Two typical clamping compression was designed and performed to get close to the actual assembly conditions of PEMFCs. The results indicate that the initial clamping compression and the magnitude of the maximum clamping load have great impacts on the segmented compressive properties of GDLs. The nonlinear compressive performance of the GDL is mainly attributed to the unique microstructural information. The rough surface morphology contributes to the initial compressive characteristics where the big strain along with the small stress occurs, and the irreversible failures such as carbon fiber breakages and adhesive failures between fibers and binders account for the hysteresis between different compression stages. Importantly, it is found that the clamping compression hardly influences the small pore distribution below 175 μm but affects the large pore distribution over 200 μm.
- Open Access
- 11 November 2021
- Published by MDPI AG in World Electric Vehicle Journal
- Vol. 12 (4) , 237
Study on a New Static Sealing Method and Sealing Performance Evaluation Model for PEMFC
The long-term stability and durability of seals are critical for various instruments and types of equipment. For static sealing, an important sealing state, there are currently two representative sealing methods, namely, pre-compressing static sealing and adhesive static sealing. In this paper, the characteristics and shortcomings of these sealing methods are summarized. At present, some static sealing requirements are urgent and difficult. For example, the deterioration of the sealing performance is an important factor which limits the service life of proton exchange membrane fuel cells and redox flow batteries. Therefore, a new method of static sealing whose sealing materials are rubber elastomers is proposed, named alterable static sealing. Then, its sealing processes are proposed. Furthermore, the actual contact area ratio r is used as the standard for sealability. Based on the mathematical model of pre-compressing static sealing, the influence of interface bonding was considered, and the mathematical model of alterable static sealing was established. Moreover, the compensatory effect of alterable static sealing on the static sealing capacity of rubber elastomers was proved.
- 11 November 2021
- Published by MDPI AG in World Electric Vehicle Journal
- Vol. 12 (4) , 237
Open AccessStudy on a New Static Sealing Method and Sealing Performance Evaluation Model for PEMFC
The long-term stability and durability of seals are critical for various instruments and types of equipment. For static sealing, an important sealing state, there are currently two representative sealing methods, namely, pre-compressing static sealing and adhesive static sealing. In this paper, the characteristics and shortcomings of these sealing methods are summarized. At present, some static sealing requirements are urgent and difficult. For example, the deterioration of the sealing performance is an important factor which limits the service life of proton exchange membrane fuel cells and redox flow batteries. Therefore, a new method of static sealing whose sealing materials are rubber elastomers is proposed, named alterable static sealing. Then, its sealing processes are proposed. Furthermore, the actual contact area ratio r is used as the standard for sealability. Based on the mathematical model of pre-compressing static sealing, the influence of interface bonding was considered, and the mathematical model of alterable static sealing was established. Moreover, the compensatory effect of alterable static sealing on the static sealing capacity of rubber elastomers was proved.