Yuchao Ke
Yuchao Ke has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Jinghui Zhao
School of Automotive Engineering, Tongji University, Shanghai 201804, China
2 shared publications - Yanqin Chen
Department of Mechanical Engineering, Tsinghua University, Beijing 100084, China
2 shared publications - Zixi Wang
Tsinghua University
2 shared publications - Chongdu Cho
Mechanical Engineering, Inha University, Incheon, Korea
1 shared publication - Cuihong Jin
New Energy R&D Center, Weichai Power Co., Ltd., Weifang 261061, China
1 shared publication - Decai Li
School of Mechanical, Electronic and Control Engineering, Beijing Jiaotong University, Beijing, China
1 shared publication
Latest Publications
- Open Access
Effect of Clamping Compression on the Mechanical Performance of a Carbon Paper Gas Diffusion Layer in Polymer Electrolyte Membrane Fuel Cells
During all the assembly stages of a polymer electrolyte membrane fuel cell (PEMFC) stack, gas diffusion layers (GDLs) endure clamping loads in the through-plane direction several times. Under such complicated assembly conditions, GDLs have to deform with the changes in structure, surface roughness, pore size, etc. A comprehensive understanding of the compressive performance of GDLs at different clamping phases is crucial to the assembly process improvement of PEMFCs. Two typical clamping compression was designed and performed to get close to the actual assembly conditions of PEMFCs. The results indicate that the initial clamping compression and the magnitude of the maximum clamping load have great impacts on the segmented compressive properties of GDLs. The nonlinear compressive performance of the GDL is mainly attributed to the unique microstructural information. The rough surface morphology contributes to the initial compressive characteristics where the big strain along with the small stress occurs, and the irreversible failures such as carbon fiber breakages and adhesive failures between fibers and binders account for the hysteresis between different compression stages. Importantly, it is found that the clamping compression hardly influences the small pore distribution below 175 μm but affects the large pore distribution over 200 μm.
Open AccessEffect of Clamping Compression on the Mechanical Performance of a Carbon Paper Gas Diffusion Layer in Polymer Electrolyte Membrane Fuel Cells
During all the assembly stages of a polymer electrolyte membrane fuel cell (PEMFC) stack, gas diffusion layers (GDLs) endure clamping loads in the through-plane direction several times. Under such complicated assembly conditions, GDLs have to deform with the changes in structure, surface roughness, pore size, etc. A comprehensive understanding of the compressive performance of GDLs at different clamping phases is crucial to the assembly process improvement of PEMFCs. Two typical clamping compression was designed and performed to get close to the actual assembly conditions of PEMFCs. The results indicate that the initial clamping compression and the magnitude of the maximum clamping load have great impacts on the segmented compressive properties of GDLs. The nonlinear compressive performance of the GDL is mainly attributed to the unique microstructural information. The rough surface morphology contributes to the initial compressive characteristics where the big strain along with the small stress occurs, and the irreversible failures such as carbon fiber breakages and adhesive failures between fibers and binders account for the hysteresis between different compression stages. Importantly, it is found that the clamping compression hardly influences the small pore distribution below 175 μm but affects the large pore distribution over 200 μm.
- Open Access
- 11 November 2021
- Published by MDPI AG in World Electric Vehicle Journal
- Vol. 12 (4) , 237
Study on a New Static Sealing Method and Sealing Performance Evaluation Model for PEMFC
The long-term stability and durability of seals are critical for various instruments and types of equipment. For static sealing, an important sealing state, there are currently two representative sealing methods, namely, pre-compressing static sealing and adhesive static sealing. In this paper, the characteristics and shortcomings of these sealing methods are summarized. At present, some static sealing requirements are urgent and difficult. For example, the deterioration of the sealing performance is an important factor which limits the service life of proton exchange membrane fuel cells and redox flow batteries. Therefore, a new method of static sealing whose sealing materials are rubber elastomers is proposed, named alterable static sealing. Then, its sealing processes are proposed. Furthermore, the actual contact area ratio r is used as the standard for sealability. Based on the mathematical model of pre-compressing static sealing, the influence of interface bonding was considered, and the mathematical model of alterable static sealing was established. Moreover, the compensatory effect of alterable static sealing on the static sealing capacity of rubber elastomers was proved.
- 11 November 2021
- Published by MDPI AG in World Electric Vehicle Journal
- Vol. 12 (4) , 237
Open AccessStudy on a New Static Sealing Method and Sealing Performance Evaluation Model for PEMFC
The long-term stability and durability of seals are critical for various instruments and types of equipment. For static sealing, an important sealing state, there are currently two representative sealing methods, namely, pre-compressing static sealing and adhesive static sealing. In this paper, the characteristics and shortcomings of these sealing methods are summarized. At present, some static sealing requirements are urgent and difficult. For example, the deterioration of the sealing performance is an important factor which limits the service life of proton exchange membrane fuel cells and redox flow batteries. Therefore, a new method of static sealing whose sealing materials are rubber elastomers is proposed, named alterable static sealing. Then, its sealing processes are proposed. Furthermore, the actual contact area ratio r is used as the standard for sealability. Based on the mathematical model of pre-compressing static sealing, the influence of interface bonding was considered, and the mathematical model of alterable static sealing was established. Moreover, the compensatory effect of alterable static sealing on the static sealing capacity of rubber elastomers was proved.
- Open Access
Investigation on Mechanical Properties of a Carbon Paper Gas Diffusion Layer through a 3-D Nonlinear and Orthotropic Constitutive Model
The mechanical loads that gas diffusion layers (GDLs) withstand in polymer electrolyte membrane fuel cell (PEMFC) stacks are sensitive to the assembly and working conditions. The mechanical properties of GDLs mostly depend on their composition materials, microstructural characteristics, operation conditions, etc. An accurate and comprehensive understanding of the mechanical performance of GDLs is significant for predicting the stress distribution and improving the assembly technology of PEMFC stacks. This study presented a novel 3-D nonlinear and orthotropic constitutive model of a carbon paper GDL to represent the material stiffness matrix with its compressive, tensile, and shear properties. Numerical simulations were performed based on the 3-D constitutive model, and the proposed 3-D model was validated against the experimental data reported previously. It is found that the simulation results of the 3-D constitutive model show a good agreement with the experimental results. Besides, the novel 3-D nonlinear and orthotropic model was applied in the overall stress simulation of a simplified PEMFC unit cell, compared to a conventional 3-D linear and isotropic model, and the simulation results of the two models show a significant difference.
Open AccessInvestigation on Mechanical Properties of a Carbon Paper Gas Diffusion Layer through a 3-D Nonlinear and Orthotropic Constitutive Model
The mechanical loads that gas diffusion layers (GDLs) withstand in polymer electrolyte membrane fuel cell (PEMFC) stacks are sensitive to the assembly and working conditions. The mechanical properties of GDLs mostly depend on their composition materials, microstructural characteristics, operation conditions, etc. An accurate and comprehensive understanding of the mechanical performance of GDLs is significant for predicting the stress distribution and improving the assembly technology of PEMFC stacks. This study presented a novel 3-D nonlinear and orthotropic constitutive model of a carbon paper GDL to represent the material stiffness matrix with its compressive, tensile, and shear properties. Numerical simulations were performed based on the 3-D constitutive model, and the proposed 3-D model was validated against the experimental data reported previously. It is found that the simulation results of the 3-D constitutive model show a good agreement with the experimental results. Besides, the novel 3-D nonlinear and orthotropic model was applied in the overall stress simulation of a simplified PEMFC unit cell, compared to a conventional 3-D linear and isotropic model, and the simulation results of the two models show a significant difference.