Luke C. Olson
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Luke C. Olson has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Brenda L. Garcia-Diaz
Savannah River National Laboratory
4 shared publications - Christopher S. Dandeneau
Savannah River National Laboratory
3 shared publications - Thomas T. Volta
Savannah River National Laboratory
3 shared publications Amanda Bye
Xcimer Energy Corporation
2 shared publicationsSilvia De Dea
Xcimer Energy Corporation
2 shared publicationsSusana Reyes
Xcimer Energy Corporation
2 shared publications
Latest Publications
- 18 November 2026
- Published by Taylor & Francis in Fusion Science and Technology
- p. 1-15
Solid-State Electrolyte Development for Hydrogen Removal from Molten Lithium by Direct LiT Electrolysis
- 18 November 2026
- Published by Taylor & Francis in Fusion Science and Technology
- p. 1-15
Solid-State Electrolyte Development for Hydrogen Removal from Molten Lithium by Direct LiT Electrolysis
- 8 July 2026
- Published by Taylor & Francis in Fusion Science and Technology
- p. 1-12
Enhancing Tritium Extraction from Molten Salts Using Metal Permeators
- 8 July 2026
- Published by Taylor & Francis in Fusion Science and Technology
- p. 1-12
Enhancing Tritium Extraction from Molten Salts Using Metal Permeators
- Open Access
- 18 February 2026
- Published by Elsevier in SSRN Electronic Journal
Sacrificial Zirconium Coatings for Corrosion Mitigation in Molten Chloride Salts
Zirconium films on Haynes 230 (H230) were examined as a corrosion mitigation strategy for potential upset conditions (e.g., loss of atmospheric control) in a molten chloride salt storage tank. In addition to Ni-based alloys such as H230, the devised method should also be applicable to Fe-based alloys. Commercial KCl-MgCl2-NaCl (45.8-47.8-6.4 mol%) salt was first purified by a two-stage thermal/chemical treatment to eliminate corrosive impurities. H230 specimens were then coated in Zr (thickness ~113 µm) using the purified salt as a transfer medium; evidence of Ni-Zr interdiffusion was observed in the as-deposited films. Zr-coated H230 (Zr-H230) coupons were ultimately immersed in the molten salt separately under air or Ar ambient at 800 °C for 100 h to assess the ability of the Zr films to protect the underlying H230. The Zr layer thickness decreased after immersion testing in both environments, but the air-exposed Zr coating was far more heavily attacked and mostly converted to ZrO2. Importantly though, the underlying H230 in the air‑exposed sample remained intact, and the Zr coating in the Ar-exposed specimen mostly stayed in the surface region where it was initially deposited. Such findings demonstrate that Zr can be applied to an alloy surface and remain in place to provide a protective function in the event of atmospheric upsets.
- 18 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessSacrificial Zirconium Coatings for Corrosion Mitigation in Molten Chloride Salts
Zirconium films on Haynes 230 (H230) were examined as a corrosion mitigation strategy for potential upset conditions (e.g., loss of atmospheric control) in a molten chloride salt storage tank. In addition to Ni-based alloys such as H230, the devised method should also be applicable to Fe-based alloys. Commercial KCl-MgCl2-NaCl (45.8-47.8-6.4 mol%) salt was first purified by a two-stage thermal/chemical treatment to eliminate corrosive impurities. H230 specimens were then coated in Zr (thickness ~113 µm) using the purified salt as a transfer medium; evidence of Ni-Zr interdiffusion was observed in the as-deposited films. Zr-coated H230 (Zr-H230) coupons were ultimately immersed in the molten salt separately under air or Ar ambient at 800 °C for 100 h to assess the ability of the Zr films to protect the underlying H230. The Zr layer thickness decreased after immersion testing in both environments, but the air-exposed Zr coating was far more heavily attacked and mostly converted to ZrO2. Importantly though, the underlying H230 in the air‑exposed sample remained intact, and the Zr coating in the Ar-exposed specimen mostly stayed in the surface region where it was initially deposited. Such findings demonstrate that Zr can be applied to an alloy surface and remain in place to provide a protective function in the event of atmospheric upsets.
- Open Access
- 5 November 2025
- Published by Office of Scientific and Technical Information (OSTI)
Tritium Extraction From a FLiBe IFE Blanket Using the CoRExt Process: Xcimer-SRNL INFUSE preliminary results
- 5 November 2025
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessTritium Extraction From a FLiBe IFE Blanket Using the CoRExt Process: Xcimer-SRNL INFUSE preliminary results
- Open Access
- 21 February 2023
- Published by Elsevier in Materials & Design
- Vol. 227, 111784
In situ high-temperature 3D imaging of the damage evolution in a SiC nuclear fuel cladding material
- 21 February 2023
- Published by Elsevier in Materials & Design
- Vol. 227, 111784
Open AccessIn situ high-temperature 3D imaging of the damage evolution in a SiC nuclear fuel cladding material
- 11 November 2021
- Published by Taylor & Francis in Nuclear Technology
- Vol. 208 (6) , 1049-1058
Alloying of U-Al-SS as a Simulant for Pu-Al-SS Alloying
The Savannah River National Laboratory evaluated several options for disposition of stainless steel (SS)–clad plutonium metal, particularly Pu-10.6 at. % Al (Pu- 1.3 wt% Al) alloy fuel. One technology considered was alloying fuel with SS. The goal of the alloying would be to make a SS-Pu alloy that was a nonproliferable waste form with secondary Pu-rich microencapsulated regions distributed throughout the refractory SS. The microencapsulation of the Pu regions should therefore allow the waste form to meet the requirements for a low attractiveness waste as defined by the U.S. Department of Energy. Plutonium-bearing alloys at these levels could potentially be suitable for disposal at a waste isolation pilot plant. Four metal ingots were successfully fabricated using U and Al as a surrogate for Pu-Al. The U was distributed and microencapsulated by the alloy matrix, thereby setting the stage for subsequent tests using SS-clad fuel elements containing Pu-10.6Al.
- 11 November 2021
- Published by Taylor & Francis in Nuclear Technology
- Vol. 208 (6) , 1049-1058
Alloying of U-Al-SS as a Simulant for Pu-Al-SS Alloying
The Savannah River National Laboratory evaluated several options for disposition of stainless steel (SS)–clad plutonium metal, particularly Pu-10.6 at. % Al (Pu- 1.3 wt% Al) alloy fuel. One technology considered was alloying fuel with SS. The goal of the alloying would be to make a SS-Pu alloy that was a nonproliferable waste form with secondary Pu-rich microencapsulated regions distributed throughout the refractory SS. The microencapsulation of the Pu regions should therefore allow the waste form to meet the requirements for a low attractiveness waste as defined by the U.S. Department of Energy. Plutonium-bearing alloys at these levels could potentially be suitable for disposal at a waste isolation pilot plant. Four metal ingots were successfully fabricated using U and Al as a surrogate for Pu-Al. The U was distributed and microencapsulated by the alloy matrix, thereby setting the stage for subsequent tests using SS-clad fuel elements containing Pu-10.6Al.