Anastasia M. Leonova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Anastasia M. Leonova has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Andrey V. Suzdaltsev
Ural Federal University, Yekaterinburg, Russia
10 shared publications - Natalia M. Leonova
Ural Federal University
10 shared publications - Aleksej A. Trofimov
Scientific Laboratory of the Electrochemical Devices and Materials, Ural Federal University, Mira St. 28, 620002 Yekaterinburg, Russia
3 shared publications A. A. Trofimov
Ural Federal University, Ekaterinburg, Russia
2 shared publications- Alexey S. Lebedev
South Urals Research Center of Mineralogy and Geoecology UB RAS, Ilmen Reservation, 456317 Miass, Russia
2 shared publications - Lyudmila Minchenko
Institute of High Temperature Electrochemistry UB RAS, Academicheskaya St. 20, 620066 Ekaterinburg, Russia
2 shared publications
Latest Publications
- Open Access
- 23 September 2025
- Published by Saratov State University in Electrochemical Energetics
- Vol. 25 (3)
Lithiation of electrodeposited silicon films
Lithium-ion batteries with improved performance are increasingly in demand in various fields. Silicon-based materials are one of the most actively studied materials, because they allow increasing the discharge capacity of the anode. In this work, we continue studying the behavior of the thin-film silicon anodes inside the anode half-cell of a lithium-ion battery in the conditions of limited charge capacity to 1000 and 4000 mA·h/g. Samples of silicon films, electrodeposited from the molten KI-KF-KCl-K2SiF6 electrolyte with the temperature of 700°C on glassy carbon in the potentiostatic mode, were used as the objects of the research. It was noted that limiting the charge capacity makes it possible to increase the number of cycles maintaining a relatively high discharge capacity and to increase the operational life of the electrodeposited silicon films. Applying the C/10 cycling current and limiting the charge capacity to 4000 mA·h/g, the discharge capacity of the samples was 3850–3930 mA·h/g, and using the 2C cycling current it was up to 3000 mA·h/g.
- 23 September 2025
- Published by Saratov State University in Electrochemical Energetics
- Vol. 25 (3)
Open AccessLithiation of electrodeposited silicon films
Lithium-ion batteries with improved performance are increasingly in demand in various fields. Silicon-based materials are one of the most actively studied materials, because they allow increasing the discharge capacity of the anode. In this work, we continue studying the behavior of the thin-film silicon anodes inside the anode half-cell of a lithium-ion battery in the conditions of limited charge capacity to 1000 and 4000 mA·h/g. Samples of silicon films, electrodeposited from the molten KI-KF-KCl-K2SiF6 electrolyte with the temperature of 700°C on glassy carbon in the potentiostatic mode, were used as the objects of the research. It was noted that limiting the charge capacity makes it possible to increase the number of cycles maintaining a relatively high discharge capacity and to increase the operational life of the electrodeposited silicon films. Applying the C/10 cycling current and limiting the charge capacity to 4000 mA·h/g, the discharge capacity of the samples was 3850–3930 mA·h/g, and using the 2C cycling current it was up to 3000 mA·h/g.
- 7 January 2025
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 50 (13) , 9877-9890
Electrochemical Performance of NiO/C Anode in Li-Ion Power Sources
- 7 January 2025
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 50 (13) , 9877-9890
Electrochemical Performance of NiO/C Anode in Li-Ion Power Sources
- Open Access
- 23 September 2024
- Published by Saratov State University in Electrochemical Energetics
- Vol. 24 (3)
Behavior of electrodeposited silicon film on glassy carbon during lithiation and delithiation
Silicon is one of the promising anode materials for lithium-ion batteries with enhanced performance. However, the degradation of silicon during lithiation/delithiation is still the main problem that prevents it commercial use as electrodes. In this work the behavior of a silicon film of about 5–6 µm thick electrodeposited from LiCl-KCl-CsCl-K2SiF6 melt on glassy carbon was studied during its lithiation and delithiation, the film being a part of the anode half-cell of a lithium-ion battery. For this purpose, the methods of cycling in galvanostatic mode, electrochemical impedance, and scanning electron microscopy were used. The principal possibility of lithiation/delithiation of the film was shown and its energy characteristics during multiple cycling were determined. However, during 714 charge-discharge cycles with the current being 0.84 A/g the discharge capacity decreased from 723 to 58 mA·h/g. It was noted that the cause of degradation of the investigated sample was the detachment of the film from the glassy carbon substrate and its cracking.
- 23 September 2024
- Published by Saratov State University in Electrochemical Energetics
- Vol. 24 (3)
Open AccessBehavior of electrodeposited silicon film on glassy carbon during lithiation and delithiation
Silicon is one of the promising anode materials for lithium-ion batteries with enhanced performance. However, the degradation of silicon during lithiation/delithiation is still the main problem that prevents it commercial use as electrodes. In this work the behavior of a silicon film of about 5–6 µm thick electrodeposited from LiCl-KCl-CsCl-K2SiF6 melt on glassy carbon was studied during its lithiation and delithiation, the film being a part of the anode half-cell of a lithium-ion battery. For this purpose, the methods of cycling in galvanostatic mode, electrochemical impedance, and scanning electron microscopy were used. The principal possibility of lithiation/delithiation of the film was shown and its energy characteristics during multiple cycling were determined. However, during 714 charge-discharge cycles with the current being 0.84 A/g the discharge capacity decreased from 723 to 58 mA·h/g. It was noted that the cause of degradation of the investigated sample was the detachment of the film from the glassy carbon substrate and its cracking.
- Open Access
- 7 March 2024
- Published by MDPI AG in Electrochem
- Vol. 5 (1) , 124-132
Electrodeposition of Silicon Fibers from KI–KF–KCl–K2SiF6 Melt and Their Electrochemical Performance during Lithiation/Delithiation
The possibility of using Si-based anodes in lithium-ion batteries is actively investigated due to the increased lithium capacity of silicon. The paper reports the preparation of submicron silicon fibers on glassy carbon in the KI–KF–KCl–K2SiF6 melt at 720 °C. For this purpose, the parameters of silicon electrodeposition in the form of fibers were determined using cyclic voltammetry, and experimental samples of ordered silicon fibers with an average diameter from 0.1 to 0.3 μm were obtained under galvanostatic electrolysis conditions. Using the obtained silicon fibers, anode half-cells of a lithium-ion battery were fabricated, and its electrochemical performance under multiple lithiations and delithiations was studied. By means of voltametric studies, it is observed that charging and discharging the anode based on the obtained silicon fibers occurs at potentials from 0.2 to 0.05 V and from 0.2 to 0.5 V, respectively. A change in discharge capacity from 520 to 200 mAh g−1 during the first 50 charge/discharge cycles at a charge current of 0.1 C and a Coulombic efficiency of 98–100% was shown. The possibility of charging silicon-based anode samples at charging currents up to 2 C was also noted; the discharge capacity ranged from 25 to 250 mAh g−1.
- 7 March 2024
- Published by MDPI AG in Electrochem
- Vol. 5 (1) , 124-132
Open AccessElectrodeposition of Silicon Fibers from KI–KF–KCl–K2SiF6 Melt and Their Electrochemical Performance during Lithiation/Delithiation
The possibility of using Si-based anodes in lithium-ion batteries is actively investigated due to the increased lithium capacity of silicon. The paper reports the preparation of submicron silicon fibers on glassy carbon in the KI–KF–KCl–K2SiF6 melt at 720 °C. For this purpose, the parameters of silicon electrodeposition in the form of fibers were determined using cyclic voltammetry, and experimental samples of ordered silicon fibers with an average diameter from 0.1 to 0.3 μm were obtained under galvanostatic electrolysis conditions. Using the obtained silicon fibers, anode half-cells of a lithium-ion battery were fabricated, and its electrochemical performance under multiple lithiations and delithiations was studied. By means of voltametric studies, it is observed that charging and discharging the anode based on the obtained silicon fibers occurs at potentials from 0.2 to 0.05 V and from 0.2 to 0.5 V, respectively. A change in discharge capacity from 520 to 200 mAh g−1 during the first 50 charge/discharge cycles at a charge current of 0.1 C and a Coulombic efficiency of 98–100% was shown. The possibility of charging silicon-based anode samples at charging currents up to 2 C was also noted; the discharge capacity ranged from 25 to 250 mAh g−1.
- Open Access
- 26 January 2024
- Published by MDPI AG in Preprints.org
Electrodeposition of Silicon Fibers from KI–KF–KCl–K2SiF6 Melt and their Electrochemical Performance During Lithiation/Delithiation
The possibility of using Si-based anodes in lithium-ion batteries is actively investigated due to the increased lithium capacity of silicon. The paper reports the preparation of submicron silicon fibers on glassy carbon in the KI–KF–KCl–K2SiF6 melt at 720°C. For this purpose, the parameters of silicon electrodeposition in the form of fibers were determined by cyclic voltammetry, and ex-perimental samples of ordered silicon fibers with an average diameter from 0.1 to 0.3 μm were obtained under galvanostatic electrolysis conditions. Using the obtained silicon fibers, anode half-cells of lithium-ion battery was fabricated, and its electrochemical performance under mul-tiple lithiation and delithiation was studied. By means of voltametric studies, it is observed that charging and discharging of the anode based on the obtained silicon fibers occurs at potentials from 0.2 to 0.05 V and from 0.2 to 0.5 V, respectively. A change in discharge capacity from 520 to 200 mAh g-1 during the first 50 charge/discharge cycles at a charge current of 0.1C and a Coulomb ef-ficiency of 98-100% was shown. The possibility of charging silicon-based anode samples at charging currents up to 2C was also noted; the discharge capacity ranged from 25 to 250 mAh g-1.
- 26 January 2024
- Published by MDPI AG in Preprints.org
Open AccessElectrodeposition of Silicon Fibers from KI–KF–KCl–K2SiF6 Melt and their Electrochemical Performance During Lithiation/Delithiation
The possibility of using Si-based anodes in lithium-ion batteries is actively investigated due to the increased lithium capacity of silicon. The paper reports the preparation of submicron silicon fibers on glassy carbon in the KI–KF–KCl–K2SiF6 melt at 720°C. For this purpose, the parameters of silicon electrodeposition in the form of fibers were determined by cyclic voltammetry, and ex-perimental samples of ordered silicon fibers with an average diameter from 0.1 to 0.3 μm were obtained under galvanostatic electrolysis conditions. Using the obtained silicon fibers, anode half-cells of lithium-ion battery was fabricated, and its electrochemical performance under mul-tiple lithiation and delithiation was studied. By means of voltametric studies, it is observed that charging and discharging of the anode based on the obtained silicon fibers occurs at potentials from 0.2 to 0.05 V and from 0.2 to 0.5 V, respectively. A change in discharge capacity from 520 to 200 mAh g-1 during the first 50 charge/discharge cycles at a charge current of 0.1C and a Coulomb ef-ficiency of 98-100% was shown. The possibility of charging silicon-based anode samples at charging currents up to 2C was also noted; the discharge capacity ranged from 25 to 250 mAh g-1.
- Open Access
- 18 December 2023
- Published by Saratov State University in Electrochemical Energetics
- Vol. 23 (4)
NiO/C-based anodes for lithium-ion current sources
- 18 December 2023
- Published by Saratov State University in Electrochemical Energetics
- Vol. 23 (4)
Open AccessNiO/C-based anodes for lithium-ion current sources
- Open Access
- 21 March 2023
- Published by Saratov State University in Electrochemical Energetics
- Vol. 23 (1)
C/SiC-based anodes for lithium-ion current sources
Compositions of ultrafine Si and C particles are promising anode materials for lithium-ion power sources with improved energy characteristics. In the work, samples of lithium-ion power sources with an anode made of ultrafine SiC fibers, as well as mixtures of SiC fibers with graphite (C/SiC) and electrolytically deposited submicron silicon fibers (C/Si/SiC) were fabricated and studied for energy characteristics. The working ability of the mixtures obtained during lithiation/delithiation was shown, and the main energy characteristics of the investigated anode half-cells were determined. After 100 cycles, the SiC anode reached a discharge capacity of 180 and 138 mA·h/g at a charge current of C/20 and C, respectively. Anodes made of mixtures (wt%) 29.5C-70.5SiC and 50Si-14.5C-35.5SiC show discharge capacities of 328 and 400 mA·h/g at a charge current of C/2. The Coulomb efficiency of all samples was above 99%.
- 21 March 2023
- Published by Saratov State University in Electrochemical Energetics
- Vol. 23 (1)
Open AccessC/SiC-based anodes for lithium-ion current sources
Compositions of ultrafine Si and C particles are promising anode materials for lithium-ion power sources with improved energy characteristics. In the work, samples of lithium-ion power sources with an anode made of ultrafine SiC fibers, as well as mixtures of SiC fibers with graphite (C/SiC) and electrolytically deposited submicron silicon fibers (C/Si/SiC) were fabricated and studied for energy characteristics. The working ability of the mixtures obtained during lithiation/delithiation was shown, and the main energy characteristics of the investigated anode half-cells were determined. After 100 cycles, the SiC anode reached a discharge capacity of 180 and 138 mA·h/g at a charge current of C/20 and C, respectively. Anodes made of mixtures (wt%) 29.5C-70.5SiC and 50Si-14.5C-35.5SiC show discharge capacities of 328 and 400 mA·h/g at a charge current of C/2. The Coulomb efficiency of all samples was above 99%.
- Open Access
- 9 January 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (2) , 901
Synthesis of C/SiC Mixtures for Composite Anodes of Lithium-Ion Power Sources
Nowadays, research aimed at the development of materials with increased energy density for lithium-ion batteries are carried out all over the world. Composite anode materials based on Si and C ultrafine particles are considered promising due to their high capacity. In this work, a new approach for carbothermal synthesis of C/SiC composite mixtures with SiC particles of fibrous morphology with a fiber diameter of 0.1–2.0 μm is proposed. The synthesis was carried out on natural raw materials (quartz and graphite) without the use of complex equipment and an argon atmosphere. Using the proposed method, C/SiC mixture as well as pure SiC were synthesized and used to manufacture anode half-cells of lithium-ion batteries. The potential use of the resulting mixtures as anode material for lithium-ion battery was shown. Energy characteristics of the mixtures were determined. After 100 cycles, pure SiC reached a discharge capacity of 180 and 138 mAh g−1 at a current of C/20 and C, respectively, and for the mixtures of (wt%) 29.5C–70.5 SiC and 50Si–14.5C–35.5SiC discharge capacity of 328 and 400 mAh g−1 at a current of C/2 were achieved. The Coulombic efficiency of the samples during cycling was over 99%.
- 9 January 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (2) , 901
Open AccessSynthesis of C/SiC Mixtures for Composite Anodes of Lithium-Ion Power Sources
Nowadays, research aimed at the development of materials with increased energy density for lithium-ion batteries are carried out all over the world. Composite anode materials based on Si and C ultrafine particles are considered promising due to their high capacity. In this work, a new approach for carbothermal synthesis of C/SiC composite mixtures with SiC particles of fibrous morphology with a fiber diameter of 0.1–2.0 μm is proposed. The synthesis was carried out on natural raw materials (quartz and graphite) without the use of complex equipment and an argon atmosphere. Using the proposed method, C/SiC mixture as well as pure SiC were synthesized and used to manufacture anode half-cells of lithium-ion batteries. The potential use of the resulting mixtures as anode material for lithium-ion battery was shown. Energy characteristics of the mixtures were determined. After 100 cycles, pure SiC reached a discharge capacity of 180 and 138 mAh g−1 at a current of C/20 and C, respectively, and for the mixtures of (wt%) 29.5C–70.5 SiC and 50Si–14.5C–35.5SiC discharge capacity of 328 and 400 mAh g−1 at a current of C/2 were achieved. The Coulombic efficiency of the samples during cycling was over 99%.
- Open Access
- 6 December 2022
- Published by Ural Federal University in Chimica Techno Acta
- Vol. 9 (4) , 20229424
Electroreduction of silicon from the NaI–KI–K2SiF6 melt for lithium-ion power sources
Silicon and silicon-based materials are increasingly used in microelectronics, metallurgy and power generation. To date the active study aimed at the development of silicon materials to be used in devices for solar energy conversion, accumulation and storage is underway. In addition, silicon is a promising anode material for lithium-ion fuel cells. In the present paper a possibility of silicon electroreduction from the NaI–KI–K2SiF6 melt in the argon atmosphere is studied. With this aim in view the electrolysis of the NaI–KI–K2SiF6 melt with glassy carbon cathode was performed under galvanostatic and potentiostatic regimes at the temperatures ranging from 650 to 750 °С. The morphology, phase and elemental analyses of the obtained silicon deposits were performed after their separation from the electrolytes by the ICP, SEM-EDX, XRD and Raman spectroscopy methods. Fiber and thread-like silicon samples of 60 to 320 nm in dimeter with admixtures concentrations (mainly oxygen) from 1.2 to 4.6 wt.% were experimentally synthesized. The obtained samples were tested as possible Si/C composite anodes for lithium-ion power sources. The discharge capacity of such power sources after 30 cycles of lithiation-delithiation ranged from 440 to 565 mAh·g–1 and the coloumbic efficiency ranged from 89 to 91%.
- 6 December 2022
- Published by Ural Federal University in Chimica Techno Acta
- Vol. 9 (4) , 20229424
Open AccessElectroreduction of silicon from the NaI–KI–K2SiF6 melt for lithium-ion power sources
Silicon and silicon-based materials are increasingly used in microelectronics, metallurgy and power generation. To date the active study aimed at the development of silicon materials to be used in devices for solar energy conversion, accumulation and storage is underway. In addition, silicon is a promising anode material for lithium-ion fuel cells. In the present paper a possibility of silicon electroreduction from the NaI–KI–K2SiF6 melt in the argon atmosphere is studied. With this aim in view the electrolysis of the NaI–KI–K2SiF6 melt with glassy carbon cathode was performed under galvanostatic and potentiostatic regimes at the temperatures ranging from 650 to 750 °С. The morphology, phase and elemental analyses of the obtained silicon deposits were performed after their separation from the electrolytes by the ICP, SEM-EDX, XRD and Raman spectroscopy methods. Fiber and thread-like silicon samples of 60 to 320 nm in dimeter with admixtures concentrations (mainly oxygen) from 1.2 to 4.6 wt.% were experimentally synthesized. The obtained samples were tested as possible Si/C composite anodes for lithium-ion power sources. The discharge capacity of such power sources after 30 cycles of lithiation-delithiation ranged from 440 to 565 mAh·g–1 and the coloumbic efficiency ranged from 89 to 91%.
- Open Access
- 1 February 2022
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 169 (2) , 020537
Electrodeposition of Silicon from Molten KCl-K2SiF6 for Lithium-Ion Batteries
In this paper we report characteristics and electrochemical properties of silicon fibers used as lithium-ion battery anode. All samples were synthesized by potentiostatic electrodeposition from molten KCl–K2SiF6. From molten KCl–CsCl–K2SiF6 deposition was carried out in galvanostatic mode. Despite the synthesis in inert atmosphere and absence of oxygen containing compounds in the melt resulting silicon after washing contains at least 15 at% oxygen. Silicon fibers synthesized at −250 mV (vs Si) were the thinnest with diameter as small as 100 nm; average fiber length increased with increasing overvoltage. Addition of CsCl to the melt results in decrease of the average fibers diameter. Silicon fibers synthesized at −250 mV (vs Si) in KCl–K2SiF6 melt showed the best cycling performance with capacity of 1030 mAh·g−1 at 0.2 A·g−1 discharge current and capacity of 715 mAh·g−1 after 10 cycles. Lithium diffusion coefficients calculated from galvanostatic intermittent titration technique (GITT) are common for silicon-based anode. The highest initial diffusion coefficient value of 6.68·10−11 cm2·s−1 was achieved for silicon synthesized from melt with addition of CsCl. Low capacity and rapid capacity fading for all samples can be caused by high silicon dioxide content, further treatment of synthesized silicon is necessary to achieve higher performance.
- 1 February 2022
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 169 (2) , 020537
Open AccessElectrodeposition of Silicon from Molten KCl-K2SiF6 for Lithium-Ion Batteries
In this paper we report characteristics and electrochemical properties of silicon fibers used as lithium-ion battery anode. All samples were synthesized by potentiostatic electrodeposition from molten KCl–K2SiF6. From molten KCl–CsCl–K2SiF6 deposition was carried out in galvanostatic mode. Despite the synthesis in inert atmosphere and absence of oxygen containing compounds in the melt resulting silicon after washing contains at least 15 at% oxygen. Silicon fibers synthesized at −250 mV (vs Si) were the thinnest with diameter as small as 100 nm; average fiber length increased with increasing overvoltage. Addition of CsCl to the melt results in decrease of the average fibers diameter. Silicon fibers synthesized at −250 mV (vs Si) in KCl–K2SiF6 melt showed the best cycling performance with capacity of 1030 mAh·g−1 at 0.2 A·g−1 discharge current and capacity of 715 mAh·g−1 after 10 cycles. Lithium diffusion coefficients calculated from galvanostatic intermittent titration technique (GITT) are common for silicon-based anode. The highest initial diffusion coefficient value of 6.68·10−11 cm2·s−1 was achieved for silicon synthesized from melt with addition of CsCl. Low capacity and rapid capacity fading for all samples can be caused by high silicon dioxide content, further treatment of synthesized silicon is necessary to achieve higher performance.