XPXueting Pan

Xueting Pan

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Xueting Pan has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Review of Flexible Robot Stiffness Modulation Strategies

    by 潘雪婷,杨飞,耿中泰,岳洪浩,徐金随,王哲平, Yang Fei Pan Xueting

  • Design and Performance Analysis of a Bionic Squid Underwater Thruster

    by Xueting Pan, Yong Zhao, Fei Yang, Honghao Yue, Zhongtai Geng


  • Origami-inspired triboelectric sensor (TES) for shape detection of underwater thruster

    by Xueting Pan, Cao Li, Fei Yang, Yong Zhao, Honghao Yue, Zhongtai Geng

    The shape change of the thruster can reflect its motion state, and motion control of the thruster can be carried out more effectively by monitoring its motion state. The unique structure of the origami thruster increases the difficulty of sensor configuration, which significantly limits the application of origami structures (ORSs) in the thruster field. To solve the above problems, we propose a triboelectric sensor (TES) based on a triboelectric nanogenerator, which can be perfectly matched with an ORS and used to monitor the shape of an underwater thruster. The TES proposed can sense the folding angle of the structural unit of the origami thruster and then monitor its shape. The effects of different friction layer materials, different friction layer thicknesses, and multiple pairs of friction subs in series/parallel were analyzed on TES output characteristics. A scheme with thin copper sheets as electrodes, the polyethylene terephthalate resin as dielectric layers, and four pairs of friction pairs connected in parallel were selected for sensor performance testing. Finally, the origami thruster and TES are assembled for underwater testing. The shape of the origami thruster was monitored using the TES. The dihedral angle that TES can detect ranges from 22.5° to 63.5°, corresponding to the radius variation of the thruster ranging to 44.4%. The maximum error between the output result and the measured value was 4.19%, which proves that TES has a good detection effect on the shape change of the thruster and has a broad application prospect in robot motion monitoring.

  • Open Access

    Stiffness Analysis of Cable-Driven Parallel Robot for UAV Aerial Recovery System

    by Jun Wu, Honghao Yue, Xueting Pan, Yanbing Wang, Yong Zhao, Fei Yang

    Unmanned Aerial Vehicle (UAV) aerial recovery is a challenging task due to the limited maneuverability of both the transport aircraft and the UAV, making it difficult to establish an effective capture connection in the airflow field. In previous studies, we proposed using a Cable-Driven Parallel Robot (CDPR) for active interception and recovery of UAVs. However, during the aerial recovery process, the CDPR is continuously subjected to aerodynamic loads, which significantly affect the stiffness characteristics of the CDPR. This paper conducts a stiffness analysis of a single cable and a CDPR in a flow field environment. Firstly, we derive the stiffness matrix of a single cable based on a model that considers aerodynamic loads. The CDPR is then divided into elements using the finite element method (FEM), and the stiffness matrix for each element is obtained. These element stiffness matrices are assembled to form the stiffness matrix of the CDPR system. Secondly, we analyze the stiffness distribution of a single cable at various equilibrium positions within a flow field environment. Aerodynamic loads were observed to alter the equilibrium position of the cable, thereby impacting its stiffness. The more the cable bends, the greater the reduction in its stiffness. We examine the stiffness distribution characteristics of the CDPR’s end-effector within its workspace and analyze the impact of varying flow velocities and different cable materials on the system’s stiffness. This research offers a methodology for analyzing the stiffness of CDPR systems operating in a flow field environment.


  • Open Access

    Research on the Performance of Slender Aircraft with Flare-Stabilized-Skirt

    by Xueting Pan, Honghao Yue, Shufeng Liu, Fei Yang, Yifan Lu, Gang Chen

    In this paper, a morphing aircraft with a deployable flared skirt is proposed, and the influence of the flare skirt on the static stability of hypersonic aircraft is studied. The theoretical model of static stability of slender aircraft is established, and the position of the center of pressure can be used as a theoretical basis to measure static stability. Three-dimensional compressible Reynolds-averaged Navier–Stokes (RANS) solver and an SST k-ω turbulence model are used to analyze the aerodynamic characteristics of the aircraft and the influence effect of the flared skirt on the pressure distribution of the body, and the influence trend on the position of the pressure center is verified. At the same time, the reliability of the code and grid is verified by a classic example, and the results are in good agreement with the experimental data in the current literature. Finally, the static stability of an aircraft with flared skirts with different deployment angles is quantitatively measured by defining the stability derivative at the common point. The results show that the static stability of the aircraft with the same forebody is improved by more than 100% under different flight Mach numbers when the flared skirt deployment angle is 30° compared to 0°.


  • A shape memory alloy actuated release device using non-self-locking thread

    by Xueting Pan, Honghao Yue, Yun Tian, Qi Yao, Fei Yang, Yifan Lu

    This paper proposes a novel non-explosive and resettable release device driven by shape memory alloy (SMA), which can replace the commonly used pyrotechnic device. In the scheme, a flywheel nut with bidirectional thread is connected with two screws through the non-self-locking thread, and the target adapters are fixed with the two screws and then locked into a hole by the flywheel nut. When unlocking, the offset SMA actuator releases the flywheel nut by triggering the pulley assembly and multi-level levers. Under the pulling force of the pre-tightening load of the screws, the flywheel nut rotates at high speed to unlock the screws, thus releasing the target adapters. After separation, the device can be quickly reset with the reset tool without replacing any parts. The prototype of the release device is fabricated and tested; according to the performance test results, the device can bear the maximum bi-directional preload of 10 kN and the average unlocking force is 9.73 N. The unlocking time decreases with the increase in driving voltage, and the average unlocking response time is 342 ms under 9 V voltage. Furthermore, the actuator can function well with a lifetime of more than 50 cycles. It is concluded that this scheme has potential advantages to replace the traditional non-reusable explosive driving device.