Ildikó Maňková
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ildikó Maňková has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Marek Vrabeľ
Technical University of Košice
3 shared publications Jozef Beňo
2 shared publications- Balázs Mikó
Óbuda University
1 shared publication - Daniel Kottfer
Faculty of Special Technology, Alexander Dubcek University of Trencin, Ku kyselke 469, 911 06 Trenčín, Slovakia
1 shared publication Miroslav Paľo
Technical University Košice
1 shared publicationMária Franková
Technical University Košice
1 shared publication
Latest Publications
- 1 August 2017
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 261, 17-21
Evaluation of Relationship between Cutting Parameters and Torque in Hole Making of Titanium Alloy
In terms of machinability are titanium alloys classified in the group of difficult to cut materials. The main factors determining this status are limited tool life, high generated cutting forces (torque) and temperature in cutting zone caused by low thermal conductivity as well as chemical reactivity with cutting tool. Solid carbide drills still remain as preferred choice in hole making process when machining Ti6Al4V alloy. Besides cutting conditions, tool and cutting edge geometry significantly affect the value of torque. Reduction of process energy requirements can be achieved by appropriate optimization of these parameters. Mathematical model describing influence of cutting speed, feed rate, clearance angle and cutting edge radius on investigated variable with high reliability coefficient (R2=96.72%) was found. Drilling experiments were designed and carried out using Taguchi orthogonal array L16.
- 1 August 2017
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 261, 17-21
Evaluation of Relationship between Cutting Parameters and Torque in Hole Making of Titanium Alloy
In terms of machinability are titanium alloys classified in the group of difficult to cut materials. The main factors determining this status are limited tool life, high generated cutting forces (torque) and temperature in cutting zone caused by low thermal conductivity as well as chemical reactivity with cutting tool. Solid carbide drills still remain as preferred choice in hole making process when machining Ti6Al4V alloy. Besides cutting conditions, tool and cutting edge geometry significantly affect the value of torque. Reduction of process energy requirements can be achieved by appropriate optimization of these parameters. Mathematical model describing influence of cutting speed, feed rate, clearance angle and cutting edge radius on investigated variable with high reliability coefficient (R2=96.72%) was found. Drilling experiments were designed and carried out using Taguchi orthogonal array L16.
- 1 April 2016
- Published by Elsevier in Measurement
- Vol. 84, 7-20
An approach to the evaluation of multivariate data during ball end milling free-form surface fragments
- 1 April 2016
- Published by Elsevier in Measurement
- Vol. 84, 7-20
An approach to the evaluation of multivariate data during ball end milling free-form surface fragments
- 1 October 2013
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 581, 329-334
Influence of Tool Path Orientation on the Surface Roughness when End Ball Milling Rounded Surfaces
Paper deals with relationships affecting surface roughness in three dimensional milling. Because of definite curvature of the machined surface, three milling strategies based on single direction have been examined in end ball milling process. Research is based on fragmentation of the definite surface curvature into form of the patches being machined. Patches have been set through normal vectors and related axes of motion of the end ball milling cutters. Surface quality has been identified under influence of cutting speed, feed rate and side step of milling cutters. Simple geometrical models of the resultant cusp height are compared with the measured data.
- 1 October 2013
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 581, 329-334
Influence of Tool Path Orientation on the Surface Roughness when End Ball Milling Rounded Surfaces
Paper deals with relationships affecting surface roughness in three dimensional milling. Because of definite curvature of the machined surface, three milling strategies based on single direction have been examined in end ball milling process. Research is based on fragmentation of the definite surface curvature into form of the patches being machined. Patches have been set through normal vectors and related axes of motion of the end ball milling cutters. Surface quality has been identified under influence of cutting speed, feed rate and side step of milling cutters. Simple geometrical models of the resultant cusp height are compared with the measured data.