АИАнастасия Валерьевна Игнатова

Анастасия Валерьевна Игнатова

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Анастасия Валерьевна Игнатова has a total of 29 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Experimental study of the fixation properties of various biomechanical options for plate osteosynthesis of comminuted impaction fractures of the tibial plateau

    by Mikhail E. Kupitman, Igor A. Atmansky, Anastasia V. Ignatova

    BACKGROUND: Various biomechanical options are used in surgical practice to fix osteochondral fragments, including support on a bone graft reinforced with subchondral wires, osteosynthesis with forked fixators, and specialized plates with screws placed directly under the articular surface fragments. In the work, a method of subchondral tensioned reinforcement was utilized. AIM: The work aimed to evaluate and compare the fixation properties of different biomechanical osteosynthesis options for comminuted intra-articular fractures using porcine tibial bone models. METHODS: An indented, single-center, non-blinded experimental study included two types of models that shared identical fracture configurations, bone defect parameters, and non-tensioned wire reinforcement: A, with the bone defect filled with a graft, and B, without a bone graft. The results of osteosynthesis in models A and B were examined: 1) plate osteosynthesis with support of the articular surface on a bone autograft, option A-I; 2) plate osteosynthesis with support of the articular surface on the plate’s fixing elements and the bone graft, option A-II; 3) plate osteosynthesis with fixation of articular surface fragments using U-shaped tensioned wires, option B-III; 4) osteosynthesis with fixation of the articular surface using tensioned subchondral wires in a modular plate-based fixation device, option B-IV. Testing was performed under static indentation on models from the proximal metaphyseal-epiphyseal region of porcine tibia. RESULTS: The best fixation properties were observed in the tensioned subchondral reinforcement options B-III and B-IV compared with non-tensioned wire reinforcement (model A). When comparing the four biomechanical options, the best strength characteristics were observed in the variants with tensioned subchondral reinforcement: B-III and B-IV. In the study of Option A-II, the resistance of the biomechanical system to vertical load was lower than in Options B-III and B-IV. The worst variants were observed in option A-I. CONCLUSION: The most effective fixation was achieved with tensioned subchondral reinforcement using U-shaped wires (B-III) and a modular plate-based fixation device (B-IV) without the use of an additional bone graft.

  • Open Access

    Deformation and failure of laminated fabric fiber-glass reinforced plastic during bending on an annular support: effect of 3D reinforcement and loading rate

    by Galina Forental, Sergey Sapozhnikov, Anastasiya Ignatova, Ol’ga Buslaeva, Aleksandr Kheruvimov

    Felting is a needle-punching technology in which the impacts of barbed needles partially damage the dry fibers of the fabric stack and pull them normally to the surface. The result is transversal reinforcement at a given impact density per 1 cm2 in the local area. In this work, the effect of felting on the resistance to bending on the annular support of laminated fabric fiber-glass reinforced plastic at various loading rates is experimentally studies. During quasi-static tests, the area of defects observed by the backlit of the specimens with felting decreases by approximately 20% compared to the specimens without felting at indenter diameters of 10 and 20 mm. During the low-velocity impact tests, the damaged area decreases on average by 9% (velocity is 1.93 m/s) and 15% (velocity is 2.4 m/s) with felting at an indenter diameter of 10 mm. For a diameter of 20 mm, the damaged area with felting also decreases compared with the specimens without felting (by 11% at 1.42 m/s, by 22% at 1.98 m/s, and by 34% at 2.42 m/s). The experimental results show that even the minimum density felting (10 cm-2 ) significantly reduces the delamination area (up to 34%) during a local impact.

  • Prediction of GFRP Self-Heating Kinetics Under Cyclic Bending

    by A. V. Ignatova, A. V. Bezmelnitsyn, N. A. Olivenko, O. A. Kudryavtsev, S. B. Sapozhnikov, A. D. Shavshina


  • Open Access

    ANALYSIS OF MESOSTRUCTURE AND FRACTURE KINETICS OF ELEMENTS OF LATTICE COMPOSITE STRUCTURES UNDER TRANSVERSAL COMPRESSION USING STOCHASTIC FEA MICROMECHANICS

    by S. B. Sapozhnikov, N. A. Shaburova, A. V. Ignatova, A. N. Shanygin, Сапожников С. Б., Шабурова Н. А., Игнатова А. В., Шаныгин А. Н.

    The paper analyses the mesostructure of the structural elements of lattice aircraft shells – ribs consisting of alternating layers of equal thickness and made from unidi-rectional CFRP and pure matrix material. In experimental studies, the elastic characteristics of unidirectional CFRP were obtained under three-point bending and transversal compression. As a result, the longitudinal modulus of elasticity of the layered composite turned out to be 101 GPa, and the shear modulus was 2.95 GPa. Numerical modeling of the meso- and micromechanics of the interaction of the noticed layers under transversal compression has been performed up to failure. The ANSYS FEA software (explicit and implicit formulations) was used. The regular and stochastic stacking of fibres in the cross section under compression is considered. The fiber diameters in the composite element were measured on thin sections using a Zeiss Axio Observer D1m digital microscope and were equal to 5.1 ± 0.8 µm. Layers with a fiber volume fraction of about 60 % alternate with layers of pure epoxy. It is proposed to use only the first principal stress in the matrix as a micromechanical criterion for failure under com-pression and tension. At the first stage of calculations, the problem of transversal compression of a cell with a regular laying of fibres was solved (the error in the value of the transversal modulus of elasticity was less than 2 %). At the second stage, an assessment was made of the strength and accumulation of microdamages under compression in a model of a layered structure with stochastic fibre stacking. The analysis of stress-strain state of a layered mesostructure under compression made it possible to explain the reason that the rib has a trans-verse strength twice lower than that of a homogeneous CFRP. The calculated values of the ultimate strength in transversal compression of a layered rib are in good agreement with the experimental ones.


  • Прогнозирование саморазогрева стеклопластика при циклическом изгибе

    by А. В. Игнатова, Южно-Уральский Государственный Университет, А. В. Безмельницын, Н. А. Оливенко, О. А. Кудрявцев, С. Б. Сапожников, А. Д. Шавшина

    Эффект саморазогрева, обусловленный внутренним трением, — актуальная проблема при проектировании и эксплуатации циклически нагруженных элементов конструкций из стеклопластиков. Вибрация аэрокосмических конструкций с большими амплитудами и высокими частотами, а также ускоренные механические испытания могут привести к повышению температуры композита, деградации механических свойств и преждевременному разрушению. Цель исследования — изучение кинетики саморазогрева стеклопластика при знакопеременном изгибе. Для описания кинетики саморазогрева композита при нормальном конвективном теплообмене разработана малопараметрическая аналитическая модель. Для проверки результатов моделирования разработали оригинальный клиновидный образец и экспериментальную установку. Испытания на циклический изгиб провели при частотах от 10 до 20 Гц и амплитудах перемещений от 4 до 7 мм. Предложенная модель позволяет с приемлемой точностью предсказать зависимость максимальной температуры композита от времени, частоты и амплитуды.


  • Open Access

    The Influence of thickness on residual flexural strength of composite with low-velocity impact damages: Experimental study

    by O. A Kudryavtsev, A. V Ignatova, N. A Olivenko

    Assessment of the residual strength of composite structural elements that can be subjected to low-velocity impact during operation is still a vital engineering problem. Its solution requires not only the understanding of the basic mechanisms of energy dissipation in composites but, the study of factors affecting the impact resistance of the material. The thickness is one of the main parameters that affects the mechanical behaviour of the composite at low-velocity impacts and, as a consequence, its residual strength. This paper presents the experimental study of the material thickness and impact energy influence on the residual flexural strength of woven glass fibre-reinforced plastic specimens. At the first stage of the study, low-velocity impact tests with different impact energies on GFRP plate specimens with the thickness of 2 mm, 4 mm, and 6 mm were carried out. At the second stage, the beam specimens were cut out from the plate specimens with impact damages, and three-point bending tests were carried out. The dependencies of the residual flexural strength were obtained at various impact energies for all specimen thicknesses. The sensitivity of the Flexure-After-Impact test protocol to the delamination and fibre damages in the composite specimens were assessed.


  • Open Access

    Prolonged Thermal Relaxation of the Thermosetting Polymers

    by Alexander Korolev, Maxim Mishnev, Nikolai Ivanovich Vatin, Anastasia Ignatova

    The rigidity of structures made of polymer composite materials, operated at elevated temperatures, is mainly determined by the residual rigidity of the polymer binder (which is very sensitive to elevated temperatures); therefore, the study of ways to increase the rigidity of polymer materials under heating (including prolonged heating) is relevant. In the previous research, cured thermosetting polymer structure’s non-stability, especially under heating, is determined by its supra-molecular structure domain’s conglomerate character and the high entropy of such structures. The polymer elasticity modeling proved the significance of the entropy factor and layer (EPL) model application. The prolonged heating makes it possible to release adsorptive inter-layer bonds and volatile groups. As a result, the polymer structure is changing, and inner stress relaxation occurs due to this thermo-process, called thermo-relaxation. The present study suggests researching thermo-relaxation’s influence on polymers’ deformability under load and heating. The research results prove the significant polymer structure modification due to thermo-relaxation, with the polymer entropy parameter decreasing, the glassing onset temperature point (Tg) increasing by 1.3–1.7 times, and the modulus of elasticity under heating increasing by 1.5–2 times.


  • Open Access

    Development of Computer Models of Modified Aramid Fabric

    by Наталья Юрьевна Долганина, Анастасия Валерьевна Игнатова, Иван Сергеевич Слободин

    Разработка компьютерных моделей модифицированных арамидных тканей

  • Open Access

    The development of computer models of ballistic fabric with surface treatment

    by Наталья Юрьевна Долганина, Анастасия Валерьевна Игнатова

    Баллистические ткани на сегодняшний день широко применяются в качестве элементов защитных структур. Актуальными задачами при разработке бронеструктур являются минимизация их массы, уменьшение кинетической энергии пули, передаваемой объекту, расположенному за бронепанелью (снижение величины прогиба тыльной стороны панели). Значительная часть энергии пули рассеивается за счет работы сил трения при вытягивании нитей из ткани. Умение предсказывать работу баллистической ткани при вытягивании нитей позволит проектировать высокоэффективные бронеструктуры. Поэтому были разработаны малопараметрические численные модели вытягивания нити из арамидной ткани Р110 полотняного переплетения, а также для этой ткани с разными типами поверхностной обработки (канифоль, силиконовая смазка) в пакете программ LS-DYNA. Поверхностная обработка ткани позволяет изменять коэффициент трения между нитями с минимальным увеличением веса, и в модели она учитывалась за счет изменения одного параметра — коэффициента сухого трения. Рассмотрено несколько способов распараллеливания задачи вытягивания нити из ткани, получены графики ускорения. Были получены расчетные зависимости нагрузки от перемещения при вытягивании нити из ткани с поверхностной обработкой и без нее. Расчетные результаты лежат в диапазоне разброса экспериментальных данных.