Qi Yu
Research Subjects
Qi Yu has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Jun Yang
State Key Laboratory of Explosion Science and Technology, Beijing Institute of Technology, Beijing 100081, China
3 shared publications - Hongliang Tang
China Safety Technology Research Academy of Ordnance Industry, Beijing 100053, China
2 shared publications - Li Yuan Chi
Oulu Mining School, University of Oulu, Oulu, Finland
1 shared publication - Xin Liu
School of Mining Engineering, University of Science and Technology Liaoning, Liaoning Anshan, China
1 shared publication - Xuan Xu
School of Safety Engineering, Beijing Institute of Petrochemical Technology, Beijing, China
1 shared publication
Latest Publications
- Open Access
- 20 June 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (12) , 7329
Experimental Investigation of the Effect of Delay Time on Rock Fragmentation in Multi-Hole Bench Blasting
Rock fragmentation by blasting influences ore recovery and the cost of downstream operations. The development of electronic detonators makes it possible to improve fragmentation by controlling the initiation timing in blasting projects, and the effect of the mechanism of delay timing on rock fragmentation should be studied. Fragmentation of granite bench specimens with different initiation timing was investigated in blast experiments. Conclusions are obtained by studying the surface strain field and post-blast specimens. A total of six blasting tests were carried out on granite bench specimens with four boreholes each having a diameter of 10 mm and a length of 450 mm. Each borehole used pentaerythritol tetranitrate (PETN) as the explosive charge, which was approximately 4.84 g with a charge diameter of 5.5 mm. Delay times between adjacent boreholes in the same row were set as 0, 50, 100, 150, 200, and 250 µs. The surface strain field of the bench specimen under blast loading was analyzed using three-dimensional digital image correlation (3D-DIC) techniques based on two cameras that captured high-speed images. Additionally, the post-blast specimen was also observed and recorded. Fragments of each bench specimen were carefully collected, weighed, and sieved with a set of sieves, including very fine particles. According to the 3D-DIC analysis for bench specimens, the propagation pattern of the main strain concentration zone transformed from horizontal to vertical with the increase in inter-hole delay. The maximum blast excavation weight was obtained by the bench specimen with an inter-hole delay of 100 µs, while the bench specimen with the longest inter-hole delay (250 µs) obtained the minimum blast excavation weight. By combining the results for blast excavation weight with the results from fragment size distribution analysis of all specimens, the optimal inter-hole delay was 200 µs. Compared to simultaneous detonation, the median size was decreased by about 14.5% for the inter-hole delay of 200 µs. The results of experiments show that delay time significantly influences rock fragmentation, but the stress wave superposition in short delays cannot improve rock fragmentation. For long delays, the blast-induced crack propagation time should be regarded as an influential factor when choosing the proper delay time. The experimental findings of this study could provide a better understanding of the effect of the mechanism of delay time on rock fragmentation.
- 20 June 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (12) , 7329
Open AccessExperimental Investigation of the Effect of Delay Time on Rock Fragmentation in Multi-Hole Bench Blasting
Rock fragmentation by blasting influences ore recovery and the cost of downstream operations. The development of electronic detonators makes it possible to improve fragmentation by controlling the initiation timing in blasting projects, and the effect of the mechanism of delay timing on rock fragmentation should be studied. Fragmentation of granite bench specimens with different initiation timing was investigated in blast experiments. Conclusions are obtained by studying the surface strain field and post-blast specimens. A total of six blasting tests were carried out on granite bench specimens with four boreholes each having a diameter of 10 mm and a length of 450 mm. Each borehole used pentaerythritol tetranitrate (PETN) as the explosive charge, which was approximately 4.84 g with a charge diameter of 5.5 mm. Delay times between adjacent boreholes in the same row were set as 0, 50, 100, 150, 200, and 250 µs. The surface strain field of the bench specimen under blast loading was analyzed using three-dimensional digital image correlation (3D-DIC) techniques based on two cameras that captured high-speed images. Additionally, the post-blast specimen was also observed and recorded. Fragments of each bench specimen were carefully collected, weighed, and sieved with a set of sieves, including very fine particles. According to the 3D-DIC analysis for bench specimens, the propagation pattern of the main strain concentration zone transformed from horizontal to vertical with the increase in inter-hole delay. The maximum blast excavation weight was obtained by the bench specimen with an inter-hole delay of 100 µs, while the bench specimen with the longest inter-hole delay (250 µs) obtained the minimum blast excavation weight. By combining the results for blast excavation weight with the results from fragment size distribution analysis of all specimens, the optimal inter-hole delay was 200 µs. Compared to simultaneous detonation, the median size was decreased by about 14.5% for the inter-hole delay of 200 µs. The results of experiments show that delay time significantly influences rock fragmentation, but the stress wave superposition in short delays cannot improve rock fragmentation. For long delays, the blast-induced crack propagation time should be regarded as an influential factor when choosing the proper delay time. The experimental findings of this study could provide a better understanding of the effect of the mechanism of delay time on rock fragmentation.
- Open Access
- 21 December 2022
- Published by MDPI AG in Applied Sciences
- Vol. 13 (1) , 85
Experimental Study on the Influence of Delay Time on Rock Fragmentation in Bench Blasting
Delay time is an important factor in the quality of bench blasting. The development and application of electronic detonators make it possible to control the timing of detonation by a highly precise delay time. It is an easily achievable way to seek a better blast fragmentation by controlling the delay time. In order to investigate the influence of delay time on rock fragmentation, eight experiments on bench blasting models with double holes were carried out. The average weight of 4.59 g of pentaerythritol tetranitrate (PETN) was charged into each blast hole with a diameter of 10 mm. Delay times between the double holes were set as: 13.69, 27.36, 54.72, 60, 90, 120, 180, and 339.6 µs. During blast loading, the breakage processes of specimens were captured in detail by high-speed cameras. Full-field strains on the bench slope were analyzed by the three-dimensional digital image correlation (3D-DIC) technique. After each experiment, the coarse fragments were backfilled into the post-blast specimen to observe and record the bench slope’s final breakage pattern. The experimental results showed that the fragmentation of the bench slope transformed from horizontal crack dominance to vertical crack dominance as the delay time increased. In addition, post-blast fragments were collected and sieved, including fine materials. In the premise of approximate excavation, the optimum delay time was 180 µs. Compared to short delay times such as 27.36 µs, x50 was improved by approximately 25% at the delay time of 180 µs. The results showed a significant difference and great improvement in fragmentation when the delay times were in the time range of no-shock-wave interaction compared to interactions. When determining the optimum delay time in multi-hole blasting, except for the stress wave interaction, factors such as crack propagation should also be considered. The results of experiments could contribute to references for relevant research.
- 21 December 2022
- Published by MDPI AG in Applied Sciences
- Vol. 13 (1) , 85
Open AccessExperimental Study on the Influence of Delay Time on Rock Fragmentation in Bench Blasting
Delay time is an important factor in the quality of bench blasting. The development and application of electronic detonators make it possible to control the timing of detonation by a highly precise delay time. It is an easily achievable way to seek a better blast fragmentation by controlling the delay time. In order to investigate the influence of delay time on rock fragmentation, eight experiments on bench blasting models with double holes were carried out. The average weight of 4.59 g of pentaerythritol tetranitrate (PETN) was charged into each blast hole with a diameter of 10 mm. Delay times between the double holes were set as: 13.69, 27.36, 54.72, 60, 90, 120, 180, and 339.6 µs. During blast loading, the breakage processes of specimens were captured in detail by high-speed cameras. Full-field strains on the bench slope were analyzed by the three-dimensional digital image correlation (3D-DIC) technique. After each experiment, the coarse fragments were backfilled into the post-blast specimen to observe and record the bench slope’s final breakage pattern. The experimental results showed that the fragmentation of the bench slope transformed from horizontal crack dominance to vertical crack dominance as the delay time increased. In addition, post-blast fragments were collected and sieved, including fine materials. In the premise of approximate excavation, the optimum delay time was 180 µs. Compared to short delay times such as 27.36 µs, x50 was improved by approximately 25% at the delay time of 180 µs. The results showed a significant difference and great improvement in fragmentation when the delay times were in the time range of no-shock-wave interaction compared to interactions. When determining the optimum delay time in multi-hole blasting, except for the stress wave interaction, factors such as crack propagation should also be considered. The results of experiments could contribute to references for relevant research.
- Open Access
- 26 November 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (23) , 11230
Experimental Study on the Temporal and Morphological Characteristics of Dynamic Tensile Fractures in Igneous Rocks
In order to investigate the temporal and morphological characteristics of dynamic tensile fractures, experiments on Brazilian specimens machined from igneous rocks (Breccia and Andesite) are carried out with the split Hopkinson pressure bar (SHPB). Detailed observation of the fracture processes of the Brazilian specimens is captured by high-speed camera at a frame rate of 100,000 frames per second. The rate-dependent effect of the dynamic tensile strength of the two igneous rocks is fitted and predicted by the incubation time criterion. Digital image correlation (DIC) is used to calculate the full-field tensile strain distributions on the specimen surface during the loading stage preceding fracture, and this hysteresis of dynamic fracture relative to stress level is interpreted by introducing the concept of incubation time. After the main crack appears, image processing technology is exploited to extract the pixel information of cracks in the high-speed images. Then, FracPaQ quantifies the morphology of the fragmentized process by filling the binarization of cracks with fracture traces. After coordination of the statistical information from these fracture traces, the rose diagram representing their angles and length weights can visually represent the fragmentized characteristics of the Brazilian specimen. Specifically, length-angle distributions of fracture traces at various moments are consistent with the Gaussian function, and the curve fitting parameters reflect differences in the fracture behaviors between the two igneous rocks. In conclusion, the dynamic fracture characteristics of two igneous rocks in dynamic splitting processes are quantified statistically, which can provide references for relevant research.
- 26 November 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (23) , 11230
Open AccessExperimental Study on the Temporal and Morphological Characteristics of Dynamic Tensile Fractures in Igneous Rocks
In order to investigate the temporal and morphological characteristics of dynamic tensile fractures, experiments on Brazilian specimens machined from igneous rocks (Breccia and Andesite) are carried out with the split Hopkinson pressure bar (SHPB). Detailed observation of the fracture processes of the Brazilian specimens is captured by high-speed camera at a frame rate of 100,000 frames per second. The rate-dependent effect of the dynamic tensile strength of the two igneous rocks is fitted and predicted by the incubation time criterion. Digital image correlation (DIC) is used to calculate the full-field tensile strain distributions on the specimen surface during the loading stage preceding fracture, and this hysteresis of dynamic fracture relative to stress level is interpreted by introducing the concept of incubation time. After the main crack appears, image processing technology is exploited to extract the pixel information of cracks in the high-speed images. Then, FracPaQ quantifies the morphology of the fragmentized process by filling the binarization of cracks with fracture traces. After coordination of the statistical information from these fracture traces, the rose diagram representing their angles and length weights can visually represent the fragmentized characteristics of the Brazilian specimen. Specifically, length-angle distributions of fracture traces at various moments are consistent with the Gaussian function, and the curve fitting parameters reflect differences in the fracture behaviors between the two igneous rocks. In conclusion, the dynamic fracture characteristics of two igneous rocks in dynamic splitting processes are quantified statistically, which can provide references for relevant research.