BCBing-Ruei Chuang

Bing-Ruei Chuang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Bing-Ruei Chuang has a total of 4 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Design and Implementation of a 28-GHz Four-Phase Beam-Steering Antenna Based on a Butler Matrix Network

    by Ming-An Chung, Chia-Wei Lin, Bing-Ruei Chuang

    This paper presents a four-phase beam-steering antenna for 28 GHz wireless communication, targeting the demand for high-efficiency and low-complexity beam-steering solutions in millimeter-wave systems. The proposed design employs a Butler matrix network to achieve multi-directional beam switching while reducing implementation complexity. The antenna is realized using microstrip technology on a printed circuit board (PCB), and the overall architecture consists of a 1 × 4 microstrip antenna array and a 4 × 4 Butler matrix network. Each component is carefully designed and analyzed to ensure optimized performance and proper system balance. The proposed antenna exhibits excellent performance in terms of bandwidth and compact size, while also providing advantages that include low cost, ease of fabrication, and structural simplicity. The beam-steering capability is experimentally verified through far-field measurements. The measurement results indicate that the four beam directions are −38°, −13°, +19°, and +41°, with corresponding gains of 8.79, 9.66, 10.8, and 9.21 dBi, respectively. In addition, a good agreement between the measurement and simulation results is observed, which validates the effectiveness and feasibility of the proposed design.

  • Open Access

    A Compact On-Chip Ka-Band Bandpass Filter Using Folded Crossed Interdigital Coupling Structure

    by Ming-An Chung, Chia-Wei Lin, Bing-Ruei Chuang

    This paper proposes a millimeter-wave miniature on-chip bandpass filter (BPF) implemented using a 0.18 μm CMOS process. To address the issues of insufficient coupling capability, limited control of transmission zeros, and excessive chip area in traditional on-chip filters, a folded cross-interdigital coupling structure is proposed to enhance coupling efficiency and reduce size. The design incorporates metal–insulator–metal (MIM) capacitors to increase the coupling capacitance between resonators without increasing the area, and utilizes a defected ground structure (DGS) to modify the current distribution at the ground plane, generating additional transmission zeros to improve selectivity. An LC equivalent circuit model was established and verified through full-wave electromagnetic simulation, and the design was validated through chip fabrication and on-wafer measurements. The measurement results show an insertion loss of 3.36 dB and a fractional bandwidth of 49.1% at 32 GHz, with two transmission zeros. The core dimensions are 0.25 mm × 0.18 mm. This design achieves a good balance between miniaturization, selectivity, and insertion loss, making it suitable for millimeter-wave SoC applications.

  • Open Access

    On-Chip Yagi Antenna Design at 38 GHz with 0.18 μm CMOS Techniques

    by Chia-Wei Lin, Ming-An Chung, Bing-Ruei Chuang

    In this study, a 38 GHz millimeter wave Yagi antenna was designed and fabricated on a chip using a 0.18 μm CMOS process. The radiation performance of the antenna is improved by using a Yagi antenna with end-fire. The proposed antenna chip measures the reflection coefficient at less than −10 dB over a bandwidth range from 36.6 to 39.8 GHz, covering the 5G n260 band. The CMOS antenna chip has a size of 1.2×1.2 mm2. This study also proposes a solution for the easy measurement of the radiation characteristics to verify the performance in millimeter wave applications. For this purpose, the chip antenna uses bonding wire technology and is verified in a millimeter wave test system. Finally, the simulation and measurement results of the antenna pattern of the bondline technique yield similar radiation patterns.


  • Open Access

    4 × 4 MIMO Antenna System for Smart Eyewear in Wi-Fi 5G and Wi-Fi 6e Wireless Communication Applications

    by Ming-An Chung, Cheng-Wei Hsiao, Chih-Wei Yang, Bing-Ruei Chuang

    This paper proposes a small-slot antenna system (50 mm × 9 mm × 2.7 mm) for 4 × 4 multiple-input multiple-output (MIMO) on smart glasses devices. The antenna is set on the plastic temple, and the inverted F antenna radiates through the slot in the ground plane of the sputtered copper layer outside the temple. Two symmetrical antennas and slots on the same temple and series capacitive elements enhance the isolation between the two antenna ports. When both temples are equipped with the proposed antennas, 4 × 4 MIMO transmission can be achieved. The antenna substrate is made of polycarbonate (PC), and its thickness is 2.7 mm εr=2.85, tanδ=0.0092. According to the actual measurement results, this antenna has two working frequency bands when the reflection coefficient is lower than −10dB, its working frequency bandwidth at 4.58–5.72 GHz and 6.38–7.0 GHz. The proposed antenna has a peak gain of 4.3 dBi and antenna efficiency of 85.69% at 5.14 GHz. In addition, it also can obtain a peak gain of 3.3 dBi and antenna efficiency of 82.78% at 6.8 GHz. The measurement results show that this antenna has good performance, allowing future smart eyewear devices to be applied to Wi-Fi 5G (5.18–5.85 GHz) and Wi-Fi 6e (5.925–7.125 GHz).